Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

needs H323 configuration example

hi all,

i have 2811 voice gateway with only 2 vic2-4fxo ports.

please can any one provide me with H323 configuration example that matches my case with a brief discription because i didn't configure H323 gateway before.

so please help

thanx in advance

3 REPLIES
Bronze

Re: needs H323 configuration example

BASIC RUN DOWN

1. configure dial-peers on router

example, if you have an fxo port say 1/0/0

and you want all calls to go through that

then

dial-peer voice 1 pot

destination-pattern .T

port 1/0/0

then for incoming calls to reach an extension create and VOIP dial-peer sending it to the ip of your CCM.

3. create an h323 gateway under device/gateway config. specify the IP of the rtr. it will always come up with unknown but with the ip registered. Make sure your CSS is correct.

4. create a route-pattern to whatever number you desire to pass through the FXO and under select gateway/hunt-list select the gateway.(Note to select specific ports first you need to use the preference command in the dial-peer)

basically, thats it however, there are a few other configs to ensure that voice takes the correct path. bind to the interface you want voice to pass,remove VAD if you hear "voice cuts on the line" allow rtp send-receve if you experience one-way audio(could be several other factors as well that may cause this).

and i think thats about that. im sure you will get some othe more specfic responses from the forum

New Member

Re: needs H323 configuration example

What is missing from this answer is the two h323-gateway lines un der one of the interfaces you need to choose to attach the h323-gateway to it as follows;

for example if you choose the loopback interface

you will have to have

h323-gateway voice interfcae enabled under this one and also the h323-gateway bind line is also enabled under it . Also you will have to use this interface ip add on the call manager when you configure the gateway in the device -- gateway -- h323-gateway type.

Bronze

Re: needs H323 configuration example

Here's a basic example from a 2600 with ISDN PRI. Should be enough to get you started.

!

ip cef

!

isdn switch-type primary-ni

!

!

voice service voip

h323

no h225 timeout keepalive

session transport udp

!

voice class codec 711

codec preference 1 g711ulaw

codec preference 2 g729r8

!

!

!

voice class h323 10

h225 timeout tcp establish 3

!

controller T1 0/0

framing esf

linecode b8zs

pri-group timeslots 1-24

!

interface FastEthernet0/0

ip address 192.168.1.31 255.255.255.0

duplex auto

speed auto

h323-gateway voip interface

h323-gateway voip id MyGateway ipaddr 192.168.1.31

!

interface Serial0/0:23

no ip address

encapsulation hdlc

isdn switch-type primary-ni

isdn incoming-voice voice

no cdp enable

!

dial-peer voice 4001 voip

description First CallManager

preference 1

incoming called-number ....

destination-pattern ^....$

voice-class codec 711

voice-class h323 10

session target ipv4:1.2.3.4

dtmf-relay h245-alphanumeric

!

dial-peer voice 4002 voip

description Second CallManager

preference 2

incoming called-number ....

destination-pattern ^....$

voice-class codec 711

voice-class h323 10

session target ipv4:5.6.7.8

dtmf-relay h245-alphanumeric

!

dial-peer voice 4003 voip

description Tertiary CallManager

preference 3

incoming called-number ....

destination-pattern ^....$

voice-class codec 711

voice-class h323 10

session target ipv4:1.2.8.9

dtmf-relay h245-alphanumeric

!

dial-peer voice 1 pots

description PSTN

incoming called-number ....

destination-pattern 9.T

direct-inward-dial

port 0/0:23

!

!

gatekeeper

shutdown

!

5179
Views
0
Helpful
3
Replies