Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

Night-service distinctive ring tone

As per CCM admin guide the notified ephone will get distinctive ring tone but I got same tone in 'ephone 2' before & after the 'night-service' mode.

I saw a message 'File is not found distict...' on 'ephone 2' while notified. I cannot find any file in flash as name 'distint...' Is this related to the issue?

Advise please,

ephone-dn 1

number 1000

night-service bell

!

ephone-dn 2

number 1001

!

ephone 1

button 1:1

!

ephone 2

button 1:2

night-service bell

Thanks,

10 REPLIES
Hall of Fame Super Gold

Re: Night-service distinctive ring tone

Hi,

the phone is looking for distinctiveringlist.xml, you must create the file, place it on the router in the tftp directory as well with the actual ringfiles you want for night-service.

Hope this helps, if so please rate post!

New Member

Re: Night-service distinctive ring tone

The CME admin guide didn't tell any about distinctiveringlist.xml file. Do I really need that file or able to achieve on CME4.0(2)?

Thanks,

Hall of Fame Super Gold

Re: Night-service distinctive ring tone

The CME guide sometime doesn't tell about a lot of things :)

Yes the file is required and you will need to enable it with "tftp-server" statement.

New Member

Re: Night-service distinctive ring tone

Okay, I downloaded the 'RingTone.tar' from CCO and changed the DistinctiveRingList.xml'

s 1st entry to 'Sax1.raw' but still I have same ring tone on 'ephone 2' before & after night-service.

what else do I need configure?

**Add the following in CME

tftp-server flash:DistinctiveRingList.xml

tftp-server flash:RingList.xml

tftp-server flash:Sax1.raw

Thanks,

Hall of Fame Super Gold

Re: Night-service distinctive ring tone

Hmmm... the tftp filenames are case sensitive.. Can you check with "debug tftp events" that the phone is actually getting the requested files ?

Is the message cone away on the phone ?

New Member

Re: Night-service distinctive ring tone

No tftp events when I dial the night target number 1000. follows my currnet environment. please advise what's wrong.

-2821, 12.4(11)XJ2

-CME 4.1(0)

Configuration

-------------

tftp-server flash:DistinctiveRingList.xml

tftp-server flash:RingList.xml

tftp-server flash:Sax1.raw

!

ephone-dn 1

number 1000

night-service bell

!

ephone-dn 2

number 1001

!

ephone 1

button 1:1

!

ephone 2

button 1:2

night-service bell

ccmelab#dir

-----------

Directory of flash:/

33 -rw- 489 Apr 18 2007 17:16:26 -05:00 DistinctiveRingList.xml

52 -rw- 495 Apr 18 2007 15:36:50 -05:00 RingList.xml

53 -rw- 10800 Apr 18 2007 15:36:50 -05:00 Sax1.raw

ccmelab#sh deb

--------------

TFTP:

TFTP Event debugging is on

TFTP Packet debugging is on

Hall of Fame Super Gold

Re: Night-service distinctive ring tone

Hi, which phone are you using? Is the night service displayed and active ?

I could to try this as well with CME 4.1

New Member

Re: Night-service distinctive ring tone

dial '1000' and the notificatoin to 'ephone 2' which associated to '1001' in my configuration. Yes, display on the IP phone 'Night Service Active'.

ephone 2 successfully rining the notification but the ring tone is same before & after 'Night Service' mode.

Thanks,

Hall of Fame Super Gold

Re: Night-service distinctive ring tone

Ok, which phone types ? I can try it with most types.

New Member

Re: Night-service distinctive ring tone

I'm testing with two 7960 and two IP communicator.

286
Views
0
Helpful
10
Replies