Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

NM-CUE can not ping tftp

Hi,

I have a NM-CUE in a 2811 router, I need to upgrade software but  I can't ping anything on lan, I can only ping router interface.

Here are some show outputs:

2811#sh interfaces service-Engine 1/0
Service-Engine1/0 is up, line protocol is up
  Hardware is I82559FE, address is 001e.7a5f.80e8 (bia 001e.7a5f.80e8)
  Interface is unnumbered. Using address of Vlan10 (10.0.8.10)
  MTU 1500 bytes, BW 100000 Kbit/sec, DLY 100 usec,
     reliability 255/255, txload 1/255, rxload 1/255

2811#sh ip route

Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP
       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
       E1 - OSPF external type 1, E2 - OSPF external type 2
       i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
       ia - IS-IS inter area, * - candidate default, U - per-user static route
       o - ODR, P - periodic downloaded static route

Gateway of last resort is 10.0.8.20 to network 0.0.0.0

     10.0.0.0/8 is variably subnetted, 2 subnets, 2 masks
C       10.0.8.0/24 is directly connected, Vlan10
S       10.0.8.11/32 is directly connected, Service-Engine1/0

S*   0.0.0.0/0 [1/0] via 10.0.8.20

Thanks

hasrat

18 REPLIES

Re: NM-CUE can not ping tftp

Do you have a default gateway configured for the Service-Engine 1/0 interface? Such as:

interface Service-Engine1/0

service-module ip default-gateway 10.0.8.20

Can you post the rest of your configuration?

Hope this helps.

Brandon

New Member

Re: NM-CUE can not ping tftp

here is the related config:

!
interface Service-Engine1/0
ip unnumbered Vlan10
no ip redirects
no ip unreachables
no ip proxy-arp
service-module ip address 10.0.8.11 255.255.255.0
service-module ip default-gateway 10.0.8.10
!

!
interface Vlan10
ip address 10.0.8.10 255.255.255.0
no ip redirects
no ip unreachables
no ip proxy-arp
!
ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 10.0.8.20
ip route 10.0.8.11 255.255.255.255 Service-Engine1/0

!

thanks

hasrat

Re: NM-CUE can not ping tftp

Is the LAN address you're trying to ping on the same subnet (10.0.8.0/24)? Can you ping from the CME CLI to this address using VLAN10 as the source (ping

source 10.0.8.10)?

Brandon

New Member

Re: NM-CUE can not ping tftp

yes, here is the output:

2811#ping 10.0.8.20 source vlan 10

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.0.8.20, timeout is 2 seconds:
Packet sent with a source address of 10.0.8.10
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/4 ms
2811#

2811#ping 10.0.8.20 source 10.0.8.10

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.0.8.20, timeout is 2 seconds:
Packet sent with a source address of 10.0.8.10
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/4 ms
2811#

Re: NM-CUE can not ping tftp

But, you cannot ping 10.0.8.20 from the CUE CLI?

Brandon

New Member

Re: NM-CUE can not ping tftp

no, or any other address on lan.

Re: NM-CUE can not ping tftp

From 10.0.8.20, can you ping 10.0.8.11?

Brandon

New Member

Re: NM-CUE can not ping tftp

I can't, I reset CUE to factory default, still can't ping, when I do sh ip route I see 127.0.0.0 assigned to Loopback, I don't see it in config, how to get rid of it.

se-10-0-8-11> sh ip route
           DEST            GATE            MASK IFACE
       10.0.8.0         0.0.0.0   255.255.255.0 eth1
      127.0.0.0         0.0.0.0       255.0.0.0 lo
        0.0.0.0       10.0.8.10         0.0.0.0 eth1
se-10-0-8-11>

thanks

hasrat

Re: NM-CUE can not ping tftp

This looks correct. Is there another device that is the gateway for the rest of your LAN. Does it have a route for 10.0.8.11 going to 10.0.8.10?

Brandon

New Member

Re: NM-CUE can not ping tftp

no, it is sitting on my desk and .20 is my pc.

Re: NM-CUE can not ping tftp

Does your PC have a gateway of .10 or something different?

New Member

Re: NM-CUE can not ping tftp

it is .10 and I upgraded 2811 IOS, before attempting CUE

Re: NM-CUE can not ping tftp

Try putting a static route on your PC to 10.0.8.11.

Brandon

New Member

Re: NM-CUE can not ping tftp

I have tried that also, didn't help, how to see the loopback info ?

Re: NM-CUE can not ping tftp

Hmm. . .Definitely sounds like a routing issue somewhere. Not sure what loopback info you're looking for.

New Member

Re: NM-CUE can not ping tftp

loopback interface which shows up in sh ip route of cue:

se-10-0-8-11> sh ip route
           DEST            GATE            MASK   IFACE
       10.0.8.0         0.0.0.0   255.255.255.0   eth1
      127.0.0.0         0.0.0.0       255.0.0.0      lo

Re: NM-CUE can not ping tftp

Yes, this is normal. I have a CUE that also shows a loopback interface and works properly.

Brandon

New Member

Re: NM-CUE can not ping tftp

how to see the loopback information, I can't find any command to dispaly it.

928
Views
0
Helpful
18
Replies