Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
New Member

No dial tone and you cannot make a call

Sometimes a phone doesnot work no dial tone and you cannot call. when I look show voice call summary

it says

50/0/27 .1 - - - EFXS_W_SETUP_ACK_ONHOOK

I can solve that issue after restarting the call manager express... why is that happening ?

4 REPLIES
Hall of Fame Super Gold

Re: No dial tone and you cannot make a call

Which exact IOS version are you using ?

New Member

Re: No dial tone and you cannot make a call

Was there a fix to this? I have seen this on 12.4(9)T1 and a reboot of the router was the only fix.

This is what we saw:

PORT CODEC VAD VTSP STATE VPM STATE

============== ========= === ==================== ======================

0/0/0 - - - FXOLS_ONHOOK

0/0/1 - - - FXOLS_ONHOOK

0/0/2 - - - FXOLS_ONHOOK

0/0/3 - - - FXOLS_ONHOOK

0/1/0 - - - FXOLS_ONHOOK

0/1/1 - - - FXOLS_ONHOOK

0/1/2 - - - FXOLS_ONHOOK

0/1/3 - - - FXOLS_ONHOOK

50/0/1 .1 - - - EFXS_ONHOOK

50/0/2 .1 - - - EFXS_ONHOOK

50/0/3 .1 - - - EFXS_ONHOOK

50/0/4 .1 - - - EFXS_ONHOOK

50/0/5 .1 None - S_WAIT_RELEASE_RESP EFXS_W_SETUP_ACK_ONHOOK

50/0/5 .2 - - - EFXS_ONHOOK

50/0/6 .1 - - - EFXS_INIT

50/0/6 .2 - - - EFXS_INIT

50/0/7 .1 - - - EFXS_ONHOOK

50/0/7 .2 - - - EFXS_ONHOOK

50/0/8 .1 None - S_WAIT_RELEASE_RESP EFXS_W_SETUP_ACK_ONHOOK

50/0/8 .2 - - - EFXS_ONHOOK

50/0/9 .1 - - - EFXS_INIT

50/0/9 .2 - - - EFXS_INIT

50/0/10 .1 None - S_WAIT_RELEASE_RESP EFXS_W_SETUP_ACK_ONHOOK

50/0/10 .2 - - - EFXS_ONHOOK

50/0/11 .1 - - - EFXS_ONHOOK

50/0/12 .1 - - - EFXS_ONHOOK

50/0/13 .1 - - - EFXS_INIT

50/0/14 .1 - - - EFXS_INIT

50/0/15 .1 - - - EFXS_INIT

50/0/16 .1 - - - EFXS_ONHOOK

50/0/16 .2 - - - EFXS_ONHOOK

50/0/17 .1 - - - EFXS_ONHOOK

50/0/17 .2 - - - EFXS_ONHOOK

50/0/18 .1 - - - EFXS_ONHOOK

50/0/18 .2 - - - EFXS_ONHOOK

50/0/19 .1 - - - EFXS_INIT

50/0/20 .1 - - - EFXS_ONHOOK

50/0/20 .2 - - - EFXS_ONHOOK

50/0/21 .1 - - - EFXS_INIT

50/0/21 .2 - - - EFXS_INIT

50/0/23 .1 - - - EFXS_ONHOOK

50/0/24 .1 - - - EFXS_ONHOOK

50/0/25 .1 None - S_WAIT_RELEASE_RESP EFXS_W_SETUP_ACK_ONHOOK

50/0/25 .2 - - - EFXS_ONHOOK

50/0/26 .1 None - S_WAIT_RELEASE_RESP EFXS_W_SETUP_ACK_ONHOOK

50/0/26 .2 - - - EFXS_ONHOOK

50/0/27 .1 - - - EFXS_ONHOOK

50/0/27 .2 - - - EFXS_ONHOOK

50/0/30 .1 - - - EFXS_INIT

New Member

Re: No dial tone and you cannot make a call

yep reboot is the only way I could find.

New Member

Re: No dial tone and you cannot make a call

CSCsg74357 Bug Details
Call hung and stuck in active state, ephone-dn is stuck in on hook
Symptom:

Call hung and stuck in active state, so the ephone-dn is stuck in on hook.

Conditions:

intermittent. hard to recreate but happens a few times a week.

Workaround:

reload GW

Problem Description

-------------------------------

Some ephone-dn is stuck in on hook

Example:

=======

show ephone-dn summary

Port       Ch  DN STATE  VTSP STATE                    VPM STATE
50/0/10  1   DOWN         S_WAIT_RELEASE_RESP  EFXS_W_SETUP_ACK_ONHOOK
 
show call active voice brief
 shows the call as active but tx0/0 rx0/0 and there’s no actual call.
 
Inbound call get busy tone since the line is stucked, outbound call also not get through since it’s a single line.
 
Bug and workaround
------------------------------
The bug id is CSCsg74357
And right now the corrent version is 12.4.11XJ which is being affected, so we need to do the upgrade to provent it happen again.
While according to the bug, the temperate workaround is to reload router.
May need upgrade ios to 12.4(11)T2 or 12.4.22 and 12.4.24 main line.
1199
Views
0
Helpful
4
Replies
CreatePlease to create content