Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

No PSTN Calls using SRST on a Cisco 2851 IOS 15.1 CUCM 8.0.3

                   Hi All,

Can anyone help with this at all?

We have set up SRST fallback on our CUCM 8.0.3 in our lab. we have a both SIP and SCCP phone registered to CUCM and the endpoints fallback to the gateway as required and they can all call between each other.

The problem I have is there are no external calls able to be made.

The gateway is actually the MGCP gateway that CUCM uses to dial out to the E1 trunk via the BT ISDN30 and when CUCM is up I can make calls to PSTN all day long but the moment CUCM is down and the phones fallback to SRST its only internal calls.

Here is some of my configuration;

You can see here this is how call manager fallback is setup;

call-manager-fallback

max-conferences 8 gain -6

transfer-system full-consult

ip source-address 10.1.31.10 port 2000

max-ephones 20

max-dn 50

---------------------------------------

sip-ua

retry invite 3

retry register 3

----------------------------------------

voice service voip

allow-connections h323 to h323

allow-connections h323 to sip

allow-connections sip to h323

allow-connections sip to sip

sip

  bind control source-interface GigabitEthernet0/0

  bind media source-interface GigabitEthernet0/0

  registrar server expires max 600 min 60

!

voice class codec 1

codec preference 1 g711ulaw

codec preference 2 g711alaw

codec preference 3 g729br8

codec preference 4 g729r8

codec preference 5 g722-64

codec preference 6 g722-56

codec preference 7 g722-48

---------------------------------------

controller E1 0/3/0

pri-group timeslots 1-31 service mgcp

description E1 to PSTN for Cisco CUCM-8 BT Line

-------------------------------------------

interface Serial0/3/0:15

description Used for PSTN on CUCM8 PSTN

no ip address

encapsulation hdlc

isdn switch-type primary-net5

isdn incoming-voice voice

isdn bind-l3 ccm-manager

no cdp enable

dial-peer voice 10 pots

destination-pattern 0T

direct-inward-dial

port 0/3/0:15

forward-digits all

SBCISCOGW81#

SBCISCOGW81#

*Jun 22 10:40:14.647: //-1/xxxxxxxxxxxx/DPM/dpMatchPeersCore:

   Calling Number=01992706568, Called Number=01992706568, Peer Info Type=DIALPEER_INFO_SPEECH

*Jun 22 10:40:14.647: //-1/xxxxxxxxxxxx/DPM/dpMatchPeersCore:

   Match Rule=DP_MATCH_DEST; Called Number=01992706568

*Jun 22 10:40:14.647: //-1/xxxxxxxxxxxx/DPM/dpMatchPeersCore:

   Result=Success(0) after DP_MATCH_DEST

*Jun 22 10:40:14.647: //-1/xxxxxxxxxxxx/DPM/dpMatchSafModulePlugin:

   dialstring=01992706568, saf_enabled=1, saf_dndb_lookup=1, dp_result=0

*Jun 22 10:40:14.647: //-1/xxxxxxxxxxxx/DPM/dpMatchPeersMoreArg:

   Result=SUCCESS(0)

   List of Matched Outgoing Dial-peer(s):

     1: Dial-peer Tag=10

*Jun 22 10:40:14.647: //-1/xxxxxxxxxxxx/DPM/dpAssociateIncomingPeerCore:

   Calling Number=4313, Called Number=, Voice-Interface=0x0,

   Timeout=TRUE, Peer Encap Type=ENCAP_VOIP, Peer Search Type=PEER_TYPE_VOICE,

   Peer Info Type=DIALPEER_INFO_SPEECH

*Jun 22 10:40:14.647: //-1/xxxxxxxxxxxx/DPM/dpAssociateIncomingPeerCore:

   Result=Success(0) after DP_MATCH_ORIGINATE; Incoming Dial-peer=40002

*Jun 22 10:40:14.647: //-1/xxxxxxxxxxxx/DPM/dpMatchSafModulePlugin:

   dialstring=NULL, saf_enabled=0, saf_dndb_lookup=0, dp_result=0

*Jun 22 10:40:14.647: //-1/xxxxxxxxxxxx/DPM/dpAssociateIncomingPeerCore:

   Calling Number=4313, Called Number=, Voice-Interface=0x0,

   Timeout=TRUE, Peer Encap Type=ENCAP_VOIP, Peer Search Type=PEER_TYPE_VOICE,

   Peer Info Type=DIALPEER_INFO_SPEECH

*Jun 22 10:40:14.647: //-1/xxxxxxxxxxxx/DPM/dpAssociateIncomingPeerCore:

   Result=Success(0) after DP_MATCH_ORIGINATE; Incoming Dial-peer=40002

*Jun 22 10:40:14.647: //-1/xxxxxxxxxxxx/DPM/dpMatchSafModulePlugin:

   dialstring=NULL, saf_enabled=0, saf_dndb_lookup=0, dp_result=0

*Jun 22 10:40:14.647: //-1/7C34AD26849D/DPM/dpAssociateIncomingPeerCore:

   Calling Number=4313, Called Number=01992706568, Voice-Interface=0x0,

   Timeout=TRUE, Peer Encap Type=ENCAP_VOIP, Peer Search Type=PEER_TYPE_VOICE,

   Peer Info Type=DIALPEER_INFO_SPEECH

*Jun 22 10:40:14.647: //-1/7C34AD26849D/DPM/dpAssociateIncomingPeerCore:

   Result=Success(0) after DP_MATCH_ORIGINATE; Incoming Dial-peer=40002

*Jun 22 10:40:14.647: //-1/7C34AD26849D/DPM/dpMatchSafModulePlugin:

   dialstring=NULL, saf_enabled=0, saf_dndb_lookup=0, dp_result=0

*Jun 22 10:40:14.655: //-1/xxxxxxxxxxxx/DPM/dpMatchPeersCore:

   Calling Number=, Called Number=01992706568, Peer Info Type=DIALPEER_INFO_SPEECH

*Jun 22 10:40:14.655: //-1/xxxxxxxxxxxx/DPM/dpMatchPeersCore:

   Match Rule=DP_MATCH_DEST; Called Number=01992706568

*Jun 22 10:40:14.655: //-1/xxxxxxxxxxxx/DPM/dpMatchPeersCore:

   Result=Success(0) after DP_MATCH_DEST

*Jun 22 10:40:14.655: //-1/xxxxxxxxxxxx/DPM/dpMatchSafModulePlugin:

   dialstring=01992706568, saf_enabled=0, saf_dndb_lookup=1, dp_result=0

*Jun 22 10:40:14.655: //-1/xxxxxxxxxxxx/DPM/dpMatchPeersMoreArg:

   Result=SUCCESS(0)

   List of Matched Outgoing Dial-peer(s):

     1: Dial-peer Tag=10

*Jun 22 10:40:14.659: //-1/7C34AD26849D/DPM/dpMatchPeersCore:

   Calling Number=, Called Number=01992706568, Peer Info Type=DIALPEER_INFO_SPEECH

*Jun 22 10:40:14.659: //-1/7C34AD26849D/DPM/dpMatchPeersCore:

   Match Rule=DP_MATCH_DEST; Called Number=01992706568

*Jun 22 10:40:14.659: //-1/7C34AD26849D/DPM/dpMatchPeersCore:

   Result=Success(0) after DP_MATCH_DEST

*Jun 22 10:40:14.659: //-1/7C34AD26849D/DPM/dpMatchSafModulePlugin:

   dialstring=01992706568, saf_enabled=0, saf_dndb_lookup=1, dp_result=0

*Jun 22 10:40:14.659: //-1/7C34AD26849D/DPM/dpMatchPeersMoreArg:

   Result=SUCCESS(0)

   List of Matched Outgoing Dial-peer(s):

     1: Dial-peer Tag=10

*Jun 22 10:40:14.659: //-1/7C34AD26849D/DPM/dpMatchPeersCore:

   Calling Number=, Called Number=01992706568, Peer Info Type=DIALPEER_INFO_SPEECH

*Jun 22 10:40:14.659: //-1/7C34AD26849D/DPM/dpMatchPeersCore:

   Match Rule=DP_MATCH_DEST; Called Number=01992706568

*Jun 22 10:40:14.659: //-1/7C34AD26849D/DPM/dpMatchPeersCore:

   Result=Success(0) after DP_MATCH_DEST

*Jun 22 10:40:14.659: //-1/7C34AD26849D/DPM/dpMatchSafModulePlugin:

   dialstring=01992706568, saf_enabled=0, saf_dndb_lookup=1, dp_result=0

*Jun 22 10:40:14.659: //-1/7C34AD26849D/DPM/dpMatchPeersMoreArg:

   Result=SUCCESS(0)

   List of Matched Outgoing Dial-peer(s):

     1: Dial-peer Tag=10

*Jun 22 10:40:14.659: //-1/xxxxxxxxxxxx/DPM/dpMatchPeersCore:

   Calling Number=01992706568, Called Number=01992706568, Peer Info Type=DIALPEER_INFO_SPEECH

*Jun 22 10:40:14.659: //-1/xxxxxxxxxxxx/DPM/dpMatchPeersCore:

   Match Rule=DP_MATCH_DEST; Called Number=01992706568

*Jun 22 10:40:14.659: //-1/xxxxxxxxxxxx/DPM/dpMatchPeersCore:

   Result=Success(0) after DP_MATCH_DEST

*Jun 22 10:40:14.663: //-1/xxxxxxxxxxxx/DPM/dpMatchSafModulePlugin:

   dialstring=01992706568, saf_enabled=0, saf_dndb_lookup=1, dp_result=0

*Jun 22 10:40:14.663: //-1/xxxxxxxxxxxx/DPM/dpMatchPeersMoreArg:

   Result=SUCCESS(0)

   List of Matched Outgoing Dial-peer(s):

     1: Dial-peer Tag=10

*Jun 22 10:40:14.663: //-1/xxxxxxxxxxxx/DPM/dpAssociateIncomingPeerCore:

   Calling Number=01992706568, Called Number=, Voice-Interface=0x0,

   Timeout=TRUE, Peer Encap Type=ENCAP_VOIP, Peer Search Type=PEER_TYPE_VOICE,

   Peer Info Type=DIALPEER_INFO_SPEECH

*Jun 22 10:40:14.663: //-1/xxxxxxxxxxxx/DPM/dpAssociateIncomingPeerCore:

   Result=NO_MATCH(-1) After All Match Rules Attempt

*Jun 22 10:40:14.663: //-1/xxxxxxxxxxxx/DPM/dpMatchSafModulePlugin:

   dialstring=NULL, saf_enabled=0, saf_dndb_lookup=0, dp_result=-1

*Jun 22 10:40:14.663: //-1/xxxxxxxxxxxx/DPM/dpAssociateIncomingPeerCore:

   Calling Number=01992706568, Called Number=, Voice-Interface=0x0,

   Timeout=TRUE, Peer Encap Type=ENCAP_VOIP, Peer Search Type=PEER_TYPE_VOICE,

   Peer Info Type=DIALPEER_INFO_SPEECH

*Jun 22 10:40:14.663: //-1/xxxxxxxxxxxx/DPM/dpAssociateIncomingPeerCore:

   Result=NO_MATCH(-1) After All Match Rules Attempt

*Jun 22 10:40:14.663: //-1/xxxxxxxxxxxx/DPM/dpMatchSafModulePlugin:

   dialstring=NULL, saf_enabled=0, saf_dndb_lookup=0, dp_result=-1

*Jun 22 10:40:14.663: //-1/xxxxxxxxxxxx/DPM/dpMatchPeersCore:

   Calling Number=, Called Number=01992706568, Peer Info Type=DIALPEER_INFO_SPEECH

*Jun 22 10:40:14.663: //-1/xxxxxxxxxxxx/DPM/dpMatchPeersCore:

   Match Rule=DP_MATCH_DEST; Called Number=01992706568

*Jun 22 10:40:14.663: //-1/xxxxxxxxxxxx/DPM/dpMatchPeersCore:

   Result=Success(0) after DP_MATCH_DEST

*Jun 22 10:40:14.663: //-1/xxxxxxxxxxxx/DPM/dpMatchSafModulePlugin:

   dialstring=01992706568, saf_enabled=0, saf_dndb_lookup=1, dp_result=0

*Jun 22 10:40:14.663: //-1/xxxxxxxxxxxx/DPM/dpMatchPeersMoreArg:

   Result=SUCCESS(0)

   List of Matched Outgoing Dial-peer(s):

     1: Dial-peer Tag=10

*Jun 22 10:40:14.663: //-1/7C34AD26849D/DPM/dpMatchPeersCore:

   Calling Number=, Called Number=01992706568, Peer Info Type=DIALPEER_INFO_SPEECH

*Jun 22 10:40:14.663: //-1/7C34AD26849D/DPM/dpMatchPeersCore:

   Match Rule=DP_MATCH_DEST; Called Number=01992706568

*Jun 22 10:40:14.663: //-1/7C34AD26849D/DPM/dpMatchPeersCore:

   Result=Success(0) after DP_MATCH_DEST

*Jun 22 10:40:14.663: //-1/7C34AD26849D/DPM/dpMatchSafModulePlugin:

   dialstring=01992706568, saf_enabled=1, saf_dndb_lookup=1, dp_result=0

*Jun 22 10:40:14.663: //-1/7C34AD26849D/DPM/dpMatchPeersMoreArg:

   Result=SUCCESS(0)

   List of Matched Outgoing Dial-peer(s):

     1: Dial-peer Tag=10

interface Serial0/3/0:15
description Used for PSTN on CUCM8 PSTN
no ip address
encapsulation hdlc
isdn switch-type primary-net5
isdn incoming-voice voice
isdn bind-l3 ccm-manager
no cdp enable

-----------------------------------------

And then this Dial Peer;

dial-peer voice 10 pots
destination-pattern 0T
direct-inward-dial
port 0/3/0:15
forward-digits all

-----------------------------------------------------

This is the output from DEBUG VOICE DIALPEER when I dial the number from the phone;

It looks like it is matching the dial-peer but no call is being made;

SBCISCOGW81#

SBCISCOGW81#

*Jun 22 10:40:14.647: //-1/xxxxxxxxxxxx/DPM/dpMatchPeersCore:

   Calling Number=01992706568, Called Number=01992706568, Peer Info Type=DIALPEER_INFO_SPEECH

*Jun 22 10:40:14.647: //-1/xxxxxxxxxxxx/DPM/dpMatchPeersCore:

   Match Rule=DP_MATCH_DEST; Called Number=01992706568

*Jun 22 10:40:14.647: //-1/xxxxxxxxxxxx/DPM/dpMatchPeersCore:

   Result=Success(0) after DP_MATCH_DEST

*Jun 22 10:40:14.647: //-1/xxxxxxxxxxxx/DPM/dpMatchSafModulePlugin:

   dialstring=01992706568, saf_enabled=1, saf_dndb_lookup=1, dp_result=0

*Jun 22 10:40:14.647: //-1/xxxxxxxxxxxx/DPM/dpMatchPeersMoreArg:

   Result=SUCCESS(0)

   List of Matched Outgoing Dial-peer(s):

     1: Dial-peer Tag=10

*Jun 22 10:40:14.647: //-1/xxxxxxxxxxxx/DPM/dpAssociateIncomingPeerCore:

   Calling Number=4313, Called Number=, Voice-Interface=0x0,

   Timeout=TRUE, Peer Encap Type=ENCAP_VOIP, Peer Search Type=PEER_TYPE_VOICE,

   Peer Info Type=DIALPEER_INFO_SPEECH

*Jun 22 10:40:14.647: //-1/xxxxxxxxxxxx/DPM/dpAssociateIncomingPeerCore:

   Result=Success(0) after DP_MATCH_ORIGINATE; Incoming Dial-peer=40002

*Jun 22 10:40:14.647: //-1/xxxxxxxxxxxx/DPM/dpMatchSafModulePlugin:

   dialstring=NULL, saf_enabled=0, saf_dndb_lookup=0, dp_result=0

*Jun 22 10:40:14.647: //-1/xxxxxxxxxxxx/DPM/dpAssociateIncomingPeerCore:

   Calling Number=4313, Called Number=, Voice-Interface=0x0,

   Timeout=TRUE, Peer Encap Type=ENCAP_VOIP, Peer Search Type=PEER_TYPE_VOICE,

   Peer Info Type=DIALPEER_INFO_SPEECH

*Jun 22 10:40:14.647: //-1/xxxxxxxxxxxx/DPM/dpAssociateIncomingPeerCore:

   Result=Success(0) after DP_MATCH_ORIGINATE; Incoming Dial-peer=40002

*Jun 22 10:40:14.647: //-1/xxxxxxxxxxxx/DPM/dpMatchSafModulePlugin:

   dialstring=NULL, saf_enabled=0, saf_dndb_lookup=0, dp_result=0

*Jun 22 10:40:14.647: //-1/7C34AD26849D/DPM/dpAssociateIncomingPeerCore:

   Calling Number=4313, Called Number=01992706568, Voice-Interface=0x0,

   Timeout=TRUE, Peer Encap Type=ENCAP_VOIP, Peer Search Type=PEER_TYPE_VOICE,

   Peer Info Type=DIALPEER_INFO_SPEECH

*Jun 22 10:40:14.647: //-1/7C34AD26849D/DPM/dpAssociateIncomingPeerCore:

   Result=Success(0) after DP_MATCH_ORIGINATE; Incoming Dial-peer=40002

*Jun 22 10:40:14.647: //-1/7C34AD26849D/DPM/dpMatchSafModulePlugin:

   dialstring=NULL, saf_enabled=0, saf_dndb_lookup=0, dp_result=0

*Jun 22 10:40:14.655: //-1/xxxxxxxxxxxx/DPM/dpMatchPeersCore:

   Calling Number=, Called Number=01992706568, Peer Info Type=DIALPEER_INFO_SPEECH

*Jun 22 10:40:14.655: //-1/xxxxxxxxxxxx/DPM/dpMatchPeersCore:

   Match Rule=DP_MATCH_DEST; Called Number=01992706568

*Jun 22 10:40:14.655: //-1/xxxxxxxxxxxx/DPM/dpMatchPeersCore:

   Result=Success(0) after DP_MATCH_DEST

*Jun 22 10:40:14.655: //-1/xxxxxxxxxxxx/DPM/dpMatchSafModulePlugin:

   dialstring=01992706568, saf_enabled=0, saf_dndb_lookup=1, dp_result=0

*Jun 22 10:40:14.655: //-1/xxxxxxxxxxxx/DPM/dpMatchPeersMoreArg:

   Result=SUCCESS(0)

   List of Matched Outgoing Dial-peer(s):

     1: Dial-peer Tag=10

*Jun 22 10:40:14.659: //-1/7C34AD26849D/DPM/dpMatchPeersCore:

   Calling Number=, Called Number=01992706568, Peer Info Type=DIALPEER_INFO_SPEECH

*Jun 22 10:40:14.659: //-1/7C34AD26849D/DPM/dpMatchPeersCore:

   Match Rule=DP_MATCH_DEST; Called Number=01992706568

*Jun 22 10:40:14.659: //-1/7C34AD26849D/DPM/dpMatchPeersCore:

   Result=Success(0) after DP_MATCH_DEST

*Jun 22 10:40:14.659: //-1/7C34AD26849D/DPM/dpMatchSafModulePlugin:

   dialstring=01992706568, saf_enabled=0, saf_dndb_lookup=1, dp_result=0

*Jun 22 10:40:14.659: //-1/7C34AD26849D/DPM/dpMatchPeersMoreArg:

   Result=SUCCESS(0)

   List of Matched Outgoing Dial-peer(s):

     1: Dial-peer Tag=10

*Jun 22 10:40:14.659: //-1/7C34AD26849D/DPM/dpMatchPeersCore:

   Calling Number=, Called Number=01992706568, Peer Info Type=DIALPEER_INFO_SPEECH

*Jun 22 10:40:14.659: //-1/7C34AD26849D/DPM/dpMatchPeersCore:

   Match Rule=DP_MATCH_DEST; Called Number=01992706568

*Jun 22 10:40:14.659: //-1/7C34AD26849D/DPM/dpMatchPeersCore:

   Result=Success(0) after DP_MATCH_DEST

*Jun 22 10:40:14.659: //-1/7C34AD26849D/DPM/dpMatchSafModulePlugin:

   dialstring=01992706568, saf_enabled=0, saf_dndb_lookup=1, dp_result=0

*Jun 22 10:40:14.659: //-1/7C34AD26849D/DPM/dpMatchPeersMoreArg:

   Result=SUCCESS(0)

   List of Matched Outgoing Dial-peer(s):

     1: Dial-peer Tag=10

*Jun 22 10:40:14.659: //-1/xxxxxxxxxxxx/DPM/dpMatchPeersCore:

   Calling Number=01992706568, Called Number=01992706568, Peer Info Type=DIALPEER_INFO_SPEECH

*Jun 22 10:40:14.659: //-1/xxxxxxxxxxxx/DPM/dpMatchPeersCore:

   Match Rule=DP_MATCH_DEST; Called Number=01992706568

*Jun 22 10:40:14.659: //-1/xxxxxxxxxxxx/DPM/dpMatchPeersCore:

   Result=Success(0) after DP_MATCH_DEST

*Jun 22 10:40:14.663: //-1/xxxxxxxxxxxx/DPM/dpMatchSafModulePlugin:

   dialstring=01992706568, saf_enabled=0, saf_dndb_lookup=1, dp_result=0

*Jun 22 10:40:14.663: //-1/xxxxxxxxxxxx/DPM/dpMatchPeersMoreArg:

   Result=SUCCESS(0)

   List of Matched Outgoing Dial-peer(s):

     1: Dial-peer Tag=10

*Jun 22 10:40:14.663: //-1/xxxxxxxxxxxx/DPM/dpAssociateIncomingPeerCore:

   Calling Number=01992706568, Called Number=, Voice-Interface=0x0,

   Timeout=TRUE, Peer Encap Type=ENCAP_VOIP, Peer Search Type=PEER_TYPE_VOICE,

   Peer Info Type=DIALPEER_INFO_SPEECH

*Jun 22 10:40:14.663: //-1/xxxxxxxxxxxx/DPM/dpAssociateIncomingPeerCore:

   Result=NO_MATCH(-1) After All Match Rules Attempt

*Jun 22 10:40:14.663: //-1/xxxxxxxxxxxx/DPM/dpMatchSafModulePlugin:

   dialstring=NULL, saf_enabled=0, saf_dndb_lookup=0, dp_result=-1

*Jun 22 10:40:14.663: //-1/xxxxxxxxxxxx/DPM/dpAssociateIncomingPeerCore:

   Calling Number=01992706568, Called Number=, Voice-Interface=0x0,

   Timeout=TRUE, Peer Encap Type=ENCAP_VOIP, Peer Search Type=PEER_TYPE_VOICE,

   Peer Info Type=DIALPEER_INFO_SPEECH

*Jun 22 10:40:14.663: //-1/xxxxxxxxxxxx/DPM/dpAssociateIncomingPeerCore:

   Result=NO_MATCH(-1) After All Match Rules Attempt

*Jun 22 10:40:14.663: //-1/xxxxxxxxxxxx/DPM/dpMatchSafModulePlugin:

   dialstring=NULL, saf_enabled=0, saf_dndb_lookup=0, dp_result=-1

*Jun 22 10:40:14.663: //-1/xxxxxxxxxxxx/DPM/dpMatchPeersCore:

   Calling Number=, Called Number=01992706568, Peer Info Type=DIALPEER_INFO_SPEECH

*Jun 22 10:40:14.663: //-1/xxxxxxxxxxxx/DPM/dpMatchPeersCore:

   Match Rule=DP_MATCH_DEST; Called Number=01992706568

*Jun 22 10:40:14.663: //-1/xxxxxxxxxxxx/DPM/dpMatchPeersCore:

   Result=Success(0) after DP_MATCH_DEST

*Jun 22 10:40:14.663: //-1/xxxxxxxxxxxx/DPM/dpMatchSafModulePlugin:

   dialstring=01992706568, saf_enabled=0, saf_dndb_lookup=1, dp_result=0

*Jun 22 10:40:14.663: //-1/xxxxxxxxxxxx/DPM/dpMatchPeersMoreArg:

   Result=SUCCESS(0)

   List of Matched Outgoing Dial-peer(s):

     1: Dial-peer Tag=10

*Jun 22 10:40:14.663: //-1/7C34AD26849D/DPM/dpMatchPeersCore:

   Calling Number=, Called Number=01992706568, Peer Info Type=DIALPEER_INFO_SPEECH

*Jun 22 10:40:14.663: //-1/7C34AD26849D/DPM/dpMatchPeersCore:

   Match Rule=DP_MATCH_DEST; Called Number=01992706568

*Jun 22 10:40:14.663: //-1/7C34AD26849D/DPM/dpMatchPeersCore:

   Result=Success(0) after DP_MATCH_DEST

*Jun 22 10:40:14.663: //-1/7C34AD26849D/DPM/dpMatchSafModulePlugin:

   dialstring=01992706568, saf_enabled=1, saf_dndb_lookup=1, dp_result=0

*Jun 22 10:40:14.663: //-1/7C34AD26849D/DPM/dpMatchPeersMoreArg:

   Result=SUCCESS(0)

   List of Matched Outgoing Dial-peer(s):

     1: Dial-peer Tag=10

Any help or advice I've appreciate it very much so.

2 ACCEPTED SOLUTIONS

Accepted Solutions
VIP Super Bronze

No PSTN Calls using SRST on a Cisco 2851 IOS 15.1 CUCM 8.0.3

Usually you get this when you are in a glare condition. This mean that both side of the circuit, i.e you ane your provider are using the same channel allocation direction. Lets change your channel order and see if it helps.

conf t

interface Serial0/3/0:15

isdn bchan-number-order ascending.

Please send debug isdn q931 again.

Please rate useful posts

"For the love of God is broader than the measure of man's mind And the heart of the Eternal is most wonderfully kind"

Please rate all useful posts "The essence of christianity is not the enthronement but the obliteration of self --William Barclay"
VIP Super Bronze

No PSTN Calls using SRST on a Cisco 2851 IOS 15.1 CUCM 8.0.3

Ok you need to know which number to mach what DDI to.

to match 449861 to 4561 and 449860 to 4313, do this.

conf t

voice translation-rule 1

rule 1 /^449861/ /4561/

rule 2 /^449860/ /4313/

voice translation-profile SRSTIN

translate called 1

dial-peer voice 9999 pots

incoming called number .

direct-inward-dial

translation-profile incoming SRSTIN

 

Please rate useful posts

"For the love of God is broader than the measure of man's mind And the heart of the Eternal is most wonderfully kind"

Please rate all useful posts "The essence of christianity is not the enthronement but the obliteration of self --William Barclay"
15 REPLIES
VIP Super Bronze

Re: No PSTN Calls using SRST on a Cisco 2851 IOS 15.1 CUCM 8.0.3

Try this on your gateway

Conf t

application

global

service alternate default

Enable "debug isdn q931"

Do a test call and send the output of debug

Please rate useful posts

"For the love of God is broader than the measure of man's mind And the heart of the Eternal is most wonderfully kind"

Please rate all useful posts "The essence of christianity is not the enthronement but the obliteration of self --William Barclay"
New Member

No PSTN Calls using SRST on a Cisco 2851 IOS 15.1 CUCM 8.0.3

Thanks for your reply.

I have entered those commands but nothing has changed.

I have also enabled the debug isdn q931 but nothing is outputting.

I am getting the same output in debug voice dialpeer again too.

VIP Super Bronze

No PSTN Calls using SRST on a Cisco 2851 IOS 15.1 CUCM 8.0.3

Can you send a sh run ..please attach in a text file.

can you also send a "sh isdn status" while in SRST.

Please rate useful posts

"For the love of God is broader than the measure of man's mind And the heart of the Eternal is most wonderfully kind"

Please rate all useful posts "The essence of christianity is not the enthronement but the obliteration of self --William Barclay"
New Member

Re: No PSTN Calls using SRST on a Cisco 2851 IOS 15.1 CUCM 8.0.3

Hey,

Config is attached, the debug is at the bottom of the txt file.

Thanks

VIP Super Bronze

No PSTN Calls using SRST on a Cisco 2851 IOS 15.1 CUCM 8.0.3

Joe,

Looking at the output of sh isdn status.


SBCISCOGW81#sh isdn status
Global ISDN Switchtype = primary-net5

%Q.931 is backhauled to CCM MANAGER 0x0003 on DSL 0. Layer 3 output may not apply

ISDN Serial0/3/0:15 interface
        dsl 0, interface ISDN Switchtype = primary-net5
        L2 Protocol = Q.921 0x0000  L3 Protocol(s) = CCM MANAGER 0x0003
    Layer 1 Status:
        DEACTIVATED
    Layer 2 Status:
        TEI = 0, Ces = 1, SAPI = 0, State = TEI_ASSIGNED
    Layer 3 Status:
        0 Active Layer 3 Call(s)
    Active dsl 0 CCBs = 0
    The Free Channel Mask:  0x00000000
    Number of L2 Discards = 0, L2 Session ID = 0
    Total Allocated ISDN CCBs = 0

We can see that layer 1 is down in SRST.

Can you do this please. add the ff: command

ccm-manager fallback-mgcp.

I will suggest to put the system back to normal operation  after adding the command and then simualte SRST again

Configure

Please rate useful posts

"For the love of God is broader than the measure of man's mind And the heart of the Eternal is most wonderfully kind"

Please rate all useful posts "The essence of christianity is not the enthronement but the obliteration of self --William Barclay"
New Member

Re: No PSTN Calls using SRST on a Cisco 2851 IOS 15.1 CUCM 8.0.3

Hey,

Ok so I still am unable to make external calls but since adding that ccm-manager fallback-mgcp the layer 1 on the PRI is active now

This is what I get what I do debug isdn Q921

SBCISCOGW81#

*Jun 22 12:09:53.547: ISDN Se0/3/0:15 Q921: User RX <- RRp sapi=0 tei=0 nr=4

*Jun 22 12:09:53.547: ISDN Se0/3/0:15 Q921: User TX -> RRf sapi=0 tei=0 nr=4

*Jun 22 12:09:57.131: ISDN Se0/3/0:15 Q921: User TX -> INFO sapi=0 tei=0, ns=4 nr=4

*Jun 22 12:09:57.155: ISDN Se0/3/0:15 Q921: User RX <- RR sapi=0 tei=0 nr=5

*Jun 22 12:09:57.207: ISDN Se0/3/0:15 Q921: User RX <- INFO sapi=0 tei=0, ns=4 nr=5

*Jun 22 12:09:57.211: ISDN Se0/3/0:15 Q921: User TX -> RR sapi=0 tei=0 nr=5

and this is debug isdn q931

*Jun 22 12:13:03.871: ISDN Se0/3/0:15 Q931: Applying typeplan for sw-type 0x12 is 0x0 0x1, Calling num 4313

*Jun 22 12:13:03.871: ISDN Se0/3/0:15 Q931: Sending SETUP  callref = 0x0086 callID = 0x8007 switch = primary-net5 interface = User

*Jun 22 12:13:03.871: ISDN Se0/3/0:15 Q931: TX -> SETUP pd = 8  callref = 0x0086

        Bearer Capability i = 0x8090A3

                Standard = CCITT

                Transfer Capability = Speech

                Transfer Mode = Circuit

                Transfer Rate = 64 kbit/s

        Channel ID i = 0xA9839F

                Exclusive, Channel 31

        Calling Party Number i = 0x0180, '4313'

                Plan:ISDN, Type:Unknown

        Called Party Number i = 0x81, '01992706568'

                Plan:ISDN, Type:Unknown

*Jun 22 12:13:03.951: ISDN Se0/3/0:15 Q931: RX <- RELEASE_COMP pd = 8  callref = 0x8086

        Cause i = 0x82AC - Requested circuit/channel not available

attached is the output from debug voice ccapi.

VIP Super Bronze

No PSTN Calls using SRST on a Cisco 2851 IOS 15.1 CUCM 8.0.3

Usually you get this when you are in a glare condition. This mean that both side of the circuit, i.e you ane your provider are using the same channel allocation direction. Lets change your channel order and see if it helps.

conf t

interface Serial0/3/0:15

isdn bchan-number-order ascending.

Please send debug isdn q931 again.

Please rate useful posts

"For the love of God is broader than the measure of man's mind And the heart of the Eternal is most wonderfully kind"

Please rate all useful posts "The essence of christianity is not the enthronement but the obliteration of self --William Barclay"
New Member

Re: No PSTN Calls using SRST on a Cisco 2851 IOS 15.1 CUCM 8.0.3

Thank you very much this now dials outside

This is the debug output;

*Jun 22 12:33:19.911: ISDN Se0/3/0:15 Q931: Applying typeplan for sw-type 0x12 is 0x0 0x1, Calling num 4313

*Jun 22 12:33:19.911: ISDN Se0/3/0:15 Q931: Sending SETUP  callref = 0x0089 callID = 0x800A switch = primary-net5 interface = User

*Jun 22 12:33:19.911: ISDN Se0/3/0:15 Q931: TX -> SETUP pd = 8  callref = 0x0089

        Bearer Capability i = 0x8090A3

                Standard = CCITT

                Transfer Capability = Speech

                Transfer Mode = Circuit

                Transfer Rate = 64 kbit/s

        Channel ID i = 0xA98381

                Exclusive, Channel 1

        Calling Party Number i = 0x0180, '4313'

                Plan:ISDN, Type:Unknown

        Called Party Number i = 0x81, '01992706568'

                Plan:ISDN, Type:Unknown

*Jun 22 12:33:20.103: ISDN Se0/3/0:15 Q931: RX <- CALL_PROC pd = 8  callref = 0x8089

        Channel ID i = 0xA98381

                Exclusive, Channel 1

*Jun 22 12:33:20.351: ISDN Se0/3/0:15 Q931: RX <- ALERTING pd = 8  callref = 0x8089

*Jun 22 12:33:32.011: ISDN Se0/3/0:15 Q931: RX <- CONNECT pd = 8  callref = 0x8089

        Progress Ind i = 0x8582 - Destination address is non-ISDN

*Jun 22 12:33:32.011: %ISDN-6-CONNECT: Interface Serial0/3/0:0 is now connected to 01992706568 N/A

*Jun 22 12:33:32.011: ISDN Se0/3/0:15 Q931: TX -> CONNECT_ACK pd = 8  callref = 0x0089

*Jun 22 12:33:38.595: ISDN Se0/3/0:15 Q931: RX <- DISCONNECT pd = 8  callref = 0x8089

        Cause i = 0x8590 - Normal call clearing

        Progress Ind i = 0x8288 - In-band info or appropriate now available

*Jun 22 12:33:38.595: %ISDN-6-DISCONNECT: Interface Serial0/3/0:0  disconnected from 01992706568 , call lasted 6 seconds

*Jun 22 12:33:38.595: ISDN Se0/3/0:15 Q931: call_disc: PI received in disconnect; Postpone sending RELEASE for callid 0x800A

*Jun 22 12:33:46.155: ISDN Se0/3/0:15 Q931: TX -> RELEASE pd = 8  callref = 0x0089

*Jun 22 12:33:46.211: ISDN Se0/3/0:15 Q931: RX <- RELEASE_COMP pd = 8  callref = 0x8089

*Jun 22 12:33:19.911: ISDN Se0/3/0:15 Q931: Applying typeplan for sw-type 0x12 is 0x0 0x1, Calling num 4313

*Jun 22 12:33:19.911: ISDN Se0/3/0:15 Q931: Sending SETUP  callref = 0x0089 callID = 0x800A switch = primary-net5 interface = User

*Jun 22 12:33:19.911: ISDN Se0/3/0:15 Q931: TX -> SETUP pd = 8  callref = 0x0089

        Bearer Capability i = 0x8090A3

                Standard = CCITT

                Transfer Capability = Speech

                Transfer Mode = Circuit

                Transfer Rate = 64 kbit/s

        Channel ID i = 0xA98381

                Exclusive, Channel 1

        Calling Party Number i = 0x0180, '4313'

                Plan:ISDN, Type:Unknown

        Called Party Number i = 0x81, '01992706568'

                Plan:ISDN, Type:Unknown

*Jun 22 12:33:20.103: ISDN Se0/3/0:15 Q931: RX <- CALL_PROC pd = 8  callref = 0x8089

        Channel ID i = 0xA98381

                Exclusive, Channel 1

*Jun 22 12:33:20.351: ISDN Se0/3/0:15 Q931: RX <- ALERTING pd = 8  callref = 0x8089

*Jun 22 12:33:32.011: ISDN Se0/3/0:15 Q931: RX <- CONNECT pd = 8  callref = 0x8089

        Progress Ind i = 0x8582 - Destination address is non-ISDN

*Jun 22 12:33:32.011: %ISDN-6-CONNECT: Interface Serial0/3/0:0 is now connected to 01992706568 N/A

*Jun 22 12:33:32.011: ISDN Se0/3/0:15 Q931: TX -> CONNECT_ACK pd = 8  callref = 0x0089

*Jun 22 12:33:38.595: ISDN Se0/3/0:15 Q931: RX <- DISCONNECT pd = 8  callref = 0x8089

        Cause i = 0x8590 - Normal call clearing

        Progress Ind i = 0x8288 - In-band info or appropriate now available

*Jun 22 12:33:38.595: %ISDN-6-DISCONNECT: Interface Serial0/3/0:0  disconnected from 01992706568 , call lasted 6 seconds

*Jun 22 12:33:38.595: ISDN Se0/3/0:15 Q931: call_disc: PI received in disconnect; Postpone sending RELEASE for callid 0x800A

*Jun 22 12:33:46.155: ISDN Se0/3/0:15 Q931: TX -> RELEASE pd = 8  callref = 0x0089

*Jun 22 12:33:46.211: ISDN Se0/3/0:15 Q931: RX <- RELEASE_COMP pd = 8  callref = 0x8089

Super Bronze

Re: No PSTN Calls using SRST on a Cisco 2851 IOS 15.1 CUCM 8.0.3

Hi Guys

The other common cause of 'Requested circuit/channel not available' is that you may have provisioned a fractional E1. For example 8 or 16 channels... in that scenario you have only the first x channels so the default of using the top channel for outbound isn't suitable.

Regards

Aaron Harrison

Principal Engineer at Logicalis UK

Please rate helpful posts...

Aaron Please remember to rate helpful posts to identify useful responses, and mark 'Answered' if appropriate!
New Member

Re: No PSTN Calls using SRST on a Cisco 2851 IOS 15.1 CUCM 8.0.3

Oh yes I totally understand now! Well many thanks for your help both of you.

What would I need to do to configure this to accept incomming calls to a DDI?

Joe

VIP Super Bronze

No PSTN Calls using SRST on a Cisco 2851 IOS 15.1 CUCM 8.0.3

In SRST?

You need to know how many digit your telco is sending and then configure translation profile to change the sent DDI to internal extension. Do a test call for incoming DDI. Send the output of debug isdn q931. Let me know what the internal number the DDI should macth and we can configure a xlation rule to match it

Please rate useful posts

"For the love of God is broader than the measure of man's mind And the heart of the Eternal is most wonderfully kind"

Please rate all useful posts "The essence of christianity is not the enthronement but the obliteration of self --William Barclay"
New Member

Re: No PSTN Calls using SRST on a Cisco 2851 IOS 15.1 CUCM 8.0.3

Yes my friend in SRST mode.

Outbound calls are working lovely now

This is the output when I try to dial inbound; The called party number is highlighted in bold text. the DDI's I am using are 4561, and 4313. 449860 is one DDI from the service provider and 449861 isd another. altogether I think we have 8 of them for testing in our labs but we will only use 449860 and 449861. with the area code the whole number will be 01992 44986X

*Jun 22 13:05:10.375: ISDN Se0/3/0:15 Q931: RX <- SETUP pd = 8  callref = 0x0001

        Sending Complete

        Bearer Capability i = 0x9090A3

                Standard = CCITT

                Transfer Capability = 3.1kHz Audio

                Transfer Mode = Circuit

                Transfer Rate = 64 kbit/s

        Channel ID i = 0xA98381

                Exclusive, Channel 1

        Progress Ind i = 0x8583 - Origination address is non-ISDN

        Calling Party Number i = 0x2181, '1992706568'

                Plan:ISDN, Type:National

        Called Party Number i = 0x81, '449860'

                Plan:ISDN, Type:Unknown

*Jun 22 13:05:10.375: ISDN Se0/3/0:15 Q931: Received SETUP  callref = 0x8001 callID = 0x0002 switch = primary-net5 interface = User

*Jun 22 13:05:10.391: ISDN Se0/3/0:15 Q931: TX -> CALL_PROC pd = 8  callref = 0x8001

        Channel ID i = 0xA98381

                Exclusive, Channel 1

*Jun 22 13:05:10.391: ISDN Se0/3/0:15 Q931: TX -> DISCONNECT pd = 8  callref = 0x8001

        Cause i = 0x8081 - Unallocated/unassigned number

*Jun 22 13:05:10.575: ISDN Se0/3/0:15 Q931: RX <- RELEASE pd = 8  callref = 0x0001

*Jun 22 13:05:10.575: ISDN Se0/3/0:15 Q931: TX -> RELEASE_COMP pd = 8  callref = 0x8001

Many thanks for your help so far

VIP Super Bronze

No PSTN Calls using SRST on a Cisco 2851 IOS 15.1 CUCM 8.0.3

Ok you need to know which number to mach what DDI to.

to match 449861 to 4561 and 449860 to 4313, do this.

conf t

voice translation-rule 1

rule 1 /^449861/ /4561/

rule 2 /^449860/ /4313/

voice translation-profile SRSTIN

translate called 1

dial-peer voice 9999 pots

incoming called number .

direct-inward-dial

translation-profile incoming SRSTIN

 

Please rate useful posts

"For the love of God is broader than the measure of man's mind And the heart of the Eternal is most wonderfully kind"

Please rate all useful posts "The essence of christianity is not the enthronement but the obliteration of self --William Barclay"
New Member

Re: No PSTN Calls using SRST on a Cisco 2851 IOS 15.1 CUCM 8.0.3

Thank you very much Sir,

this is now working how I want it to. really, many thanks for your help you have been fantastic!

VIP Super Bronze

No PSTN Calls using SRST on a Cisco 2851 IOS 15.1 CUCM 8.0.3

Hey Joe, No sirs here. We are all buddies! Glad to help.

Please rate useful posts

"For the love of God is broader than the measure of man's mind And the heart of the Eternal is most wonderfully kind"

Please rate all useful posts "The essence of christianity is not the enthronement but the obliteration of self --William Barclay"
2318
Views
5
Helpful
15
Replies