Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

no register e164 with IP Phone ?

Hi,

Is it possible to specify dial-peer voip to unregistered its E.164-ID onto the GK ?

Wit pots there is no register e164 command but nothing with voip dial-peer.

Bregards

Olivier

1 ACCEPTED SOLUTION

Accepted Solutions
Cisco Employee

Re: no register e164 with IP Phone ?

Hi Olivier,

The no-reg keyword used with the number command on the ephone-dn should do it.

Also try executing a show telephony-service dial-peer command. You should notice that that dial-peers created based on your phones registering with CME are actually POTS dial peers.

Regards,

Michael.

6 REPLIES
Cisco Employee

Re: no register e164 with IP Phone ?

Hello Olivier,

It is not possible because voip dial-peers should not register E.164-ID to the gatekeeper. Are you finding otherwise?

New Member

Re: no register e164 with IP Phone ?

You're true mowuor.

in fact this is the ephone that are configured on my CME that are registered on my GK.

any idea ?

Olivier

Cisco Employee

Re: no register e164 with IP Phone ?

Hi Olivier,

The no-reg keyword used with the number command on the ephone-dn should do it.

Also try executing a show telephony-service dial-peer command. You should notice that that dial-peers created based on your phones registering with CME are actually POTS dial peers.

Regards,

Michael.

Bronze

Re: no register e164 with IP Phone ?

Hi Olivier,

The purpose of the "no register e164" command on a pots dial-peer is to de-register the E.164 number of a directly connected FXS device from the GK. If you have a directly connected IP phone (if you are using SRST or CME) you can deregister the E164 number from a gatekeeper as follows.

conf t

ephone-dn x

number xxxx no-reg primary

Hope this helps, please rate if it does.

Regards,

Dave

New Member

Re: no register e164 with IP Phone ?

Right, but how it's possible to suppress E 164 GK registering from all the pots dial-peer (20002,20004,20006 and so on...) ??

CCME#show telephony-service dial-peer

dial-peer voice 20001 pots

destination-pattern 1001$

no e164 registration

huntstop

progress_ind setup enable 3

port 50/0/1

dial-peer voice 20002 pots

destination-pattern 604701001$

huntstop

progress_ind setup enable 3

port 50/0/1

dial-peer voice 20003 pots

destination-pattern 1002$

no e164 registration

huntstop

progress_ind setup enable 3

port 50/0/2

dial-peer voice 20004 pots

destination-pattern 604701002$

huntstop

progress_ind setup enable 3

port 50/0/2

dial-peer voice 20005 pots

destination-pattern 1003$

no e164 registration

huntstop

progress_ind setup enable 3

port 50/0/3

dial-peer voice 20006 pots

destination-pattern 604701003$

huntstop

progress_ind setup enable 3

port 50/0/3

dial-peer voice 20007 pots

destination-pattern 1004$

no e164 registration

huntstop

progress_ind setup enable 3

port 50/0/4

dial-peer voice 20008 pots

destination-pattern 604701004$

huntstop

progress_ind setup enable 3

port 50/0/4

dial-peer voice 20011 pots

destination-pattern 1005$

no e164 registration

huntstop

progress_ind setup enable 3

port 50/0/5

dial-peer voice 20012 pots

destination-pattern 604701005$

huntstop

progress_ind setup enable 3

port 50/0/5

dial-peer voice 20013 pots

destination-pattern 1095$

no e164 registration

huntstop

progress_ind setup enable 3

port 50/0/95

dial-peer voice 20014 pots

destination-pattern 604701095$

huntstop

progress_ind setup enable 3

port 50/0/95

dial-peer voice 20015 pots

destination-pattern 1096$

no e164 registration

huntstop

progress_ind setup enable 3

port 50/0/96

dial-peer voice 20016 pots

destination-pattern 604701096$

huntstop

progress_ind setup enable 3

port 50/0/96

dial-peer voice 20017 pots

destination-pattern 1097$

no e164 registration

huntstop

progress_ind setup enable 3

port 50/0/97

dial-peer voice 20018 pots

destination-pattern 604701097$

huntstop

progress_ind setup enable 3

port 50/0/97

dial-peer voice 20019 pots

destination-pattern 1098$

no e164 registration

huntstop

progress_ind setup enable 3

port 50/0/98

dial-peer voice 20020 pots

destination-pattern 604701098$

huntstop

progress_ind setup enable 3

port 50/0/98

dial-peer voice 20021 pots

destination-pattern 1099$

no e164 registration

huntstop

progress_ind setup enable 3

port 50/0/99

dial-peer voice 20022 pots

destination-pattern 604701099$

huntstop

progress_ind setup enable 3

port 50/0/99

CCME#

New Member

Re: no register e164 with IP Phone ?

it's ok I have found

telephony-service

dialplan-pattern 1 60470.... extension-length 4 no-reg

thanks

Olivier

1728
Views
10
Helpful
6
Replies