Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

No voice-port 2821 w/HWIC-1CE1T1-PRI and PVDM2-32

I am in the middle of setting up a voice gateway and when I try to set up the voice-port, I get "Invalid input".

Applicable config:

controller T1 0/0/0

framing esf

linecode b8zs

cablelength short 110

pri-group timeslots 1-24

interface Serial0/0/0:23

no ip address

encapsulation hdlc

isdn switch-type primary-dms100

isdn incoming-voice voice

isdn map address . plan isdn type national

isdn send-alerting

isdn outgoing ie redirecting-number

isdn outgoing ie high-layer-compat

isdn outgoing ie user-user

no cdp enable

!

Show inventory output:

NAME: "2821 chassis", DESCR: "2821 chassis"

PID: CISCO2821 , VID: V04 , SN: FTX1222A0N3

NAME: "1 port channelized and PRI T1/E1 HWIC on Slot 0 SubSlot 0", DESCR: "1 port channelized and PRI T1/E1 HWIC"

PID: HWIC-1CE1T1-PRI , VID: V01 , SN: FOC12043N5W

NAME: "PVDMII DSP SIMM with Two DSPs on Slot 0 SubSlot 4", DESCR: "PVDMII DSP SIMM with Two DSPs"

PID: PVDM2-32 , VID: V01 , SN: FOC12161HE7

I've been trying to figure this out and I've hit a brick wall. I thought I had all the pieces...

Thank you

1 ACCEPTED SOLUTION

Accepted Solutions
Hall of Fame Super Red

Re: No voice-port 2821 w/HWIC-1CE1T1-PRI and PVDM2-32

Hi Richard,

The problem here is that the HWIC-1CE1T1-PRI does not support Voice PRI's. :( You will want to use a VWIC.

http://www.cisco.com/en/US/prod/collateral/modules/ps2797/product_data_sheet0900aecd80710c88_ps5949_Products_Data_Sheet.html

Hope this helps! Sorry man,

Rob

5 REPLIES
Hall of Fame Super Gold

Re: No voice-port 2821 w/HWIC-1CE1T1-PRI and PVDM2-32

Show ver? You might be running an image w/o voice support. E.g. ipbase.

Hope this helps, please rate post if it does!

Hall of Fame Super Red

Re: No voice-port 2821 w/HWIC-1CE1T1-PRI and PVDM2-32

Hi Richard,

The problem here is that the HWIC-1CE1T1-PRI does not support Voice PRI's. :( You will want to use a VWIC.

http://www.cisco.com/en/US/prod/collateral/modules/ps2797/product_data_sheet0900aecd80710c88_ps5949_Products_Data_Sheet.html

Hope this helps! Sorry man,

Rob

Hall of Fame Super Gold

Re: No voice-port 2821 w/HWIC-1CE1T1-PRI and PVDM2-32

Oh, I misread that, I "wanted" to read VWIC and so I did :[

Of course Rob is correct. So 5 points for him here.

Hall of Fame Super Red

Re: No voice-port 2821 w/HWIC-1CE1T1-PRI and PVDM2-32

Hi Paolo,

You are most kind! Thanks for this nice vote my friend.

Rock On!

Huff

New Member

Re: No voice-port 2821 w/HWIC-1CE1T1-PRI and PVDM2-32

Wow, thank you. Not great news but I figured there had to be a good reason.

Thank you all,

Richard

584
Views
5
Helpful
5
Replies