08-17-2009 07:03 AM - edited 03-15-2019 07:24 PM
Hi,
I am using CM 7.0 with a QSIG to a Siemens Realitis I have a problem with user busy status in the hybrid environment, when a Cisco phone calls a Siemens phone whilst it is in use you get engaged tone as expected, however the reverse gives number unobtainable. I have completed a debug isdn q931 below -
Cisco to Siemens
Aug 17 13:04:15.268: ISDN Se0/0/0:15 Q931: TX -> SETUP pd = 8 callref = 0x6E77
Sending Complete
Bearer Capability i = 0x8090A3
Standard = CCITT
Transfer Capability = Speech
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA98381
Exclusive, Channel 1
Facility i = 0x91AA06800100820100A11602010006042B0C0900800B4A616D6573204E6F626273
Calling Party Number i = 0x0081, '3533'
Plan:Unknown, Type:Unknown
Called Party Number i = 0x80, '7004909'
Plan:Unknown, Type:Unknown
Aug 17 13:04:15.384: ISDN Se0/0/0:15 Q931: RX <- CALL_PROC pd = 8 callref = 0xEE77
Channel ID i = 0xA98381
Exclusive, Channel 1
DEVG01#
Aug 17 13:04:15.620: ISDN Se0/0/0:15 Q931: RX <- DISCONNECT pd = 8 callref = 0xEE77
Cause i = 0x8191 - User busy
Aug 17 13:04:15.660: ISDN Se0/0/0:15 Q931: TX -> RELEASE pd = 8 callref = 0x6E77
Aug 17 13:04:15.788: ISDN Se0/0/0:15 Q931: RX <- RELEASE_COMP pd = 8 callref = 0xEE77
Siemens to Cisco
Aug 17 13:04:52.304: ISDN Se0/0/0:15 Q931: RX <- SETUP pd = 8 callref = 0x5174
Bearer Capability i = 0x8090A3
Standard = CCITT
Transfer Capability = Speech
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA18381
Preferred, Channel 1
Calling Party Number i = 0x0083, '7004909'
Plan:Unknown, Type:Unknown
Called Party Number i = 0x80, '3589'
Plan:Unknown, Type:Unknown
Low Layer Compat i = 0x8090A3
Locking Shift to Codeset 4
Codeset 4 IE 0x31 i = 0x82
Locking Shift to Codeset 5
Codeset 5 IE 0x32 i = 0x81
DEVG01#
Aug 17 13:04:52.316: ISDN Se0/0/0:15 Q931: TX -> CALL_PROC pd = 8 callref = 0xD174
Channel ID i = 0xA98381
Exclusive, Channel 1
Aug 17 13:04:52.524: ISDN Se0/0/0:15 Q931: TX -> DISCONNECT pd = 8 callref = 0xD174
Cause i = 0x8191 - User busy
Facility i = 0x91AA06800100820100A11502010306042B0C0903800A4D61726B204172626F6E
Aug 17 13:04:52.712: ISDN Se0/0/0:15 Q931: RX <- RELEASE pd = 8 callref = 0x5174
Cause i = 0x81E31C - Information element not implemented
Aug 17 13:04:52.740: ISDN Se0/0/0:15 Q931: TX -> RELEASE_COMP pd = 8 callref = 0xD174
Any ideas would be gratefully received.
Regards
James
08-17-2009 07:43 AM
Cisco dis disconnecting by user busy;
Aug 17 13:04:52.524: ISDN Se0/0/0:15 Q931: TX -> DISCONNECT pd = 8 callref = 0xD174
Cause i = 0x8191 - User busy
Facility i = 0x91AA06800100820100A11502010306042B0C0903800A4D61726B204172626F6E
Then PBX complains about that IE, that should not affect the fact Cisco has disconnected correctly, however yuo can prevent the cisco to sen facility IE under interface "no isdn ie outgoig facility".
08-19-2009 06:30 AM
Tried it still didnt work..
!
interface Serial0/3/0:15
no ip address
encapsulation hdlc
isdn switch-type primary-qsig
isdn incoming-voice voice
isdn bind-l3 ccm-manager
isdn bchan-number-order ascending
no isdn outgoing ie facility
no cdp enable
!
The isdn q931 debug output
*Aug 19 15:32:23: ISDN Se0/3/0:15 Q931: RX <- SETUP pd = 8 callref = 0x0028
Bearer Capability i = 0x8090A3
Standard = CCITT
Transfer Capability = Speech
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA98381
Exclusive, Channel 1
Calling Party Number i = 0x00A3, '5808'
Plan:Unknown, Type:Unknown
Called Party Number i = 0x80, '7771'
Plan:Unknown, Type:Unknown
Low Layer Compat i = 0x8090A3
Locking Shift to Codeset 4
Codeset 4 IE 0x31 i = 0x80
Locking Shift to Codeset 5
Codeset 5 IE 0x32 i = 0x81
ocgr22#
*Aug 19 15:32:23: ISDN Se0/3/0:15 Q931: TX -> CALL_PROC pd = 8 callref = 0x8028
Channel ID i = 0xA98381
Exclusive, Channel 1
*Aug 19 15:32:23: ISDN Se0/3/0:15 Q931: TX -> DISCONNECT pd = 8 callref = 0x8028
Cause i = 0x8191 - User busy
Facility i = 0x9FAA06800100820100A1080201030201038400
*Aug 19 15:32:23: ISDN Se0/3/0:15 Q931: RX <- RELEASE pd = 8 callref = 0x0028
Cause i = 0x81E31C - Information element not implemented
*Aug 19 15:32:23: ISDN Se0/3/0:15 Q931: TX -> RELEASE_COMP pd = 8 callref = 0x8028
ocgr22#
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: