Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

only send 4 digits to PSTN

Hi,

When I place a call to PSTM throught a BRI port, in a CME 8 the telephone try to place that call sending only 4 digits, when I am introducing the digits, in the 4º digits stop and try to send the call.

Progress Ind i = 0x8183 - Origination address is non-ISDN

      Calling Party Number i = 0x0080, '4110'

                Plan:Unknown, Type:Unknown

        Called Party Number i = 0x80, '630'

                Plan:Unknown, Type:Unknown

        Sending Complete

Jul 18 13:20:52.155: ISDN BR0/0/0 Q931: RX <- CALL_PROC pd = 8  callref = 0xC4

        Channel ID i = 0x89

                Exclusive, B1

Jul 18 13:20:52.175: ISDN BR0/0/0 Q931: RX <- PROGRESS pd = 8  callref = 0xC4

        Cause i = 0x829F - Normal, unspecified

        Progress Ind i = 0x8A81 - Call not end-to-end ISDN, may have in-band info

        Progress Ind i = 0x8A88 - In-band info or appropriate now available

Jul 18 13:20:56.139: ISDN BR0/0/0 Q931: TX -> DISCONNECT pd = 8  callref = 0x44

I have checked interdigits timeout, and it is set to 5, dial-peer are correctly configurated

RouterVallecas#sh dialplan number 0630112233
Macro Exp.: 0630112233

VoiceEncapPeer210
        peer type = voice, system default peer = FALSE, information type = voice,
        description = `Moviles',
        tag = 210, destination-pattern = `06........',
        voice reg type = 0, corresponding tag = 0,
        allow watch = FALSE
        answer-address = `', preference=1,
        CLID Restriction = None
        CLID Network Number = `'
        CLID Second Number sent
        CLID Override RDNIS = disabled,
        rtp-ssrc mux = system
        source carrier-id = `', target carrier-id = `',
        source trunk-group-label = `',  target trunk-group-label = `',
        numbering Type = `unknown'
        group = 210, Admin state is up, Operation state is up,
        Outbound state is up,
        incoming called-number = `', connections/maximum = 0/unlimited,
        DTMF Relay = disabled,
        URI classes:
            Destination =
        huntstop = disabled,
        in bound application associated: 'DEFAULT'

dial-peer voice 210 pots

description Moviles

preference 1

destination-pattern 06........

port 0/0/0

forward-digits 9

If I try to place a call to other number always is the same result, 091....... only place 4 digits, and so on.

Any idea where could be the problem?

Thanks!!

Everyone's tags (3)
1 ACCEPTED SOLUTION

Accepted Solutions
Hall of Fame Super Gold

Re: only send 4 digits to PSTN

There is another dial-peer then.

try 'show dialplan number 0611 timeout'

4 REPLIES
New Member

only send 4 digits to PSTN

Hi Ivan

Please show the whole configuration. Might be, that you are matching a translation rule.

Cheers

Peter

Hall of Fame Super Gold

Re: only send 4 digits to PSTN

There is another dial-peer then.

try 'show dialplan number 0611 timeout'

New Member

only send 4 digits to PSTN

Hi!

I just found the problem, i had a dial-peer voice with destinattion-pattern ´....´ , when i removed it, all right.

thanks everybody,

regards!!!

Hall of Fame Super Gold

only send 4 digits to PSTN

You're welcome, please remember to rate useful posts clicking on the stars below.

311
Views
0
Helpful
4
Replies