Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

Outbound calls taking some time to dial

Dear,

We are having a issue with outbound calls in Denmark.

When the customer wants to dial out to the PSTN it takes some time for the number to start dialling. I've already adjusted the T302 timer for this but that doesn't seem to be the issue.

The issue seems that the calls takes some time to form over to the PSTN.

I've done a debug trace of Q931 and from the moment he connects to the outside it takes a while for it to start ringing, i can start a detailed trace later today or tomorrow.

Are there any commands i could do to the E1 controller or the voiceport to speed up things, send a sending complete or something so the provider picks this up faster, or is this totally a provider issue?

Thanks,

Yannick

Everyone's tags (2)
4 REPLIES
Cisco Employee

Outbound calls taking some time to dial

Hi Yannick,

Please try to make the outbound call again and press "#" at the end of the call and check if the call still takes time to complete.

If the issue is still there then we need to collect the debugs on the gateway.

Thanks & Regards,
Mudit Mathur

Thanks & Regards, Mudit Mathur
Cisco Employee

Outbound calls taking some time to dial

Hi Yannick,

It depends on what you are seeing in the ISDN debugs:

If you see the following:

TX -> SETUP

RX <- Call Proceeding

..

Time delay

..

RX <- Alerting

Then it is an issue with the provider not routing the call immediately.

Also in the SETUP, you can check for the "Sending Complete", which means all digits have been mentioned in the called party and the call should be routed immediately.

Thanks

Sree

New Member

Outbound calls taking some time to dial

NYK01VG21#

Mar  6 10:52:40 CET: ISDN Se0/0/0:15 Q931: Applying typeplan for sw-type 0x12 is 0x0 0x0, Calling num 54847070

Mar  6 10:52:40 CET: ISDN Se0/0/0:15 Q931: Sending SETUP  callref = 0x0542 callID = 0x84C3 switch = primary-net5 interface = User

Mar  6 10:52:40 CET: ISDN Se0/0/0:15 Q931: TX -> SETUP pd = 8  callref = 0x0542

        Sending Complete

        Bearer Capability i = 0x8090A3

                Standard = CCITT

                Transfer Capability = Speech

                Transfer Mode = Circuit

                Transfer Rate = 64 kbit/s

        Channel ID i = 0xA9838C

                Exclusive, Channel 12

        Progress Ind i = 0x8183 - Origination address is non-ISDN

NYK01VG21#

        Calling Party Number i = 0x0081, '54847070'

                Plan:Unknown, Type:Unknown

        Called Party Number i = 0x80, '003227551617'

                Plan:Unknown, Type:Unknown

Mar  6 10:52:40 CET: ISDN Se0/0/0:15 Q931: RX <- CALL_PROC pd = 8  callref = 0x8542

        Channel ID i = 0xA9838C

                Exclusive, Channel 12

NYK01VG21#

Mar  6 10:52:50 CET: ISDN Se0/0/0:15 Q931: RX <- PROGRESS pd = 8  callref = 0x8542

        Progress Ind i = 0x8A81 - Call not end-to-end ISDN, may have in-band info

NYK01VG21#

Mar  6 10:52:54 CET: ISDN Se0/0/0:15 Q931: RX <- ALERTING pd = 8  callref = 0x8542

        Progress Ind i = 0x8A88 - In-band info or appropriate now available

Mar  6 10:52:55 CET: ISDN Se0/0/0:15 Q931: RX <- PROGRESS pd = 8  callref = 0x8542

        Progress Ind i = 0x8A88 - In-band info or appropriate now available

NYK01VG21#

Mar  6 10:52:55 CET: ISDN Se0/0/0:15 Q931: RX <- PROGRESS pd = 8  callref = 0x8542

        Progress Ind i = 0x8A88 - In-band info or appropriate now available

NYK01VG21#

Mar  6 10:53:00 CET: ISDN Se0/0/0:15 Q931: TX -> DISCONNECT pd = 8  callref = 0x0542

        Cause i = 0x8090 - Normal call clearing

Mar  6 10:53:00 CET: ISDN Se0/0/0:15 Q931: RX <- RELEASE pd = 8  callref = 0x8542

Mar  6 10:53:00 CET: ISDN Se0/0/0:15 Q931: TX -> RELEASE_COMP pd = 8  callref = 0x0542

NYK01VG21#

This is the output from the debug isdn q931, there is a 10 second delay between "Call Proc" and "Progress"

Anyone any ideas

Cisco Employee

Outbound calls taking some time to dial

Hi Yannick,

It's clear from your output that this is a telco issue.

Mar  6 10:52:40 CET: ISDN Se0/0/0:15 Q931: RX <- CALL_PROC pd = 8  callref = 0x8542

        Channel ID i = 0xA9838C

                Exclusive, Channel 12

NYK01VG21#

Mar  6 10:52:50 CET: ISDN Se0/0/0:15 Q931: RX <- PROGRESS pd = 8  callref = 0x8542

        Progress Ind i = 0x8A81 - Call not end-to-end ISDN, may have in-band info

NYK01VG21#

The provider will have to rectify the 10 second delay it takes for them to reach the number called.

The ringback will only begin once the progress information has been received and it will come in band from the telco.

Thanks

Sree

171
Views
0
Helpful
4
Replies
CreatePlease login to create content