Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Community Member

Outbound pots dial-peers

Trying to map outbound local and LD calls to their respective T1's based on dial-peers.

How do I make a specifice match for local calls to use certain ports regardless of dial-peer pref?

As it is now it matches all peers when I dial a local 10 digit number beginning 651XXX-XXXX but I want it to match pots dp 3 instead of going out pots dp 6. Any suggestions?

!

dial-peer voice 3 pots

description MNLX_Local_RG Primary

preference 3

destination-pattern [651,763,612,952].

progress_ind setup enable 3

progress_ind progress enable 8

progress_ind connect enable 8

incoming called-number .

direct-inward-dial

port 7/0:16:D

!

dial-peer voice 4 pots

description MNLX_Local_RG Secondary

preference 4

destination-pattern [651,763,612,952].

progress_ind setup enable 3

progress_ind progress enable 8

progress_ind connect enable 8

incoming called-number .

direct-inward-dial

port 7/0:15:D

!

dial-peer voice 5 pots

description MN Gen LD

preference 2

destination-pattern [2-9].

progress_ind setup enable 3

progress_ind progress enable 8

progress_ind connect enable 8

incoming called-number .

direct-inward-dial

port 7/0:13:D

!

dial-peer voice 6 pots

description MN Gen LD

preference 1

destination-pattern [2-9].

progress_ind setup enable 3

progress_ind progress enable 8

progress_ind connect enable 8

incoming called-number .

direct-inward-dial

port 7/0:14:D

!

Dec 11 21:48:14.814: //-1/003F7FC53300/DPM/dpMatchPeersMoreArg:

Result=SUCCESS(0)

List of Matched Outgoing Dial-peer(s):

1: Dial-peer Tag=6

2: Dial-peer Tag=5

3: Dial-peer Tag=3

4: Dial-peer Tag=4

Dec 11 21:48:14.814: ISDN Se7/0:14:23 Q931: pak_private_number: Invalid type/plan 0x0 0x0 may be overriden; sw-type 2

Dec 11 21:48:14.814: ISDN Se7/0:14:23 Q931: Applying typeplan for sw-type 0x2 is 0x2 0x1, Calling num 8512

Dec 11 21:48:14.818: ISDN Se7/0:14:23 Q931: Applying typeplan for sw-type 0x2 is 0x2 0x1, Called num 6513238925

Dec 11 21:48:14.818: ISDN Se7/0:14:23 Q931: TX -> SETUP pd = 8 callref = 0x00BB

Bearer Capability i = 0x8090A2

Standard = CCITT

Transfer Capability = Speech

Transfer Mode = Circuit

Transfer Rate = 64 kbit/s

Channel ID i = 0xA98397

Exclusive, Channel 23

Net Specific Fac i = 0x00E1

Calling Party Number i = 0x2181, '8512'

Plan:ISDN, Type:National

Called Party Number i = 0xA1, '6513238925'

Plan:ISDN, Type:National

Dec 11 21:48:14.878: ISDN Se7/0:14:23 Q931: RX <- CALL_PROC pd = 8 callref = 0x80BB

Channel ID i = 0xE9808397

Exclusive, Interface 0, Channel 23

Dec 11 21:48:16.698: ISDN Se7/0:14:23 Q931: RX <- ALERTING pd = 8 callref = 0x80BB

Dec 11 21:48:17.346: ISDN Se7/0:14:23 Q931: TX -> DISCONNECT pd = 8 callref = 0x00BB

Cause i = 0x8090 - Normal call clearing

Dec 11 21:48:17.406: ISDN Se7/0:14:23 Q931: RX <- RELEASE pd = 8 callref = 0x80BB

Dec 11 21:48:17.410: ISDN Se7/0:14:23 Q931: TX -> RELEASE_COMP pd = 8 callref = 0x00BB

3 pots up up [651,763,612,952]. 3 up 7/0:16:D

4 pots up up [651,763,612,952]. 4 up 7/0:15:D

5 pots up up [2-9]. 2 up 7/0:13:D

6 pots up up [2-9]. 1 up 7/0:14:D

1 REPLY
Silver

Re: Outbound pots dial-peers

Dial-peer preference is the best way to match dial-peer or try with exact destination-pattern match for ex destination-patern1001, destination-patern1002.

143
Views
0
Helpful
1
Replies
CreatePlease to create content