I am struggling to get this right. I need to let my call manager send out external phone mask. I see the right digits being sent using 'deb voip ccapi inout'. I have removed 'translation-profile outgoing PSTN_Outbound' from the outbound dial-peers, but then the call simply results in fast busy. I can change the 8819 to any DID on the circuit and it will go out.
How do I revise the configuration to pass the external phone mask from CUCM?
SJB_113A_C2901_132.45#sh run | sec voice voice-card 0 dspfarm dsp services dspfarm voice call send-alert voice call carrier capacity active voice rtp send-recv voice service voip allow-connections sip to sip no supplementary-service sip handle-replaces fax protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback none h323 h225 display-ie ccm-compatible modem passthrough nse codec g711ulaw sip bind control source-interface GigabitEthernet0/1.5 bind media source-interface GigabitEthernet0/1.5 header-passing early-offer forced midcall-signaling passthru voice class codec 10 codec preference 1 g711ulaw codec preference 5 g729r8 voice translation-rule 10 rule 1 /^911$/ /911/ rule 2 /^9\(.*\)/ /\1/ rule 3 /^9011$/ /011/ voice translation-rule 20 rule 1 /.*/ /4082879919/ voice translation-profile PSTN_Outbound translate calling 20 translate called 10 isdn incoming-voice voice voice-port 0/0/0 station-id number 4084596401 voice-port 0/0/1 voice-port 0/0/2 voice-port 0/0/3 voice-port 0/1/0:23 input gain -3 output attenuation 3 echo-cancel coverage 32 no comfort-noise timeouts interdigit 2 description connection to PSTN bearer-cap Speech voice-port 0/2/0 voice-port 0/2/1 voice-port 0/2/2 voice-port 0/2/3 ! ! ! dial-peer voice 1 pots description POTS Dial Peer - Inbound PRI from PSTN translation-profile outgoing PSTN_Outbound incoming called-number . direct-inward-dial dial-peer voice 9211 pots description POTS Dial Peer for Local Services Dialing translation-profile outgoing PSTN_Outbound destination-pattern 9[2-8]11 port 0/1/0:23 forward-digits all dial-peer voice 911 pots description POTS Dial Peer for Local Emergency 911 Calling translation-profile outgoing PSTN_Outbound destination-pattern 911 port 0/1/0:23 forward-digits all dial-peer voice 9911 pots description POTS Dial Peer for Local Emergency 911 Calling translation-profile outgoing PSTN_Outbound destination-pattern 9911 port 0/1/0:23 forward-digits all dial-peer voice 20 pots description POTS Dial Peer for Local Calling translation-profile outgoing PSTN_Outbound destination-pattern 9[2-9]...... port 0/1/0:23 forward-digits all dial-peer voice 30 pots description POTS Dial Peer for Long Distance Calling translation-profile outgoing PSTN_Outbound destination-pattern 91...[2-9]...... port 0/1/0:23 forward-digits all dial-peer voice 40 pots description POTS Dial Peer for Long Distance Calling w/o 1 translation-profile outgoing PSTN_Outbound destination-pattern 9[2-9]..[2-9]...... port 0/1/0:23 forward-digits all dial-peer voice 50 pots description POTS Dial Peer for International Calling translation-profile outgoing PSTN_Outbound destination-pattern 9011T no digit-strip port 0/1/0:23 forward-digits all dial-peer voice 2000 voip description INBOUND Dial-Peer for 4082879919 preference 2 destination-pattern [1-8]...$ session protocol sipv2 session target ipv4:192.168.139.30 incoming called-number . voice-class codec 10 dtmf-relay rtp-nte sip-kpml ip qos dscp cs3 signaling no vad dial-peer voice 3100 pots description OUTBOUND to FAX Port Voice 0/0/0 650-459-6401 destination-pattern ^6401$ no digit-strip port 0/0/0 dial-peer voice 3000 voip description INBOUND fax number 650-459-6401 session protocol sipv2 incoming called-number ^6401$ dtmf-relay rtp-nte codec g711ulaw fax protocol pass-through g711ulaw no vad
To pass external phone number mask simply check it on the route pattern or route list and don't do any additional transformation on the gateway. A lot of carriers will block calls or replace the ANI with BTN if you attempt to present a DID that does not ride on the circuit. To resolve it you can check with the carrier to see if they will remove ANI screening, some won't so you are stuck with sending BTN for single number reach calls for example or look for different carrier. Let us know if this answers your question or if you have something more specific in mind.
I am aware of that. The carrier will allow the numbers.
For example, I changed - rule 1 /.*/ /4082879919/ (main line) to - rule 1 /.*/ /4084596499/ (DID on circuit) and the outbound caller-id would show as 6499.
If I remove 'translate calling 20' from 'voice translation-profile PSTN_Outbound', the calls stop working.
If I remove 'voice translation-profile PSTN_Outbound' from the dial-peers, calls stop working.
To be honest, I'm not sure what voice translation rule 10 does? I'm assuming it deals with 911 calls so I'm hesitant to mess with it. This was all done by a previous engineer and it's stuff I'm not up to speed on yet.
Are you getting this error “Installer User Interface Mode Not Supported. The installer cannot run in this UI mode. To specify the interface mode, use the -i command-line option, followed by the UI mode identifier. The value UI mode identifiers...
The below trick might come handy when you have to add a new node to a cluster but you don't have or is unsure of the security password for the publisher. This procedure has been around for ages.
1) Login into the CLI of the Publisher.