Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

Outgoing and Incoming Call on UC540

Hi All,

we have almost done with the config of the UC540 IP System. We are able to make internal call. We need now to handle the outgoing and incoming calls.

how  to :

  • Configure the ‘voice translation-rule’ ,  the “voice translation profile”  the  “dial-peer   pots”  and “translation profile” for national call
  • Configure the ‘voice translation-rule’ ,  the “voice translation profile”  the  “dial-peer   pots” and the “translation profile” for international call

 

The system is UC540W with 4 FXO ports (analog line).

We have 2 land lines phone (0302500325 ; 0302500326) & 1 International line (0302500324)

 

Thanks in advance !²

  • IP Telephony
7 REPLIES

Hi, I suggest you follow the

Hi,

 

I suggest you follow the below pdf.

 

http://www.cisco.com/c/en/us/td/docs/ios/voice/dialpeer/configuration/guide/12_4t/vd_12_4t_book/vd_dp_cfg_examp.pdf

 

Rate for Gods sake!!!!.

Hi,I read the doc and  build

Hi,

I read the doc and  build my config.

We are able to receive calls coming IN on each of the phone number. But we make call.

The phone say "Line Busy" all the time.  Can you help me to understand the issue ?

Bellow the config :

!
voice translation-rule 1
 rule 1 /^86/ //
 rule 2 /^87/ //
 rule 3 /^88/ //
!
voice translation-rule 2
 rule 1 /0302500324/ /100/
 rule 2 /0302500325/ /104/
 rule 3 /0302500326/ /105/
!
voice translation-profile GH-IN
 translate calling 2
!
voice translation-profile GH-OUT
 translate called 1
!

!

!
voice-port 0/1/0
 trunk-group ALL_FXO 64
 translation-profile incoming GH-IN
 translation-profile outgoing GH-OUT
 supervisory disconnect dualtone mid-call
 cptone GH
 timeouts call-disconnect 2
 timeouts wait-release 2
 connection plar opx 100
 description Line VODAFONE 0302 544 324
 caller-id enable
!
voice-port 0/1/1
 trunk-group ALL_FXO 64
 translation-profile incoming GH-IN
 translation-profile outgoing GH-OUT
 supervisory disconnect dualtone mid-call
 cptone GH
 timeouts call-disconnect 2
 timeouts wait-release 2
 connection plar opx 104
 description Line VODAFONE 0302 544 325
 caller-id enable
!
voice-port 0/1/2
 trunk-group ALL_FXO 64
 translation-profile incoming GH-IN
 translation-profile outgoing GH-OUT
 supervisory disconnect dualtone mid-call
 cptone GH
 timeouts call-disconnect 2
 timeouts wait-release 2
 connection plar opx 105
 description Line VODAFONE 0302 544 326
 caller-id enable
!

!

!
dial-peer voice 54 pots
 description **International Call**
 destination-pattern 88.T
 port 0/1/0
 forward-digits all
 no sip-register
!
dial-peer voice 55 pots
 description ** National Calls **
 destination-pattern 87..........
 port 0/1/1
 forward-digits 10
 no sip-register
!
dial-peer voice 56 pots
 description ** National Calls **
 destination-pattern 86..........
 port 0/1/2
 forward-digits 10
 no sip-register
!

 

 

A voice says the line is busy

A voice says the line is busy or are you getting a busy tone?

Busy tone, with "Busy" word

Busy tone, with "Busy" word on the screen

I'm assuming that the call

I'm assuming that the call was made from Internal to PSTN.

 

Please post the number your dialing and the debug below.

 

Debug:

debug voice ccapi inout

debug voip dialpeer inout 

 

Please make sure that you use the debug commands one a time.

Fixed now  :) But when we

Fixed now  :)

 

But when we receive a call from isdn, we have   UNKNOWN NUMBER

any ideas ?

If your receving unknown

If your receving unknown numbers, input the below config and  use the below debug on the router.

 

voice-port x/x/x/

caller-id enable

 

Debug:

debug vpm signal(post output.

70
Views
7
Helpful
7
Replies