03-12-2009 02:47 PM - edited 03-15-2019 04:49 PM
I recently upgraded to UCM 7.0 from CM 4.1.3. After the upgrade I have been noticing a various phone numbers are flagged as international when they are processed by the h323 gateway. It seems to be relative to a particular area code. All of these calls that fail are national.
1402035: Mar 12 15:39:08.008 CST: ISDN Se1/0:23 Q931: isdn_parser_map_lkup: overriding plan/type for XXXXXXXXXX, isdn/national to isdn/international
1402036: Mar 12 15:39:08.012 CST: ISDN Se1/0:23 Q931: isdn_parser_map_lkup: overriding plan/type for XXXXXXXXXX, isdn/national to isdn/international
1402037: Mar 12 15:39:08.020 CST: ISDN Se1/0:23 Q931: TX -> SETUP pd = 8 callref = 0x744C
Bearer Capability i = 0x8090A2
Standard = CCITT
Transer Capability = Speech
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xE9818398
Exclusive, Interface 1, Channel 24
Calling Party Number i = 0x2181, 'XXXXXXXXXX'
Plan:ISDN, Type:National
Called Party Number i = 0x91, 'XXXXXXXXXX'
Plan:ISDN, Type:International
1402038: Mar 12 15:39:08.068 CST: ISDN Se1/0:23 Q931: RX <- RELEASE_COMP pd = 8 callref = 0xF44C
Solved! Go to Solution.
03-12-2009 11:09 PM
1402035: Mar 12 15:39:08.008 CST: ISDN Se1/0:23 Q931: isdn_parser_map_lkup: overriding plan/type for XXXXXXXXXX, isdn/national to isdn/international
1402036: Mar 12 15:39:08.012 CST: ISDN Se1/0:23 Q931: isdn_parser_map_lkup: overriding plan/type for XXXXXXXXXX, isdn/national to isdn/international
do u have a rule defined in the serial interface for this T1 PRI?
like isdn map ?
http://www.cisco.com/en/US/docs/ios/12_3t/dial/command/reference/dia_i2gt.html#wp1212108
03-12-2009 11:09 PM
1402035: Mar 12 15:39:08.008 CST: ISDN Se1/0:23 Q931: isdn_parser_map_lkup: overriding plan/type for XXXXXXXXXX, isdn/national to isdn/international
1402036: Mar 12 15:39:08.012 CST: ISDN Se1/0:23 Q931: isdn_parser_map_lkup: overriding plan/type for XXXXXXXXXX, isdn/national to isdn/international
do u have a rule defined in the serial interface for this T1 PRI?
like isdn map ?
http://www.cisco.com/en/US/docs/ios/12_3t/dial/command/reference/dia_i2gt.html#wp1212108
03-13-2009 07:35 AM
Thanks for the information. It does work to force the isdn type to national. Any idea why this particular area code gets flagged as international? Here's my serial config:
interface Serial1/0:23
no ip address
no logging event link-status
isdn switch-type primary-4ess
isdn incoming-voice voice
isdn map address 011* plan isdn type international
isdn map address 770* plan isdn type national
no isdn outgoing ie redirecting-number
no isdn incoming alerting add-PI
isdn nsf-service megacom
no cdp enable
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: