Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

Peer Firmware Sharing CM4.2

have 200 remote phones that I will be pushing new image to. has anyone used this to assist in downloading image, instead of all the phones going over a WAN. I enabled the "peer firmware sharing" field on the phone product config, not to sure what to do now. Thanks

1 ACCEPTED SOLUTION

Accepted Solutions
Hall of Fame Super Red

Re: Peer Firmware Sharing CM4.2

Hi Pete,

Have a look at this post where someone actually got this working. It only works with specific models of IP Phones. The Option 150 does not need to change;

http://forum.cisco.com/eforum/servlet/NetProf?page=netprof&forum=Unified%20Communications%20and%20Video&topic=IP%20Telephony&topicID=.ee6c829&fromOutline=true&CommCmd=MB%3Fcmd%3Ddisplay_location%26location%3D.2cc055e5/0

Hope this helps!

Rob

8 REPLIES

Re: Peer Firmware Sharing CM4.2

Interesting question, havent tried this but worth a try...

The description is very clear:

PPID. Enables or disables Peer to Peer image distribution in order to allow a single phone in a subnet to retrieve an image firmware file then distribute it to its peers - thus reducing TFTP bandwidth and providing for a faster firmware upgrade time.

This is a required field.

Default: Disabled

So you would configure dhcp scopes of remaining phones to point to this ip phone as tftp server. I d suggest that you do not plug in all phones at the same time as the phone may not be able to handle hundreds of requests at the same time...

New Member

Re: Peer Firmware Sharing CM4.2

Didnt think it could be that easy (point phones to it), but will try. there is also a 4.x tool called ccmppid, which turns multiple phones into tftp servers.

thanks for your help

Re: Peer Firmware Sharing CM4.2

Let me know how this works for you..i am very much interested to know the performance of the tftp server on the phone.

New Member

Re: Peer Firmware Sharing CM4.2

Hello. aparently, its not as simple as pointing the other phones to the upgraded phones. Phone is enabled for firmware sharing.Changed option 150 to phone IP address, rebooted phones, doesnt pick up new image.

Re: Peer Firmware Sharing CM4.2

After reading some information on this my take is that you would enable peer firmware sharing on all phones at the remote sites, and a master is elected.

Read Below:

Peer Firmware Sharing

This feature allows peer firmware sharing on a remote location, in order to save bandwidth during the upgrade of the IP phones.

The configuration is very simple. Update the feature on the IP phones on

the remote location and one of the devices is selected as master and it shares the file with the other IP phones.

Here also is a FAQ

http://www.cisco.com/en/US/products/hw/phones/ps379/products_qanda_item09186a00800a6763.shtml#q46

Matt

New Member

Re: Peer Firmware Sharing CM4.2

Interesting. thanks for the info. Then what would I use for TFTP Server under Option 150 of the dhcp voice network?

Hall of Fame Super Red

Re: Peer Firmware Sharing CM4.2

Hi Pete,

Have a look at this post where someone actually got this working. It only works with specific models of IP Phones. The Option 150 does not need to change;

http://forum.cisco.com/eforum/servlet/NetProf?page=netprof&forum=Unified%20Communications%20and%20Video&topic=IP%20Telephony&topicID=.ee6c829&fromOutline=true&CommCmd=MB%3Fcmd%3Ddisplay_location%26location%3D.2cc055e5/0

Hope this helps!

Rob

New Member

Re: Peer Firmware Sharing CM4.2

Well at least I have some answers now. Cant figure out how to select multiple phones to upgrade. There is no BAT for product specific ocnfigs. So far, have selected individual phones and enabled firmware sharing, then reset them and others at the same time.

thanks for all your help

214
Views
4
Helpful
8
Replies