Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

Phone load & templates for SRST Mode

Any body can help what is wrong with this config. and how I can get auto load from CUCM, I am unable to get phone loaded, please see attached phone regesteration log.

telephony-service

srst mode auto-provision all

srst ephone template 5

srst ephone description srst fallback auto-provision phone  : Feb 10 2012 20:56:40

srst dn template 3

srst dn line-mode dual

max-ephones 30

max-dn 60

ip source-address 10.221.82.15 port 2000

system message Tatweer Petroleum

max-conferences 8 gain -6

transfer-system full-consult

create cnf-files version-stamp 7960 Feb 12 2012 07:06:06

!

!

ephone-dn-template  3

!

!

ephone-template  5

softkeys idle  Newcall Cfwdall Pickup

softkeys seized  Endcall Cfwdall Pickup

softkeys alerting  Endcall

softkeys connected  Endcall Hold Park Trnsfer telephony-service

Thanks

Ali

1 ACCEPTED SOLUTION

Accepted Solutions
Hall of Fame Super Silver

Phone load & templates for SRST Mode

Yes, you need to upgrade IOS to at least 15.1.1T as that is the first version that supported these phones.

http://www.cisco.com/en/US/docs/voice_ip_comm/cucme/requirements/guide/33matrix.htm

As to the firmware upgrade after you install the firware on CUCM server, if you do not want to apply it to all phones simply make sure the device defaults page references the old firmware and then manually assign the new one as the load version on a single phone you want to use.

HTH, please rate all useful posts!

Chris

7 REPLIES
Hall of Fame Super Silver

Phone load & templates for SRST Mode

What is the phone type and what are you seeing on the phone?

Chris

New Member

Phone load & templates for SRST Mode

Hi Chris

The phone model is 6921, and the message on the phone is "Phone not registered".

I tested with 7945 model and it works, but with the model above dosen't work.

Thanks

Ali

Hall of Fame Super Silver

Phone load & templates for SRST Mode

What version of IOS are you using? This may be bug CSCti24483.

Notice the following error:

StationButtonTemplateReqMessage for unsupported phone-type 495

Here is similar threads:

https://supportforums.cisco.com/message/3537656#3537656

HTH,

Chris

New Member

Phone load & templates for SRST Mode

IOS ver 15.0

Any idea how do I upload the firmware on the SRST router, and where to download?

Thanks

Ali

Hall of Fame Super Silver

Phone load & templates for SRST Mode

First I would update the IOS to either 15.1T or 15.1M train.

The I would install latest firmware file for 6921 phone on CUCM.

To download all of the above you need to have valid Cisco contract, for IOS you browse to Support --> Downloads --> IOS and locate your router type

For 6921 firmware you can get it from here:

http://www.cisco.com/cisco/software/release.html?mdfid=282622815&flowid=5289&softwareid=282074289&release=9.2%282%29&relind=AVAILABLE&rellifecycle=&reltype=latest

HTH, please rate all useful posts!

Chris

New Member

Phone load & templates for SRST Mode

Hi Chris,

Do I need to update the IOS?

Can I upload the firmware for one disk phone, could you please give me the procedure.

Thanks

Hall of Fame Super Silver

Phone load & templates for SRST Mode

Yes, you need to upgrade IOS to at least 15.1.1T as that is the first version that supported these phones.

http://www.cisco.com/en/US/docs/voice_ip_comm/cucme/requirements/guide/33matrix.htm

As to the firmware upgrade after you install the firware on CUCM server, if you do not want to apply it to all phones simply make sure the device defaults page references the old firmware and then manually assign the new one as the load version on a single phone you want to use.

HTH, please rate all useful posts!

Chris

674
Views
5
Helpful
7
Replies