Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

PRA layer 3 problem on outgoing calls

Hi,

i've a 2811 voice-gateway in a location in poland.All inbound calls are fine - no problems. But i experiencing strange problems on outgoing calls: Some calls are OK - but almost all outgoing calls fail. In the debug, i get the "CALL_PROC" and the "ALERTING" (the called phone rings). But after that, my gateway sends a "DISCONNECT".

Jul 15 06:17:47.266: ISDN Se0/2/0:15 Q931: Applying typeplan for sw-type 0x12 is 0x1 0x1, Calling num 48717XXXXX
Jul 15 06:17:47.270: ISDN Se0/2/0:15 Q931: Sending SETUP  callref = 0x00A0 callID = 0x8021 switch = primary-net5 interface = User
Jul 15 06:17:47.270: ISDN Se0/2/0:15 Q931: TX -> SETUP pd = 8  callref = 0x00A0
        Sending Complete
        Bearer Capability i = 0x8090A3
                Standard = CCITT
                Transfer Capability = Speech
                Transfer Mode = Circuit
                Transfer Rate = 64 kbit/s
        Channel ID i = 0xA18381
                Preferred, Channel 1
        Progress Ind i = 0x8183 - Origination address is non-ISDN
WRO-STADIUM-VG1#
        Calling Party Number i = 0x1181, '48717XXXXX'
                Plan:ISDN, Type:International
        Called Party Number i = 0x91, '49XXXXXXXXX'
                Plan:ISDN, Type:International
Jul 15 06:17:47.358: ISDN Se0/2/0:15 Q931: RX <- CALL_PROC pd = 8  callref = 0x80A0
        Channel ID i = 0xA98381
                Exclusive, Channel 1
WRO-STADIUM-VG1#
Jul 15 06:17:53.382: ISDN Se0/2/0:15 Q931: RX <- ALERTING pd = 8  callref = 0x80A0
WRO-STADIUM-VG1#
Jul 15 06:17:57.786: ISDN Se0/2/0:15 Q931: TX -> DISCONNECT pd = 8  callref = 0x00A0
        Cause i = 0x80BF - Service/option not available, unspecified
Jul 15 06:17:57.826: ISDN Se0/2/0:15 Q931: RX <- RELEASE pd = 8  callref = 0x80A0
        Cause i = 0x80BF - Service/option not available, unspecified
Jul 15 06:17:57.830: ISDN Se0/2/0:15 Q931: TX -> RELEASE_COMP pd = 8  callref = 0x00A0

  • IP Telephony
4 REPLIES
Hall of Fame Super Gold

Re: PRA layer 3 problem on outgoing calls

Which exact IOS ?

New Member

Re: PRA layer 3 problem on outgoing calls

12.4.24T

New Member

Re: PRA layer 3 problem on outgoing calls

Update: Both, inbound and outbound calls have these problems...

Hall of Fame Super Gold

Re: PRA layer 3 problem on outgoing calls

Are you using CM? I remember some wrong setting there can cause that. Unfortunately, I don't remember which ones.

230
Views
0
Helpful
4
Replies
This widget could not be displayed.