Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

PRI line to CallManagerExpress - enabling caller ID?

Hi,

How to enable the caller id? When a call arrives from outside via PRI lines to call manager express the users do not see caller ids. How to enable it ?

thx

4 REPLIES
Hall of Fame Super Gold

Re: PRI line to CallManagerExpress - enabling caller ID?

Please send output of "debug isdn q931" with "term mon" for an incoming call.

New Member

Re: PRI line to CallManagerExpress - enabling caller ID?

Feb 13 15:27:19.011: ISDN Se0/0/0:15 Q931: RX <- SETUP pd = 8 callref = 0x0B1C

Sending Complete

Bearer Capability i = 0x8090A3

Standard = CCITT

Transfer Capability = Speech

Transfer Mode = Circuit

Transfer Rate = 64 kbit/s

Channel ID i = 0xA98383

Exclusive, Channel 3

Progress Ind i = 0x8583 - Origination address is non-ISDN

Called Party Number i = 0x81, '798'

Plan:ISDN, Type:Unknown

Feb 13 15:27:19.027: ISDN Se0/0/0:15 Q931: TX -> CALL_PROC pd = 8 callref = 0x8B1C

Channel ID i = 0xA98383

Exclusive, Channel 3

Feb 13 15:27:19.579: ISDN Se0/0/0:15 Q931: TX -> ALERTING pd = 8 callref = 0x8B1C

Feb 13 15:27:19.635: ISDN Se0/0/0:15 Q931: TX -> CONNECT pd = 8 callref = 0x8B1C

Feb 13 15:27:19.667: ISDN Se0/0/0:15 Q931: RX <- CONNECT_ACK pd = 8 callref = 0x0B1C

Feb 13 15:27:19.667: %ISDN-6-CONNECT: Interface Serial0/0/0:2 is now connected to N/A N/A

Feb 13 15:27:25.667: %ISDN-6-CONNECT: Interface Serial0/0/0:2 is now connected to N/A N/A

Feb 13 15:27:27.779: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/0:2, changed state to up

Feb 13 15:27:28.123: ISDN Se0/0/0:15 Q931: RX <- DISCONNECT pd = 8 callref = 0x0B1C

Cause i = 0x8090 - Normal call clearing

Progress Ind i = 0x8288 - In-band info or appropriate now available

Feb 13 15:27:28.123: %ISDN-6-DISCONNECT: Interface Serial0/0/0:2 disconnected from unknown , call lasted 8 seconds

Feb 13 15:27:28.123: ISDN Se0/0/0:15 Q931: call_disc: PI received in disconnect; Postpone sending RELEASE for callid 0x4

Feb 13 15:27:28.135: ISDN Se0/0/0:15 Q931: TX -> RELEASE pd = 8 callref = 0x8B1C

Feb 13 15:27:28.147: ISDN Se0/0/0:15 Q931: RX <- RELEASE_COMP pd = 8 callref = 0x0B1C

Hall of Fame Super Gold

Re: PRI line to CallManagerExpress - enabling caller ID?

Like Dave also suggested, there is no caller number in the setup message, so you have to raise the issue with your telco.

Bronze

Re: PRI line to CallManagerExpress - enabling caller ID?

Okan,

Check with your SP that Caller ID is enabled.

Regards,

Dave

145
Views
0
Helpful
4
Replies
CreatePlease login to create content