Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Community Member

Problem on forward internal calls to voice mail

Hi voice team,

     I configured on CME extension 4815 the option:

     call-forward busy 6800 -> VOICE MAIL EXTENSION

     call-forward noan 6800 timeout 10

     I have a problem in my CME because when i calling from my extension 9072 (CUCM) to CME extension 4815 after ringing 4 times, 4815 dont forward to voice mail 6800, the extension 4815 still ringing (the connection gets stuck), but when i call from external number to 4815, the 4815 forward to 6800 normally.

From my extension 4815 i can digit to voice mal normally too.

Thanks,

PS: attached are the sh run from my CME router.


17 REPLIES
Cisco Employee

Problem on forward internal calls to voice mail

Hello Thiago,

A quick quesiton, does all calls from CUCM to any Extn to CME 4815 does not work? How CME and CUCM is connected (Connection) ?


Br,
Nadeem 

Please rate all useful post.

Br, Nadeem Please rate all useful post.
Community Member

Problem on forward internal calls to voice mail

Hello Nadeem, all calls to CME works fine. The CME is connected through SIP Ttrunk to CUCM.

Hall of Fame Super Red

Problem on forward internal calls to voice mail

Hi Thiago,

In addition to the good ideas from my friend Nadeem (+5 )

I might check out this similar thread;

https://supportforums.cisco.com/message/1093094#1093094

And;

http://www.cisco.com/en/US/docs/voice_ip_comm/cucme/srnd/design/guide/clproc.html#wp1068478

Cheers!

Rob

"Seek it out and ye shall find  " 

- OneRepublic

Cisco Employee

Re: Problem on forward internal calls to voice mail

Do not see call-forward pattern  in your below config.

telephony-service

max-ephones 42

max-dn 144

ip source-address 10.19.1.254 port 2000

service phone videoCapability 1

service dss

timeouts interdigit 20

timeouts busy 20

timeouts ringing 30

system message DUAS RODAS-CAM

time-zone 17

time-format 24

date-format dd-mm-yy

voicemail 6800

max-conferences 8 gain -6

moh flash:/musica.ulaw

transfer-system full-consult

secondary-dialtone 0

directory entry 1 004199418400 name JeanIT7

create cnf-files version-stamp Jan 01 2002 00:00:00

!

Just add call-forward pattern .T and make the test call,

@Rob thanks for the Hi5, I think you have already answered it.(+5) for you.

Br,
Nadeem 

Please rate all useful post.

Br, Nadeem Please rate all useful post.
Community Member

Problem on forward internal calls to voice mail

I did it, but the problem persist, i need to add the transfer-pattern .T too ??

Cisco Employee

Re: Problem on forward internal calls to voice mail

Yes add it and do no create cnf and create cnf.


Br,
Nadeem 

Please rate all useful post.

Br, Nadeem Please rate all useful post.
Community Member

Problem on forward internal calls to voice mail

I add and do the cnf files, but the problem persist,

Thanks,

Cisco Employee

Problem on forward internal calls to voice mail

Can you try disabling this under voice-service voip, give it shot if didn't work we need to look into the debug why CME is not  even try do a transfer to the voicemail, the phone keep ringing and the originating side keep hearing the ringback for time.

voice service voip

 no supplementary-service h450.2


Br,
Nadeem 

Please rate all useful post.

Br, Nadeem Please rate all useful post.
Community Member

Re: Problem on forward internal calls to voice mail

Hi Nadeem, i made this but the problem persist.

Attached are the debug log:

Debug voice ccapi inout

Debug ccsip messages

Not work log

Calling extension: 9072

Called extension: 4815

Work log

Calling number: 4733729072

Called number: 4815

Voice mail number: 6800

Thanks,

Re: Problem on forward internal calls to voice mail

Hi Thiago,

Was checking your CME router configuration , as per configuration the inbound dial-peer from CUCM is 10 .You said your CME router is configured as sip trunk but dial-peer is not configured as SIP peer.

dial-peer voice 10 voip

incoming called-number .

dtmf-relay h245-alphanumeric

no vad

What i think its matching the default dial-peer when you call from CUCM to CME , which is creating this problem. You can try this and let us know if that resolves your issue.

dial-peer voice 10 voip

incoming called-number .

session protocol sipv2

no vad

Rate all the helpful post.

Thanks

Manish

Community Member

Re: Problem on forward internal calls to voice mail

I made this config, but not work. Internal calls keeping ringing and dont transfer to voice mail.

Re: Problem on forward internal calls to voice mail

.Internal calls keeping ringing and dont transfer to voice mail.- what do you mean by that , from cme ext to cme ext its also the same issue?

Sent from Cisco Technical Support iPhone App

Community Member

Re: Problem on forward internal calls to voice mail

Yes, works normally.

CME tranfer to another CME extension and CME transfer to another CUCM extension.

The debugs are attached.

Not work

Calling extension: 9072

Called extension: 4815

Work scenario

Calling number: 4733729072

Called number: 4815

Voice mail number: 6800

Community Member

Re: Problem on forward internal calls to voice mail

Sorry Mauro Pasetto i delete your post unintentionally

Problem on forward internal calls to voice mail

Hi Thiago.

Log captured seems incomplete. Please upload a full output of the debug to analyze better what is happening.

Thanks

Regards

Carlo

Please rate all helpful posts

"The more you help the more you learn"

Please rate all helpful posts "The more you help the more you learn"
Community Member

Re: Problem on forward internal calls to voice mail

Its the full output log.

Community Member

Re: Problem on forward internal calls to voice mail

Hi voice team,

The engineer Pablo Gonzales discovered that when the call hit Exchange, Exchange was requesting to moved temporarily to port 5065 on sip connection and however, GW(CME) was still sending the INVITE to exchange on port 5060.

So we issue a "no notify redirect ip2ip" on dial-peer 7 and this fix the issue. Now the calls are using port 5065 to Exchange and hitting Voicemail correctly.

Thanks,


305
Views
19
Helpful
17
Replies
CreatePlease to create content