Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

Problem sending fax multiple pages through a VG224

Problem sending fax multiple pages through a VG224

I have problems sending FAX over 8 pages, the parametric I configured are:

System image file is "slot0:vg224-i6s-mz.124-9.T7.bin"

voice service voip
fax protocol t38 ls-redundancy 0 hs-redundancy 0 fallback pass-through g711alaw
h323
  h225 timeout setup 30

dial-peer voice 4 voip
preference 1
destination-pattern 0[689]........$
progress_ind setup enable 3
voice-class codec 1
voice-class h323 1
session target ipv4:XX.XXX.XXX.XXX
dtmf-relay h245-alphanumeric
ip qos dscp cs3 signaling
no vad


In the CCM(6.1.3.1000-16) configuration set to H.323 Gateway.


What is the problem?.

Thank you very much to all

Greetings

1 ACCEPTED SOLUTION

Accepted Solutions
Hall of Fame Super Gold

Re: Problem sending fax multiple pages through a VG224

is adujusting the h225 timeout tcp establish. To 10 or 12 should be suffiecent.

Cannot be a TCP timeout problem, session gets established OK, and only drops after.

12 REPLIES
Hall of Fame Super Gold

Re: Problem sending fax multiple pages through a VG224

Please send "show controllers E1" from PSTN GW.

Re: Problem sending fax multiple pages through a VG224

Hi and thanks for the prompt attention on your part.

Here are the sh controller GW contact with the PSTN:

E1 0/0/0 is up.
  Applique type is Channelized E1 - unbalanced
  No alarms detected.
  alarm-trigger is not set
  Version info Firmware: 20071129, FPGA: 20, spm_count = 0
  Framing is NO-CRC4, Line Code is HDB3, Clock Source is Line.
  CRC Threshold is 320. Reported from firmware  is 320.
  Data in current interval (699 seconds elapsed):
     0 Line Code Violations, 0 Path Code Violations
     0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
  Total Data (last 24 hours)
     0 Line Code Violations, 0 Path Code Violations,
     0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,
     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs

E1 0/1/1 is up.
  Applique type is Channelized E1 - unbalanced
  Cablelength is Unknown
  Description: PRIMARIO FIJOS XXXXXXX : DDF Posc. 5
  No alarms detected.
  alarm-trigger is not set
  Version info Firmware: 20071011, FPGA: 13, spm_count = 0
  Framing is CRC4, Line Code is HDB3, Clock Source is Line.
  CRC Threshold is 320. Reported from firmware  is 320.
  Data in current interval (689 seconds elapsed):
     0 Line Code Violations, 0 Path Code Violations
     0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
  Total Data (last 24 hours)
     0 Line Code Violations, 0 Path Code Violations,
     0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,
     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs

If you need any more information on the configuration of the VG enter it, thank you very much.

Hall of Fame Super Gold

Re: Problem sending fax multiple pages through a VG224

Your  E1 config is correct. Try reducing fax speed to 9600 or 7200.

Re: Problem sending fax multiple pages through a VG224

ok.

I will try.


Thanks

Greetings

Bronze

Re: Problem sending fax multiple pages through a VG224

Hello Esteban,

If changing the baud rate does not work. Could you tell me where you are sending those calls to? Does that session target on the dial-peer

point to a different gateway? Also are other faxes working just not this particular fax? One thing you might try is on the voice class h323

is adujusting the h225 timeout tcp establish. To 10 or 12 should be suffiecent.

Hall of Fame Super Gold

Re: Problem sending fax multiple pages through a VG224

is adujusting the h225 timeout tcp establish. To 10 or 12 should be suffiecent.

Cannot be a TCP timeout problem, session gets established OK, and only drops after.

Bronze

Re: Problem sending fax multiple pages through a VG224

Yes that would be true, but I'm not sure that we have anything that indicates the session has been established.

Hall of Fame Super Gold

Re: Problem sending fax multiple pages through a VG224

OP clearly states:

I have problems sending FAX over 8 pages

Re: Problem sending fax multiple pages through a VG224

Hi

Try changing the speed of TX FAX, but FAX is old and there is the option .

Modify the parameter Establish the H225 tcp timeout to 11 (prior to what had to 3). Perform tests and all ok.


Thank you very much for your help.


Greetings

Hall of Fame Super Gold

Re: Problem sending fax multiple pages through a VG224

Very good, I'm suprised that it proved to be a timout problem.

Bronze

Re: Problem sending fax multiple pages through a VG224

You are welcome.

And just a friendly reminder to other posters that we need to ensure we keep the forums open to other suggestions no matter

how firmly we believe we know the issue so others ideas are not stifled.

Thanks,

Jay

Hall of Fame Super Gold

Re: Problem sending fax multiple pages through a VG224

And just a friendly reminder to other posters that we need to ensure we keep the forums open to other suggestions no matter

how firmly we believe we know the issue so others ideas are not stifled.

Certainly right.

Still would love to hear a logic explanation about how TCP timeout can affect multi-page fax

1581
Views
20
Helpful
12
Replies