Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

PVDM2-32 DSP Firmware ERROR!!!

<p>I have a 2811 ISR and put in a PVDM2-32 and configured the PRI and everything was good until I tried to make some calls.  I did some show voice dsp commands and I'm getting this error, can anyone point me in the right direction:</p>

<p>sh  voice dsp group all<br />

DSP groups on slot 0:<br />

dsp 1:<br />

  State: FAIL, firmware: 0.0.0<br />

  Max signal/voice channel: 16/16<br />

  Max credits: 240<br />

  num_of_sig_chnls_allocated: 16<br />

  Transcoding channels allocated: 0<br />

  Group: FLEX_GROUP_VOICE, complexity: FLEX<br />

    Shared credits: 240, reserved credits: 0<br />

    Signaling channels allocated: 16<br />

    Voice channels allocated: 0<br />

    Credits used: 0</p>

<p>dsp 2:<br />

  State: FAIL, firmware: 0.0.0<br />

  Max signal/voice channel: 16/16<br />

  Max credits: 240<br />

  num_of_sig_chnls_allocated: 9<br />

  Transcoding channels allocated: 0<br />

  Group: FLEX_GROUP_VOICE, complexity: FLEX<br />

    Shared credits: 240, reserved credits: 0<br />

    Signaling channels allocated: 9<br />

    Voice channels allocated: 0<br />

    Credits used: 0</p>

<p>  0 DSP resource allocation failure</p>

<p><br />

 sh  voice dsp voice</p>

<p>DSP  DSP                DSPWARE CURR  BOOT                         PAK     TX/RX</p>

<p>TYPE NUM CH CODEC       VERSION STATE STATE   RST AI VOICEPORT TS ABORT  PACK CO<br />

UNT<br />

==== === == ======== ========== ===== ======= === == ========= == ===== ========<br />

====<br />

edsp 0001 01 g729r8 p  0.1 IDLE  50/0/1.1<br />

edsp 0002 01 g729r8 p  0.1 IDLE  50/0/2.1<br />

edsp 0003 01 g729r8 p  0.1 IDLE  50/0/3.1<br />

edsp 0004 01 g729r8 p  0.1 IDLE  50/0/4.1</p>

<p>Warning! DSPs1, 2,  in slot 0 are using non-default firmware from flash:<br />

This is not recommended, the default version is 23.8.0</p>

<p>----------------------------FLEX VOICE CARD 0 ------------------------------<br />

                           *DSP VOICE CHANNELS*</p>

<p>CURR STATE : (busy)inuse (b-out)busy out (bpend)busyout pending<br />

LEGEND     : (bad)bad    (shut)shutdown  (dpend)download pending</p>

<p>DSP   DSP                 DSPWARE CURR  BOOT                         PAK   TX/RX</p>

<p>TYPE  NUM CH CODEC        VERSION STATE STATE   RST AI VOICEPORT TS ABRT PACK CO<br />

UNT<br />

===== === == ========= ========== ===== ======= === == ========= == ==== =======<br />

=====<br />

C5510 001 01 None           0.0.0 bad   idle      0  0                 0<br />

  0/0<br />

C5510 001 02 None           0.0.0 bad   idle      0  0                 0<br />

  0/0</p>

<p> </p>

3 REPLIES
Hall of Fame Super Gold

Re: PVDM2-32 DSP Firmware ERROR!!!

Hi, it after reseating the module (try a different slot) still problems, the PVDM2 is for RMA.

Re: PVDM2-32 DSP Firmware ERROR!!!

If you're on 12.4 code, this would be a hardware problem.  I believe we had some instances of things like this in 12.2-12.3 code with some software bugs.

 

Generally same as Paolo said - reseat the cards, and otherwise RMA the PVDM2-32.

 

-nick

New Member

Re: PVDM2-32 DSP Firmware ERROR!!!

Thanks all!

Working with tac now!

 

Thanks!

863
Views
5
Helpful
3
Replies