Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

PVDM3 with NM-HDV2 module

Hi guys,

We have a new 3945 running on IOS1 15.1.4M, it has one NM-HDV2-2T1/E1 and one PVDM3-64. I got following error message when I tried to create one E1 pri channel. We don't need any voice conferencing or transcode on this router. From the DSP calculator, it suggests me to use PVDM2-64 which should be sit on the NM-HDV2 module. Does it mean NM-HDV2 module can't use the PVDM3 resource on the router itself, or just NM-HDV2 module is not compatable with PVDM3?

% Not enough DSP resources available to configure pri-group on controller E1 4/0

% The remaining dsp resources are enough for 0 time slots.

% For current codec complexity, 2 extra 16 channel dsp(s) are required to create this voice port.

outcome from DSP calculator

Router: 3945
IOS: 15.1(4)M
DSP Modules Required:

PVDM2-64: 1

DSP Module Allocation:
Router Slot 4:60 Voice (94%) 4 Available (6%)

PVDM Slot 4/0: PVDM2-64

Call Volume Allocation:

LowMedHigh
Router Slot 4: NM-HDV2-2T1/E1(E1)60

Thanks. Leo

Everyone's tags (3)
1 ACCEPTED SOLUTION

Accepted Solutions
New Member

PVDM3 with NM-HDV2 module

Found the answer, issue following command, then the NM module can share the DSP resouce on mother board. Thanks for your replies.

Conf t

voice-card X

dspfarm

dsp services dspfarm

16 REPLIES
Blue

PVDM3 with NM-HDV2 module

HI

You cannot install PVDM3 modules directly on the  PVDM slots of an NM-HDV2, only the PVDM2s are supported by the NM-HDV2.  However, an NM-HDV2 that has no PVDMs installed at all can share PVDM3  DSP resources from the router motherboard PVDM slots across the chassis  backplane.

regards

Ronak Patel

rate helpful posts.

Regards Ronak Patel Rate all helpful post by clicking stars below the answer.
New Member

PVDM3 with NM-HDV2 module

Hi Ronak, Thanks for your reply.

So the NM-HDV2 should be able to use the PVDM3 on mother board, but why did I get the error said not enough DSP when I created the PRI channel?

Leo

Blue

PVDM3 with NM-HDV2 module

Hi Leo,

Have you installed it PVDM 3 on NM-HDV2 or on mother board?

Send the sh run of router if possible.

Regards

Ronak Patel

Please rate all informational posts also.

Regards Ronak Patel Rate all helpful post by clicking stars below the answer.
New Member

PVDM3 with NM-HDV2 module

Hi Ronak,

PVDM3 is installed on mother board. Here is the show run and show inventory

Current configuration : 5510 bytes

!

! Last configuration change at 05:24:50 UTC Thu Aug 9 2012 by test

! NVRAM config last updated at 05:20:38 UTC Thu Aug 9 2012 by test

! NVRAM config last updated at 05:20:38 UTC Thu Aug 9 2012 by test

version 15.1

service timestamps debug datetime msec

service timestamps log datetime msec

no service password-encryption

!

hostname SIP_GW

!

boot-start-marker

boot-end-marker

!

!

card type e1 4 1

logging buffered 51200 warnings

!

no aaa new-model

network-clock-participate slot 4

network-clock-select 1 E1 4/0

!

no ipv6 cef

ip source-route

ip cef

!

!

!

!

!

no ip domain lookup

ip domain name yourdomain.com

multilink bundle-name authenticated

!

!

!

!

isdn switch-type primary-net5

!

crypto pki token default removal timeout 0

!

crypto pki trustpoint TP-self-signed-2690548162

enrollment selfsigned

subject-name cn=IOS-Self-Signed-Certificate-2690548162

revocation-check none

rsakeypair TP-self-signed-2690548162

!

!

crypto pki certificate chain TP-self-signed-2690548162

certificate self-signed 01

  3082022B 30820194 A0030201 02020101 300D0609 2A864886 F70D0101 05050030

  31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D 43657274

  69666963 6174652D 32363930 35343831 3632301E 170D3132 30343235 31363534

  30315A17 0D323030 31303130 30303030 305A3031 312F302D 06035504 03132649

  4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D32 36393035

  34383136 3230819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281

  8100B635 4A275C3C E80C90CB 53495BF4 99A13A97 92005BDF E77AD34D 1970C635

  2077FC55 C550FBCB B43E821A D2FD4281 BB558238 05B625C4 3BC3B9B3 BA05CA8F

  556E30A4 61085C50 FCFA9C3E 3D33E035 5004DDB2 3BFB5CC7 F38A3760 17E6F5D2

  A652CC4F 4558FED1 48CCE4B3 83C10899 4F5615B4 93C8BC9E 71479168 FA16B4CB

  256B0203 010001A3 53305130 0F060355 1D130101 FF040530 030101FF 301F0603

  551D2304 18301680 1444A6AD 93B188D9 D47857FB 09A4DC0D 160D811F E8301D06

  03551D0E 04160414 44A6AD93 B188D9D4 7857FB09 A4DC0D16 0D811FE8 300D0609

  2A864886 F70D0101 05050003 8181000A BF09B52F 0CA5774A AC52FEB0 AAE211A8

  07AE7293 FB148E9E F4A66D0A E9D1ECBD CE0B9F10 F3D57C87 1CCD9A76 3CDB14DE

  2E278DBD 0017F95C 6C11AA93 F52EF8D3 8BD75391 6D0DD09A 90043ADF B3EDD363

  BF638D8B 408D8C54 E6EEA1F5 793F882D 02569368 E09308E9 0368CC78 F9DED390

  682D5389 437C4BEB CE3A963E 2082B8

            quit

voice-card 0

!

voice-card 4

!

!

!

!

!

!

!

hw-module pvdm 0/0

!

hw-module sm 4

!

!

!

!

redundancy

!

!

controller E1 4/0

!

controller E1 4/1

clock source internal

!

!

!

!

!

interface Embedded-Service-Engine0/0

no ip address

shutdown

!

interface GigabitEthernet0/0

description $ETH-LAN$$ETH-SW-LAUNCH$$INTF-INFO-GE 0/0$

ip address x.x.x.x

duplex auto

speed auto

!

interface GigabitEthernet0/1

no ip address

shutdown

duplex auto

speed auto

!

interface GigabitEthernet0/2

no ip address

shutdown

duplex auto

speed auto

!

ip forward-protocol nd

!

no ip http server

ip http authentication local

ip http secure-server

ip http timeout-policy idle 60 life 86400 requests 10000

!

!

!

nls resp-timeout 1

cpd cr-id 1

!

!

control-plane

!

!

!

!

mgcp profile default

!

!

!

!

!

gatekeeper

shutdown

!

!

banner exec ^C

% Password expiration warning.

-----------------------------------------------------------------------

Cisco Configuration Professional (Cisco CP) is installed on this device

and it provides the default username "cisco" for  one-time use. If you have

already used the username "cisco" to login to the router and your IOS image

supports the "one-time" user option, then this username has already expired.

You will not be able to login to the router with this username after you exit

this session.

It is strongly suggested that you create a new username with a privilege level

of 15 using the following command.

username privilege 15 secret 0

Replace and with the username and password you want to

use.

-----------------------------------------------------------------------

^C

banner login ^C

-----------------------------------------------------------------------

Cisco Configuration Professional (Cisco CP) is installed on this device.

This feature requires the one-time use of the username "cisco" with the

password "cisco". These default credentials have a privilege level of 15.

YOU MUST USE CISCO CP or the CISCO IOS CLI TO CHANGE THESE  PUBLICLY-KNOWN

CREDENTIALS

Here are the Cisco IOS commands.

username   privilege 15 secret 0

no username cisco

Replace and with the username and password you want

to use.

IF YOU DO NOT CHANGE THE PUBLICLY-KNOWN CREDENTIALS, YOU WILL NOT BE ABLE

TO LOG INTO THE DEVICE AGAIN AFTER YOU HAVE LOGGED OFF.

For more information about Cisco CP please follow the instructions in the

QUICK START GUIDE for your router or go to http://www.cisco.com/go/ciscocp

-----------------------------------------------------------------------

^C

!

line con 0

login local

line aux 0

line 2

no activation-character

no exec

transport preferred none

transport input all

transport output pad telnet rlogin lapb-ta mop udptn v120 ssh

stopbits 1

line vty 0 4

access-class 23 in

privilege level 15

login local

transport input telnet ssh

line vty 5 15

access-class 23 in

privilege level 15

login local

transport input telnet ssh

!

scheduler allocate 20000 1000

end

SIP_GW#sh inven

SIP_GW#sh inventory

NAME: "CISCO3945-CHASSIS", DESCR: "CISCO3945-CHASSIS"

PID: CISCO3945-CHASSIS , VID: V02, SN:

NAME: "Cisco Services Performance Engine 150 for Cisco 3900 ISR on Slot 0", DESCR: "Cisco Services Performance Engine 150 for Cisco 3900 ISR"

PID: C3900-SPE150/K9   , VID: V05 , SN:

NAME: "PVDM3 DSP DIMM with 64 Channels on Slot 0 SubSlot 4", DESCR: "PVDM3 DSP DIMM with 64 Channels"

PID: PVDM3-64          , VID: V01 , SN:

NAME: "Network Module Adapter for SM Slot on Slot 4", DESCR: "Network Module Adapter for SM Slot"

PID: SM-NM-ADPTR       , VID: V01, SN:

NAME: "High Density Voice2 Network module with on board two port interface  on Slot 4", DESCR: "High Density Voice2 Network module with on board two port interface "

PID: NM-HDV2-2T1/E1    , VID: V02 , SN:

NAME: "C3900 AC Power Supply 1", DESCR: "C3900 AC Power Supply 1"

PID: PWR-3900-AC       , VID: V03, SN:

Hall of Fame Super Gold

PVDM3 with NM-HDV2 module

What exactly are you trying to do? You don;t need the NM-HDV2-2T1/E1, but just a VWIC2 or VWIC3, and the PVDM3.

New Member

PVDM3 with NM-HDV2 module

Hi Paolo,

The story was the vendor didn't have VWIC2 or VWIC3 in stock then gave us the NM-HDV2-2T1/E1. Does it mean NM-HDV2 can't use the PVDM resource on mother borad?

Thanks. Leo

New Member

PVDM3 with NM-HDV2 module

There is no VWIC card on NM-HDV2-2T1/E1, we are trying to use the two E1 ports on NM module.

New Member

PVDM3 with NM-HDV2 module

Any documents from Cisco explain this situation?

New Member

PVDM3 with NM-HDV2 module

Found the answer, issue following command, then the NM module can share the DSP resouce on mother board. Thanks for your replies.

Conf t

voice-card X

dspfarm

dsp services dspfarm

New Member

PVDM3 with NM-HDV2 module

Hi, I do have the same problem, I cant configure the PRI, may you please to share your configuration?

thanks,

Cesar.

Hall of Fame Super Silver

PVDM3 with NM-HDV2 module

Post your config and "sh diag".

Chris

New Member

PVDM3 with NM-HDV2 module

Hi Deren

Here is the show run and show diag, I want the E1 NM to use the DSPs on the PVDM3 installed on the chasis instead of the PVDM2 on the NM. when I try to configure pri-group timeslots 1-31 this is the error message

% Not enough DSP resources available to configure pri-group on controller E1 1/0

% The remaining dsp resources are enough for 16 time slots.

% For current codec complexity, 1 extra 16 channel dsp(s) are required to create this voice port.


thanks in advance.

QUIRINAL_2911_GV#sh run

Building configuration...

Current configuration : 9445 bytes

!

version 15.2

service timestamps debug datetime msec localtime show-timezone

service timestamps log datetime msec localtime show-timezone

service password-encryption

!

hostname QUIRINAL_2911_GV

!

boot-start-marker

boot system flash:c2900-universalk9-mz.SPA.152-4.M1.bin

boot-end-marker

!

!

card type e1 1 1

logging buffered 51200 warnings

enable secret 4 ogRFA58sqtCqqOVz5pSvMHDQhNRAMsZX5zW5/gZcDgM

!

no aaa new-model

clock timezone GMT -5 0

network-clock-participate slot 1

!

!

!

!

!

!

!

ip domain name hocol.com.co

ip cef

no ipv6 cef

multilink bundle-name authenticated

!

!

!

!

isdn switch-type primary-net5

!

!

trunk group SALIDAPSTN

hunt-scheme random

!

!

trunk group SALIDACELULAR

hunt-scheme round-robin

!

!

crypto pki trustpoint TP-self-signed-2777551719

enrollment selfsigned

subject-name cn=IOS-Self-Signed-Certificate-2777551719

revocation-check none

rsakeypair TP-self-signed-2777551719

!

!

crypto pki certificate chain TP-self-signed-2777551719

certificate self-signed 01

  3082022B 30820194 A0030201 02020101 300D0609 2A864886 F70D0101 05050030

  31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D 43657274

  69666963 6174652D 32373737 35353137 3139301E 170D3132 30383231 31343030

  34365A17 0D323030 31303130 30303030 305A3031 312F302D 06035504 03132649

  4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D32 37373735

  35313731 3930819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281

  8100A5F7 7D661C44 C155D12A CB2FD246 F669F657 A24F143C A6AB41EE 71823E3C

  EFCDAEA2 97A1E39D 4ED052D7 64BEF94C EA5AF48F C5AE0D8F 7BB47557 FE5FA561

  B2FA8A44 220CF926 5D3CD01B AF900F87 F6321E7A 827A7781 E7FB461F C50BD1BA

  E207219D 3E465DDE 427C4E73 EE74DEFC 2252B8EC 3B3A7DEE 6723198E 94C21F6E

  CEAD0203 010001A3 53305130 0F060355 1D130101 FF040530 030101FF 301F0603

  551D2304 18301680 141C6606 3008C488 91F9BEB1 55C215BA A1E6AAF7 C9301D06

  03551D0E 04160414 1C660630 08C48891 F9BEB155 C215BAA1 E6AAF7C9 300D0609

  2A864886 F70D0101 05050003 8181008E 31468D48 BEF4E6E0 B1A39F45 238268DD

  460FACEB D3FB5EA8 9D2C6902 D89DA6DA 9097D504 AFB1C38D 83B31B06 05E14C08

  B875727C 319C13B4 BFA5972B CEEDD0FE 6C4F27E1 8350C5AF C86FADE2 416D3334

  ED053918 56AB6648 BC8E6519 A80FF32B D1D662CA 378F0D98 727E8C67 0E87CFDF

  2F45133F AA34876E 29556CE2 E4D28D

        quit

voice-card 0

dspfarm

dsp services dspfarm

!

voice-card 1

!

!

!

voice service voip

no ip address trusted authenticate

allow-connections h323 to h323

allow-connections h323 to sip

allow-connections sip to h323

allow-connections sip to sip

fax protocol pass-through g711ulaw

h323

modem passthrough nse codec g711ulaw

sip

  bind control source-interface GigabitEthernet0/0.102

  bind media source-interface GigabitEthernet0/0.102

!

voice class codec 1

codec preference 1 g711ulaw

codec preference 2 g711alaw

codec preference 3 g729r8

codec preference 4 ilbc

!

voice class codec 1000

codec preference 1 g729r8

codec preference 2 g729br8

codec preference 3 g723ar63

codec preference 4 g723r63

codec preference 5 g711alaw

codec preference 6 g711ulaw

!

!

!

!

!

!

license udi pid CISCO2911/K9 sn FTX1634AJ22

hw-module pvdm 0/0

!

hw-module sm 1

!

!

!

username hocvoip privilege 15 secret 4 ogRFA58sqtCqqOVz5pSvMHDQhNRAMsZX5zW5/gZcDgM

!

redundancy

!

!

controller E1 1/0

shutdown

!

controller E1 1/1

!

!

!

!        

!

interface Embedded-Service-Engine0/0

no ip address

shutdown

!

interface GigabitEthernet0/0

no ip address

duplex full

speed 1000

!

!

ip forward-protocol nd

!

ip http server

ip http access-class 23

ip http authentication local

ip http secure-server

ip http timeout-policy idle 60 life 86400 requests 10000

!

ip route 0.0.0.0 0.0.0.0 10.4.2.1

!

access-list 23 permit 10.10.10.0 0.0.0.7

!

!

!

control-plane

!        

!

voice-port 0/0/0

cptone CO

connection plar opx 6150

!

voice-port 0/0/1

cptone CO

connection plar opx 6119

!

voice-port 0/0/2

cptone CO

connection plar opx 6117

!

voice-port 0/0/3

cptone CO

connection plar opx 6151

!

voice-port 0/1/0

cptone CO

!

voice-port 0/1/1

!

voice-port 0/1/2

trunk-group SALIDAPSTN

supervisory disconnect dualtone mid-call

cptone CO

timeouts call-disconnect 5

timeouts wait-release 5

timing hookflash-out 500

!

voice-port 0/1/3

trunk-group SALIDAPSTN

supervisory disconnect dualtone mid-call

cptone CO

timeouts call-disconnect 5

timeouts wait-release 5

timing hookflash-out 500

!

voice-port 0/2/0

trunk-group SALIDACELULAR

supervisory disconnect dualtone mid-call

cptone CO

timeouts call-disconnect 5

timeouts wait-release 5

timing hookflash-out 500

caller-id enable

!

voice-port 0/2/1

trunk-group SALIDACELULAR

supervisory disconnect dualtone mid-call

cptone CO

timeouts call-disconnect 5

timeouts wait-release 5

timing hookflash-out 500

!

voice-port 0/2/2

trunk-group SALIDACELULAR

supervisory disconnect dualtone mid-call

cptone CO

timeouts call-disconnect 5

timeouts wait-release 5

timing hookflash-out 500

!

voice-port 0/2/3

trunk-group SALIDACELULAR

supervisory disconnect dualtone mid-call

cptone CO

timeouts call-disconnect 5

timeouts wait-release 5

timing hookflash-out 500

!

voice-port 0/3/0

!

voice-port 0/3/1

!

voice-port 0/3/2

!

voice-port 0/3/3

!

!

!

!

!

!

mgcp profile default

!

sccp local GigabitEthernet0/0.102

sccp ccm 10.0.3.15 identifier 1 priority 1 version 7.0

sccp ccm 10.0.3.6 identifier 2 priority 2 version 7.0

sccp ccm 10.0.3.5 identifier 3 priority 3 version 7.0

sccp

!

sccp ccm group 1

bind interface GigabitEthernet0/0.102

associate ccm 1 priority 1

associate ccm 2 priority 2

associate ccm 3 priority 3

associate profile 3 register CFBNEIVA

associate profile 2 register MTPNEIVA729

associate profile 1 register MTPNEIVA711

associate profile 4 register TXCNEIVA

!

dspfarm profile 1 mtp 

codec g711ulaw

maximum sessions software 100

associate application SCCP

!

dspfarm profile 2 mtp 

codec g729r8

maximum sessions software 100

associate application SCCP

!

dial-peer cor custom

name 1800

name local

name emergencia

name nacional

name celular

!

!

dial-peer cor list PermisoTotalSRST

member 1800

member local

member emergencia

member nacional

member celular

!

dial-peer cor list SalidaCelular

member celular

!

!

!

gatekeeper

shutdown

!

!

banner exec ^C

% Password expiration warning.

-----------------------------------------------------------------------

Cisco Configuration Professional (Cisco CP) is installed on this device

and it provides the default username "cisco" for  one-time use. If you have

already used the username "cisco" to login to the router and your IOS image

supports the "one-time" user option, then this username has already expired.

You will not be able to login to the router with this username after you exit

this session.

It is strongly suggested that you create a new username with a privilege level

of 15 using the following command.

username privilege 15 secret 0

Replace and with the username and password you want to

use.

-----------------------------------------------------------------------

^C

banner login ^C

-----------------------------------------------------------------------

Cisco Configuration Professional (Cisco CP) is installed on this device.

This feature requires the one-time use of the username "cisco" with the

password "cisco". These default credentials have a privilege level of 15.

YOU MUST USE CISCO CP or the CISCO IOS CLI TO CHANGE THESE  PUBLICLY-KNOWN

CREDENTIALS

Here are the Cisco IOS commands.

username   privilege 15 secret 0

no username cisco

Replace and with the username and password you want

to use.

IF YOU DO NOT CHANGE THE PUBLICLY-KNOWN CREDENTIALS, YOU WILL NOT BE ABLE

TO LOG INTO THE DEVICE AGAIN AFTER YOU HAVE LOGGED OFF.

For more information about Cisco CP please follow the instructions in the

QUICK START GUIDE for your router or go to http://www.cisco.com/go/ciscocp

-----------------------------------------------------------------------

^C

!

line con 0

password 7 104D0617241A41195D077E656A647F7F

login

line aux 0

line 2

no activation-character

no exec

transport preferred none

transport input all

transport output pad telnet rlogin lapb-ta mop udptn v120 ssh

stopbits 1

line vty 0 4

privilege level 15

login local

transport input telnet ssh

line vty 5 15

access-class 23 in

privilege level 15

login local

transport input telnet ssh

!

scheduler allocate 20000 1000

!

end

QUIRINAL_2911_GV# sh diag

Slot 0:

        C2911 Mother board 3GE, integrated VPN and 4W Port adapter, 19 ports

        Port adapter is analyzed

        Port adapter insertion time 01:15:41 ago

        EEPROM contents at hardware discovery:

        PCB Serial Number        : FOC163161FQ

        Hardware Revision        : 1.0

        Part Number              : 73-11833-09

        Top Assy. Part Number    : 800-30797-06

        Board Revision           : A0

        Deviation Number         : 0

        Fab Version              : 03

        Product (FRU) Number     : CISCO2911/K9

        Version Identifier       : V06

        CLEI Code                : CMMJD00ARA

        Processor type           : C1

        Chassis Serial Number    : FTX1634AJ22

        Chassis MAC Address      : 6073.5cd2.bcf0

        MAC Address block size   : 80

        Manufacturing Test Data  : 00 00 00 00 00 00 00 00

        EEPROM format version 4

        EEPROM contents (hex):

          0x00: 04 FF C1 8B 46 4F 43 31 36 33 31 36 31 46 51 40

          0x10: 06 18 41 01 00 82 49 2E 39 09 C0 46 03 20 00 78

          0x20: 4D 06 42 41 30 88 00 00 00 00 02 03 CB 8C 43 49

          0x30: 53 43 4F 32 39 31 31 2F 4B 39 89 56 30 36 20 D9

          0x40: 04 40 C1 CB C2 C6 8A 43 4D 4D 4A 44 30 30 41 52

          0x50: 41 09 C1 C2 8B 46 54 58 31 36 33 34 41 4A 32 32

          0x60: C3 06 60 73 5C D2 BC F0 43 00 50 C4 08 00 00 00

          0x70: 00 00 00 00 00 F3 00 03 40 01 25 FF FF FF FF FF

          0x80: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

          0x90: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

          0xA0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

          0xB0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

          0xC0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

          0xD0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

          0xE0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

          0xF0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

        Internal Power Supply information

        Top Assy. Part Number    : 341-0235-06

        Deviation Number         : 0

        PCB Serial Number        : AZS1628023J

        RMA Test History         : 00

        RMA Number               : 0-0-0-0

        RMA History              : 00

        Version Identifier       : V04

        Product (FRU) Number     : PWR-2911-AC

        CLEI Code                :

        Board Revision           : A0

        EEPROM format version 4

        EEPROM contents (hex):

          0x00: 04 FF 40 05 E5 DF 45 01 55 00 EB 06 88 00 00 00

          0x10: 00 C1 8B 41 5A 53 31 36 32 38 30 32 33 4A 03 00

          0x20: 81 00 00 00 00 04 00 89 56 30 34 20 CB 8B 50 57

          0x30: 52 2D 32 39 31 31 2D 41 43 C6 8A 00 00 00 00 00

          0x40: 00 00 00 00 00 F3 00 59 41 00 BE 42 00 05 F8 00

          0x50: 50 01 F4 17 2B 02 EE 1A 7A 03 E8 1B 65 04 E2 1C

          0x60: 47 05 DC 1C C9 06 D6 1D A3 07 D0 1E 54 08 CA 1E

          0x70: E6 09 C4 1F 5C 0A BE 1F BF 0B B8 20 12 0D AC 20

          0x80: 92 0F A0 20 F0 11 94 21 38 13 88 21 6B 17 70 21

          0x90: AE 1B 58 21 D3 1F 40 21 E0 23 28 21 DE 27 10 22

          0xA0: 56 42 41 30 FF FF FF FF FF FF FF FF FF FF FF FF

          0xB0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

          0xC0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

          0xD0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

          0xE0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

          0xF0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

        PVDM Slot 0:

        256-channel (G.711) Voice/Fax PVDM3 DSP DIMM PVDM daughter card

        Hardware Revision        : 1.0

        Part Number              : 73-11812-03

        Board Revision           : C0

        Deviation Number         : 0

        Fab Version              : 03

        PCB Serial Number        : FOC16316XL5

        RMA Test History         : 00

        RMA Number               : 0-0-0-0

        RMA History              : 00

        Processor type           : 00

        Product (FRU) Number     : PVDM3-256     

        Version Identifier       : V01

        EEPROM format version 4

        EEPROM contents (hex):

          0x00: 04 FF 40 05 DE 41 01 00 82 49 2E 24 03 42 43 30

          0x10: 88 00 00 00 00 02 03 C1 8B 46 4F 43 31 36 33 31

          0x20: 36 58 4C 35 03 00 81 00 00 00 00 04 00 09 00 CB

          0x30: 8F 50 56 44 4D 33 2D 32 35 36 20 20 20 20 20 20

          0x40: 89 56 30 31 20 D9 02 40 C1 FF FF FF FF FF FF FF

          0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

          0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

          0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

        WIC Slot 0:

        2nd generation - FXO Voice daughter card (4 port)

        Hardware Revision        : 5.0

        Top Assy. Part Number    : 800-33585-01

        Board Revision           : D0

        Deviation Number         : 0-0

        Fab Version              : 04

        PCB Serial Number        : FOC16294SUV

        RMA Test History         : 00

        RMA Number               : 0-0-0-0

        RMA History              : 00

        Product (FRU) Number     : VIC2-4FXO

        Version Identifier       : V04

        CLEI Code                : CNUIAXJAAC

        EEPROM format version 4

        EEPROM contents (hex):

          0x00: 04 FF 40 00 4C 41 05 00 C0 46 03 20 00 83 31 01

          0x10: 42 44 30 80 00 00 00 00 02 04 C1 8B 46 4F 43 31

          0x20: 36 32 39 34 53 55 56 03 00 81 00 00 00 00 04 00

          0x30: CB 89 56 49 43 32 2D 34 46 58 4F 89 56 30 34 20

          0x40: C6 8A 43 4E 55 49 41 58 4A 41 41 43 FF FF FF FF

          0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

          0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

          0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

        WIC Slot 1:

        2nd generation - FXO Voice daughter card (4 port)

        Hardware Revision        : 5.0

        Top Assy. Part Number    : 800-33585-01

        Board Revision           : D0

        Deviation Number         : 0-0

        Fab Version              : 04

        PCB Serial Number        : FOC16294T3B

        RMA Test History         : 00

        RMA Number               : 0-0-0-0

        RMA History              : 00

        Product (FRU) Number     : VIC2-4FXO

        Version Identifier       : V04

        CLEI Code                : CNUIAXJAAC

        EEPROM format version 4

        EEPROM contents (hex):

          0x00: 04 FF 40 00 4C 41 05 00 C0 46 03 20 00 83 31 01

          0x10: 42 44 30 80 00 00 00 00 02 04 C1 8B 46 4F 43 31

          0x20: 36 32 39 34 54 33 42 03 00 81 00 00 00 00 04 00

          0x30: CB 89 56 49 43 32 2D 34 46 58 4F 89 56 30 34 20

          0x40: C6 8A 43 4E 55 49 41 58 4A 41 41 43 FF FF FF FF

          0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

          0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

          0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

        WIC Slot 2:

        2nd generation - FXO Voice daughter card (4 port)

        Hardware Revision        : 5.0

        Top Assy. Part Number    : 800-33585-01

        Board Revision           : D0

        Deviation Number         : 0-0

        Fab Version              : 04

        PCB Serial Number        : FOC16294TCW

        RMA Test History         : 00

        RMA Number               : 0-0-0-0

        RMA History              : 00

        Product (FRU) Number     : VIC2-4FXO

        Version Identifier       : V04

        CLEI Code                : CNUIAXJAAC

        EEPROM format version 4

        EEPROM contents (hex):

          0x00: 04 FF 40 00 4C 41 05 00 C0 46 03 20 00 83 31 01

          0x10: 42 44 30 80 00 00 00 00 02 04 C1 8B 46 4F 43 31

          0x20: 36 32 39 34 54 43 57 03 00 81 00 00 00 00 04 00

          0x30: CB 89 56 49 43 32 2D 34 46 58 4F 89 56 30 34 20

          0x40: C6 8A 43 4E 55 49 41 58 4A 41 41 43 FF FF FF FF

          0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

          0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

          0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

        WIC Slot 3:

        3rd generation - FXS DID Voice daughter card (4 port)

        Hardware Revision        : 1.0

        Top Assy. Part Number    : 800-33583-01

        Board Revision           : E0

        Deviation Number         : 0

        Fab Version              : 07

        PCB Serial Number        : FOC16304UNV

        RMA Test History         : 00

        RMA Number               : 0-0-0-0

        RMA History              : 00

        Product (FRU) Number     : VIC3-4FXS/DID

        Version Identifier       : V03

        CLEI Code                : IPUIA6JRAC

        Longitudinal Calibration : 01 10 10 53 87 10 10 5B

                                   8C 10 10 82 98 10 10 A7

                                   7B

        EEPROM format version 4

        EEPROM contents (hex):

          0x00: 04 FF 40 05 1B 41 01 00 C0 46 03 20 00 83 2F 01

          0x10: 42 45 30 88 00 00 00 00 02 07 C1 8B 46 4F 43 31

          0x20: 36 33 30 34 55 4E 56 03 00 81 00 00 00 00 04 00

          0x30: CB 8D 56 49 43 33 2D 34 46 58 53 2F 44 49 44 89

          0x40: 56 30 33 20 D9 02 40 C1 C6 8A 49 50 55 49 41 36

          0x50: 4A 52 41 43 D3 11 01 10 10 53 87 10 10 5B 8C 10

          0x60: 10 82 98 10 10 A7 7B FF FF FF FF FF FF FF FF FF

          0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

Slot 1:

        SM-NM-ADPTR

        Port Adapter is analyzed

        Port Adapter insertion time 01:15:41 ago

        EEPROM contents at hardware discovery:

        PCB Serial Number        : FOC16311KE3

        Hardware Revision        : 1.0

        Part Number              : 73-12434-04

        Top Assy. Part Number    : 800-32481-01

        Board Revision           : G0

        Deviation Number         : 0

        Fab Version              : 05

        RMA Test History         : 00

        RMA Number               : 0-0-0-0

        RMA History              : 00

        Product (FRU) Number     : SM-NM-ADPTR

        Version Identifier       : V01

        EEPROM format version 4

        EEPROM contents (hex):

          0x00: 04 FF C1 8B 46 4F 43 31 36 33 31 31 4B 45 33 40

          0x10: 05 F4 41 01 00 82 49 30 92 04 C0 46 03 20 00 7E

          0x20: E1 01 42 47 30 88 00 00 00 00 02 05 03 00 81 00

          0x30: 00 00 00 04 00 CB 8B 53 4D 2D 4E 4D 2D 41 44 50

          0x40: 54 52 89 56 30 31 00 D9 03 40 C1 CB F3 00 03 40

          0x50: 0B E3 FF FF FF FF FF FF FF FF FF FF FF FF FF FF

          0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

          0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

        High Density Voice NM-HDV2-2T1/E1 Port adapter

        Port adapter is analyzed

        Port adapter insertion time 01:15:15 ago

        EEPROM contents at hardware discovery:

        Hardware Revision        : 1.1

        Top Assy. Part Number    : 800-22168-05

        Board Revision           : E0

        Deviation Number         : 0

        Fab Version              : 05

        PCB Serial Number        : FOC162737UL

        RMA Test History         : 00

        RMA Number               : 0-0-0-0

        RMA History              : 00

        Fab Part Number          : 28-6126-05

        Manufacturing Test Data  : 00 00 00 00 00 00 00 00

        Field Diagnostics Data   : 00 00 00 00 00 00 00 00

        Product (FRU) Number     : NM-HDV2-2T1/E1

        Version Identifier       : V05

        EEPROM format version 4

        EEPROM contents (hex):

          0x00: 04 FF 40 03 DB 41 01 01 C0 46 03 20 00 56 98 05

          0x10: 42 45 30 88 00 00 00 00 02 05 C1 8B 46 4F 43 31

          0x20: 36 32 37 33 37 55 4C 03 00 81 00 00 00 00 04 00

          0x30: 85 1C 17 EE 05 C4 08 00 00 00 00 00 00 00 00 C5

          0x40: 08 00 00 00 00 00 00 00 00 CB 8E 4E 4D 2D 48 44

          0x50: 56 32 2D 32 54 31 2F 45 31 89 56 30 35 20 D9 02

          0x60: 40 C1 FF FF FF FF FF FF FF FF FF FF FF FF FF FF

          0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

        FPGA revision:0x16C

        WIC Slot 1:

        HDV2 on board t1/e1 controller (2 port)

        PVDM Slot 0:

        16-channel (G.711) Voice/Fax PVDMII DSP SIMM PVDM daughter card

        Hardware Revision        : 4.0

        Part Number              : 73-8538-05

        Board Revision           : C0

        Deviation Number         : 0

        Fab Version              : 04

        PCB Serial Number        : FOC16313R00

        RMA Test History         : 00

        RMA Number               : 0-0-0-0

        RMA History              : 00

        Processor type           : 00

        Product (FRU) Number     : PVDM2-16

        Version Identifier       : V01

        EEPROM format version 4

        EEPROM contents (hex):

          0x00: 04 FF 40 03 EF 41 04 00 82 49 21 5A 05 42 43 30

          0x10: 88 00 00 00 00 02 04 C1 8B 46 4F 43 31 36 33 31

          0x20: 33 52 30 30 03 00 81 00 00 00 00 04 00 09 00 CB

          0x30: 88 50 56 44 4D 32 2D 31 36 89 56 30 31 20 D9 02

          0x40: 40 C1 FF FF FF FF FF FF FF FF FF FF FF FF FF FF

          0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

          0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

          0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

Embedded Service Engine 0/0 :

  Total platform memory : 524288K bytes

  Total 2nd core memory : 0K bytes

  Start of physical address for 2nd core : 0x80000000

  Virtual address start of 2nd core memory : 0x0 - 0x0

  2nd core configured disabled

  L2 cache ways for 2nd core : 0

QUIRINAL_2911_GV# 

Hall of Fame Super Silver

PVDM3 with NM-HDV2 module

You need to remove the PVDM2-16 from the HDV card in order to use the PVDM3 from motherboard. Per:

Q. Are the PVDM3 modules supported in a NM-HDV2?

A. No. You cannot install PVDM3 modules directly on the PVDM slots of an NM-HDV2, only the PVDM2s are supported by the NM-HDV2. However, an NM-HDV2 that has no PVDMs installed at all can share PVDM3 DSP resources from the router motherboard PVDM slots across the chassis backplane.

http://www.cisco.com/en/US/prod/collateral/modules/ps3115/qa_c67_553073_ps10537_Products_Q_and_A_Item.html

As it stands the router is trying to allocate the PVDM2-16 first which is not enough for PVDMs.

HTH, pleae rate all useful posts!

Chris

VIP Super Bronze

PVDM3 with NM-HDV2 module

Cesar,

You can also send the output of

show voice dsp group all...

This will let us know what resources you have left on your PVDM3-256. As Chris, you need to remove the PVDM2-16, but you also need to know what you have left on the PVDM3-256. So send the output of that command

Please rate all useful posts

"'Nature is too thin a screen, the glory of the omnipresent God bursts through it everywhere"-Ralph Waldo Emerson

Please rate all useful posts "The essence of christianity is not the enthronement but the obliteration of self --William Barclay"
New Member

PVDM3 with NM-HDV2 module

Cesar,

Following command fixed my issue, but seems yours is different since you have one PVDM on NM module. As Chris suggest, you may need to remvoe the PVDM from NM module then give it a try.

Conf t

voice-card X

dspfarm

dsp services dspfarm

Cheers, Leo

Hall of Fame Super Silver

PVDM3 with NM-HDV2 module

He is already sharing PVDMs on voice-card 0 and he should not be sharing voice-card 1. There is no silver bullet solution here, remove PVDM2-16 and desired outcome will come.

Chris

3476
Views
15
Helpful
16
Replies