Cisco Support Community
Showing results for 
Search instead for 
Did you mean: 

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

"Dial-peer cor list" command not working


I have a cisco 891 router having c890-universalk9-mz.152-4.M4.bin IOS,

Show version

voice-gw#sh ver

Cisco IOS Software, C890 Software (C890-UNIVERSALK9-M), Version 15.2(4)M4, RELEASE SOFTWARE (fc2)

Technical Support:

Copyright (c) 1986-2013 by Cisco Systems, Inc.

Compiled Thu 20-Jun-13 17:06 by prod_rel_team

ROM: System Bootstrap, Version 12.4(22r)YB3, RELEASE SOFTWARE (fc1)

multinet-voice-gw uptime is 2 weeks, 6 days, 21 hours, 59 minutes

System returned to ROM by power-on

System image file is "flash:c890-universalk9-mz.152-4.M4.bin"

Last reload type: Normal Reload

Last reload reason: power-on

This product contains cryptographic features and is subject to United

States and local country laws governing import, export, transfer and

use. Delivery of Cisco cryptographic products does not imply

third-party authority to import, export, distribute or use encryption.

Importers, exporters, distributors and users are responsible for

compliance with U.S. and local country laws. By using this product you

agree to comply with applicable laws and regulations. If you are unable

to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:

If you require further assistance please contact us by sending email to

Cisco 891 (MPC8300) processor (revision 1.0) with 498688K/25600K bytes of memory.

Processor board ID FCZ173992T4

9 FastEthernet interfaces

1 Gigabit Ethernet interface

1 Serial interface

1 terminal line

1 Virtual Private Network (VPN) Module

256K bytes of non-volatile configuration memory.

250880K bytes of ATA CompactFlash (Read/Write)

License Info:

License UDI:


Device#   PID                   SN


*0        CISCO891-K9           FCZ173992T4    

License Information for 'c890'

    License Level: advipservices   Type: Permanent

    Next reboot license Level: advipservices

Configuration register is 0x2102

i want to implement COR list but Dial-peer cor custom command is not working.

voice-gw(config)#dial-peer ?

  data        Data type

  hunt        Define the dial peer hunting choice

  inbound     Define the inbound options

  no-match    Define the disconnect cause for no dialpeer match

  outbound    Define the outbound options

  search      Define dial peer search service

  terminator  Define the address terminate character

  voice       Voice type

It doesnt show COR? what could be the reason?



"Dial-peer cor list" command not working

Global info about COR:

I think your router doesn't support this...


HTH, Dragan
New Member

"Dial-peer cor list" command not working

Thanks for your response. Is there any cisco document which says cisco 891 router doesnt support COR? I have checked IOS and it does support cor list commands.


"Dial-peer cor list" command not working

The only best source - Cisco Feature navigator

Check there to be sure 100%...


HTH, Dragan
New Member

"Dial-peer cor list" command not working

Show dial-peer cor command works on same router but doesnt work on configuration mode ..strange!

voice-gw#sh dial-peer cor

Class of Restriction


New Member

"Dial-peer cor list" command not working

Problem solved after changing IOS, there might be bug in previous IOS and is not mention any where in cisco docs. after copying latest version c890-universalk9-mz.154-1.T1.bin, dial-peer cor command works!


"Dial-peer cor list" command not working


Good info...


HTH, Dragan