Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

"Ring Out" shown on IP Phone but no ringing tone

Hi,

I am having a problem where i have a QSIG connection between a Cisco 3845 and a Nortel Option 11C PBX. This router is configured as H323 registered to a CallManager 4.2(3)

When I use an IP phone and dial to a nortel phone.

The nortel phone is ringing, but I do not hear the ringing on the IP phone. There is a message "Ring Out" on the IP phone.

When I do a debug isdn q931 on the router, this is what I see:

Router#

Jan 21 23:33:36 SG: ISDN Se0/1/0:15 Q931: Applying typeplan for sw-type 0x16 is 0x0 0x0, Calling num 83181713

Jan 21 23:33:36 SG: ISDN Se0/1/0:15 Q931: Applying typeplan for sw-type 0x16 is 0x0 0x0, Called num 1708

Jan 21 23:33:36 SG: ISDN Se0/1/0:15 Q931: TX -> SETUP pd = 8 callref = 0x0006

Bearer Capability i = 0x8090A3

Standard = CCITT

Transfer Capability = Speech

Transfer Mode = Circuit

Transfer Rate = 64 kbit/s

Channel ID i = 0xA98381

Exclusive, Channel 1

Calling Party Number i = 0x0081, '1000'

Plan:Unknown, Type:Unknown

Called Party Number i = 0x80, '2000'

Plan:Unknown, Type:Unknown

SGHQGA2-3845#

Jan 21 23:33:36 SG: ISDN Se0/1/0:15 Q931: RX <- SETUP_ACK pd = 8 callref = 0x8006

Channel ID i = 0xA98381

Exclusive, Channel 1

Jan 21 23:33:36 SG: ISDN Se0/1/0:15 Q931: RX <- CALL_PROC pd = 8 callref = 0x8006

Jan 21 23:33:36 SG: ISDN Se0/1/0:15 Q931: RX <- ALERTING pd = 8 callref = 0x8006

Locking Shift to Codeset 5

Codeset 5 IE 0x32 i = 0x81

Here is a partial Configuration of the QSIG connection.

interface Serial0/1/0:15

no ip address

no ip redirects

no ip unreachables

no ip proxy-arp

no ip route-cache cef

no ip route-cache

no logging event link-status

isdn switch-type primary-qsig

isdn protocol-emulate network

isdn incoming-voice voice

no isdn T309-enable

isdn T310 120000

no cdp enable

Hope someone can help on this.

Thanks,

Eugene

4 REPLIES

Re: "Ring Out" shown on IP Phone but no ringing tone

New Member

Re: "Ring Out" shown on IP Phone but no ringing tone

This may be that old chestnut "isdn progress indicators". Try

progress_ind alert enable 8

under the outbound dial peer.

You may also need

progress_ind setup enable 3

on the inbound dial peer if there are ringback problems the other way

New Member

Re: "Ring Out" shown on IP Phone but no ringing tone

Thanks both, I will try this out. :)

Appreciate it.

Eugene

New Member

Re: "Ring Out" shown on IP Phone but no ringing tone

Thanks!

The progress_ind solved the problem.

The H225 service parameter had no efffect.

Thanks all!

learnt something today.

:)

Eugene

471
Views
12
Helpful
4
Replies