Buy or Renew
Buy or Renew
Cisco + Splunk: It’s a new day for your data. Learn more.
 
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation
1231
Views
0
Helpful
3
Replies

Rightfax integration with Cisco VG over PRI trunk

Go to solution
Risat
Level 3
Level 3

‎07-18-2012 03:13 AM - edited ‎03-16-2019 12:15 PM

Hi,

Anybody has done the integration mentioned in the subject line. My layer 1 is showing active but layer 2 status is showing TEI_ASSIGNED. Configuration has been attached. Any help would be greatly appreciated.

Labels:
131790-RightFax-VG-1.log.zip
0 Helpful
1 Accepted Solution

Accepted Solutions

Go to solution
acampbell
VIP Alumni
VIP Alumni

‎07-18-2012 03:25 AM

Mohammed,

I doubt very much if the rightfax end of the PRI will be the network end.

Change you config at the router end to be the NETWORK

!

interface Serial0/0/1:15

shut

description ### E1 PRI connected to RIGHTFAX ###

no ip address

encapsulation hdlc

isdn switch-type primary-net5

isdn incoming-voice voice

no cdp enable

isdn protocol-emulate network

no shut

!

show isdn status

See how this goes

Regards,
Alex.
Please rate useful posts.

Regards, Alex. Please rate useful posts.

View solution in original post

0 Helpful
3 Replies 3

Go to solution
acampbell
VIP Alumni
VIP Alumni

‎07-18-2012 03:25 AM

Mohammed,

I doubt very much if the rightfax end of the PRI will be the network end.

Change you config at the router end to be the NETWORK

!

interface Serial0/0/1:15

shut

description ### E1 PRI connected to RIGHTFAX ###

no ip address

encapsulation hdlc

isdn switch-type primary-net5

isdn incoming-voice voice

no cdp enable

isdn protocol-emulate network

no shut

!

show isdn status

See how this goes

Regards,
Alex.
Please rate useful posts.

Regards, Alex. Please rate useful posts.
0 Helpful

Go to solution
Risat
Level 3
Level 3
In response to acampbell

‎07-25-2012 11:46 PM

Layer 2 is mulitframe established after adding the below command, but now the call goes through From VG to Right FAX only once in a while and viceversa also is not working. It keeps giving busy signal. Below is the debug isdn outputs.

debug isdn q931


RIGHTFAX-VG#

*Jul 18 15:37:51.671: ISDN Se0/0/1:15 Q931: TX -> RELEASE_COMP pd = 8  callref = 0x00D6

Cause i = 0x80E6 - Recovery on timer expiry

*Jul 18 15:37:54.387: ISDN Se0/0/0:15 Q931: RX <- SETUP pd = 8  callref = 0x21E2

Sending Complete

Bearer Capability i = 0x9090A3

Standard = CCITT

Transfer Capability = 3.1kHz Audio

Transfer Mode = Circuit

Transfer Rate = 64 kbit/s

Channel ID i = 0xA18392

Preferred, Channel 18

Progress Ind i = 0x8283 - Origination address is non-ISDN 

Calling Party Number i = 0x2183, '026423000'

Plan:ISDN, Type:National

Called Party Number i = 0xC1, '106'

Plan:ISDN, Type:Subscriber(local)

*Jul 18 15:37:54.387: ISDN Se0/0/0:15 Q931: Received SETUP  callref = 0xA1E2 callID = 0x0021 switch = primary-net5 interface = User

*Jul 18 15:37:54.387: ISDN Se0/0/1:15 Q931: Applying typeplan for sw-type 0x12 is 0x2 0x1, Calling num 9026423000

*Jul 18 15:37:54.387: ISDN Se0/0/1:15 Q931: Sending SETUP  callref = 0x00D7 callID = 0x8013 switch = primary-net5 interface = Network

*Jul 18 15:37:54.387: ISDN Se0/0/0:15 Q931: TX -> CALL_PROC pd = 8  callref = 0xA1E2

Channel ID i = 0xA98392

Exclusive, Channel 18

*Jul 18 15:37:54.387: ISDN Se0/0/1:15 Q931: TX -> SETUP pd = 8  callref = 0x00D7

Sending Complete

Bearer Capability i = 0x9090A3

Standard = CCITT

Transfer Capability = 3.1kHz Audio

Transfer Mode = Circuit

Transfer Rate = 64 kbit/s

Channel ID i = 0xA98381

Exclusive, Channel 1

Progress Ind i = 0x8283 - Origination address is non-ISDN 

Calling Party Number i = 0x2183, '9026423000'

Plan:ISDN, Type:National

Called Party Number i = 0xC1, '4160106'

Plan:ISDN, Type:Subscriber(local)

*Jul 18 15:37:55.387: ISDN Se0/0/1:15 Q931: TX -> SETUP pd = 8  callref = 0x00D7

Sending Complete

Bearer Capability i = 0x9090A3

Standard = CCITT

Transfer Capability = 3.1kHz Audio

Transfer Mode = Circuit

Transfer Rate = 64 kbit/s

Channel ID i = 0xA98381

Exclusive, Channel 1

Progress Ind i = 0x8283 - Origination address is non-ISDN 

Calling Party Number i = 0x2183, '9026423000'

Plan:ISDN, Type:National

Called Party Number i = 0xC1, '4160106'

Plan:ISDN, Type:Subscriber(local)

*Jul 18 15:37:56.387: ISDN Se0/0/1:15 Q931: TX -> SETUP pd = 8  callref = 0x00D7

Sending Complete

Bearer Capability i = 0x9090A3

Standard = CCITT

Transfer Capability = 3.1kHz Audio

Transfer Mode = Circuit

Transfer Rate = 64 kbit/s

Channel ID i = 0xA98381

Exclusive, Channel 1

Progress Ind i = 0x8283 - Origination address is non-ISDN 

Calling Party Number i = 0x2183, '9026423000'

Plan:ISDN, Type:National

Called Party Number i = 0xC1, '4160106'

Plan:ISDN, Type:Subscriber(local)

*Jul 18 15:37:56.771: ISDN Se0/0/1:15 Q931: RX <- RELEASE pd = 8  callref = 0x0001

Cause i = 0x8090 - Normal call clearing

*Jul 18 15:37:56.771: ISDN Se0/0/1:15 **ERROR**: L3_BadPeerMsg: event 0x4D cr 0x8001 callid 0x0

*Jul 18 15:37:57.387: ISDN Se0/0/1:15 Q931: TX -> SETUP pd = 8  callref = 0x00D7

Sending Complete

Bearer Capability i = 0x9090A3

Standard = CCITT

Transfer Capability = 3.1kHz Audio

Transfer Mode = Circuit

Transfer Rate = 64 kbit/s

Channel ID i = 0xA98381

Exclusive, Channel 1

Progress Ind i = 0x8283 - Origination address is non-ISDN 

Calling Party Number i = 0x2183, '9026423000'

Plan:ISDN, Type:National

Called Party Number i = 0xC1, '4160106'

Plan:ISDN, Type:Subscriber(local)

*Jul 18 15:38:00.771: ISDN Se0/0/1:15 Q931: RX <- RELEASE pd = 8  callref = 0x0001

Cause i = 0x8090 - Normal call clearing

*Jul 18 15:38:00.771: ISDN Se0/0/1:15 **ERROR**: L3_BadPeerMsg: event 0x4D cr 0x8001 callid 0x0

*Jul 18 15:38:00.771: ISDN Se0/0/1:15 Q931: TX -> RELEASE_COMP pd = 8  callref = 0x8001

Cause i = 0x80D1 - Invalid call reference value

*Jul 18 15:38:01.771: ISDN Se0/0/1:15 Q931: TX -> RELEASE_COMP pd = 8  callref = 0x8001

Cause i = 0x80D1 - Invalid call reference value

*Jul 18 15:38:02.387: ISDN Se0/0/1:15 **ERROR**: CCPCC_CallOrigination: SETUP timed-out (2nd T303) to NETWORK.  The SETUP failed.

*Jul 18 15:38:02.387: ISDN Se0/0/0:15 Q931: TX -> DISCONNECT pd = 8  callref = 0xA1E2

Cause i = 0x8092 - No user responding

*Jul 18 15:38:02.555: ISDN Se0/0/0:15 Q931: RX <- RELEASE pd = 8  callref = 0x21E2

*Jul 18 15:38:02.555: ISDN Se0/0/0:15 Q931: TX -> RELEASE_COMP pd = 8  callref = 0xA1E2

*Jul 18 15:38:02.771: ISDN Se0/0/1:15 Q931: TX -> RELEASE_COMP pd = 8  callref = 0x8001

Cause i = 0x80D1 - Invalid call reference value

*Jul 18 15:38:02.775: ISDN Se0/0/1:15 Q931: TX -> RELEASE_COMP pd = 8  callref = 0x00D7

Cause i = 0x80E6 - Recovery on timer expiry

debug isdn q921

*Jul 18 14:22:24.555: ISDN Se0/0/1:15 Q921: Net RX <- RRp sapi=0 tei=0 nr=1

*Jul 18 14:22:24.999: ISDN Se0/0/1:15 Q921: Net TX -> SABMEp sapi=0 tei=0

*Jul 18 14:22:24.999: ISDN Se0/0/1:15 Q921: Net RX <- UAf sapi=0 tei=0

*Jul 18 14:22:27.999: ISDN Se0/0/1:15 Q921: Net TX -> INFO sapi=0 tei=0, ns=0 nr=0

*Jul 18 14:22:27.999: ISDN Se0/0/1:15 **ERROR**: CCPCC_CallOrigination: SETUP timed-out (2nd T303) to NETWORK.  The SETUP failed.

*Jul 18 14:22:27.999: ISDN Se0/0/0:15 Q921: User TX -> INFO sapi=0 tei=0, ns=28 nr=19

*Jul 18 14:22:28.023: ISDN Se0/0/0:15 Q921: User RX <- RR sapi=0 tei=0 nr=29

*Jul 18 14:22:28.155: ISDN Se0/0/0:15 Q921: User RX <- INFO sapi=0 tei=0, ns=19 nr=29

*Jul 18 14:22:28.155: ISDN Se0/0/0:15 Q921: User TX -> RR sapi=0 tei=0 nr=20

*Jul 18 14:22:28.155: ISDN Se0/0/0:15 Q921: User TX -> INFO sapi=0 tei=0, ns=29 nr=20

*Jul 18 14:22:28.179: ISDN Se0/0/0:15 Q921: User RX <- RR sapi=0 tei=0 nr=30

*Jul 18 14:22:28.999: ISDN Se0/0/1:15 Q921: S7_T200_EXPIRY: VA = 0, VS = 1

*Jul 18 14:22:28.999: ISDN Se0/0/1:15 Q921: Net TX -> INFOp sapi=0 tei=0, ns=0 nr=0

*Jul 18 14:22:29.999: ISDN Se0/0/1:15 Q921: Net TX -> INFOp sapi=0 tei=0, ns=0 nr=0

*Jul 18 14:22:30.999: ISDN Se0/0/1:15 Q921: Net TX -> INFOp sapi=0 tei=0, ns=0 nr=0

*Jul 18 14:22:31.999: ISDN Se0/0/1:15 Q921: L2_EstablishDataLink: sending SABME

*Jul 18 14:22:31.999: ISDN Se0/0/1:15 Q921: Net TX -> SABMEp sapi=0 tei=0

*Jul 18 14:22:32.999: ISDN Se0/0/1:15 Q921: Net TX -> SABMEp sapi=0 tei=0

*Jul 18 14:22:32.999: ISDN Se0/0/1:15 Q921: Net RX <- UAf sapi=0 tei=0

*Jul 18 14:22:36.791: ISDN Se0/0/0:15 Q921: User RX <- INFO sapi=0 tei=0, ns=20 nr=30

*Jul 18 14:22:36.791: ISDN Se0/0/0:15 Q921: User TX -> RR sapi=0 tei=0 nr=21

*Jul 18 14:22:36.791: ISDN Se0/0/0:15 Q921: User TX -> INFO sapi=0 tei=0, ns=30 nr=21

*Jul 18 14:22:36.791: ISDN Se0/0/1:15 Q921: Net TX -> INFO sapi=0 tei=0, ns=0 nr=0

*Jul 18 14:22:36.815: ISDN Se0/0/0:15 Q921: User RX <- RR sapi=0 tei=0 nr=31

*Jul 18 14:22:37.791: ISDN Se0/0/1:15 Q921: S7_T200_EXPIRY: VA = 0, VS = 1

*Jul 18 14:22:37.791: ISDN Se0/0/1:15 Q921: Net TX -> INFOp sapi=0 tei=0, ns=0 nr=0

*Jul 18 14:22:38.791: ISDN Se0/0/1:15 Q921: Net TX -> INFOp sapi=0 tei=0, ns=0 nr=0

*Jul 18 14:22:39.791: ISDN Se0/0/1:15 Q921: Net TX -> INFOp sapi=0 tei=0, ns=0 nr=0

*Jul 18 14:22:40.791: ISDN Se0/0/1:15 Q921: L2_EstablishDataLink: sending SABME

*Jul 18 14:22:40.791: ISDN Se0/0/1:15 Q921: Net TX -> SABMEp sapi=0 tei=0

*Jul 18 14:22:41.791: ISDN Se0/0/1:15 Q921: Net TX -> SABMEp sapi=0 tei=0

*Jul 18 14:22:42.791: ISDN Se0/0/1:15 Q921: Net TX -> SABMEp sapi=0 tei=0

*Jul 18 14:22:42.791: ISDN Se0/0/1:15 Q921: Net RX <- UAf sapi=0 tei=0

*Jul 18 14:22:44.791: ISDN Se0/0/1:15 Q921: Net TX -> INFO sapi=0 tei=0, ns=0 nr=0

*Jul 18 14:22:44.791: ISDN Se0/0/1:15 **ERROR**: CCPCC_CallOrigination: SETUP timed-out (2nd T303) to NETWORK.  The SETUP failed.

*Jul 18 14:22:44.791: ISDN Se0/0/0:15 Q921: User TX -> INFO sapi=0 tei=0, ns=31 nr=21

*Jul 18 14:22:44.815: ISDN Se0/0/0:15 Q921: User RX <- RR sapi=0 tei=0 nr=32

*Jul 18 14:22:44.943: ISDN Se0/0/0:15 Q921: User RX <- INFO sapi=0 tei=0, ns=21 nr=32

*Jul 18 14:22:44.943: ISDN Se0/0/0:15 Q921: User TX -> RR sapi=0 tei=0 nr=22

0 Helpful

Go to solution
acampbell
VIP Alumni
VIP Alumni
In response to Risat

‎07-26-2012 06:33 AM

Hi

Jul 18 15:37:56.771: ISDN Se0/0/1:15 **ERROR**: L3_BadPeerMsg: event 0x4D cr 0x8001 callid 0x0

This may be due to the wrong ISDN switch type at one of the ends

You are set to use

interface Serial0/0/1:15

isdn switch-type primary-net5

Are you sure this is what the Right FAX is set to ?

Regards,
Alex.
Please rate useful posts.

Regards, Alex. Please rate useful posts.
0 Helpful
Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:

Customers Also Viewed These Support Documents