Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

Routing between DP

Afternoon guys!! Im having a nightmare at the moment trying to get a number i dial "1090" to be routed to a gateway, once at the gateway for it then to be translated into another number "2649" for this to be matched under a DP and sent back to the call manager. sounds simple but is giving me a mah00sive headache, the reason for me doing this, is to drop the call a PLAR one into our call centre queues. which when routing in between the partitions in CCM our CS solution doesnt like an therefore doesnt drop to our agents.

The config is below would be nice if anyone has a solution or another perspective on where im going wrong.

voice translation-rule 1090

rule 1 /1090/ /2639/

voice trainslation-profile Outbound_test

translate called 1090

Dial-peer voice 1090 voip

translation-profile incoming 1090

destination-pattern ....

progress_ind setup enable 3

no modem passthrough

voice-class codec 1000

voice-class h323 1

session target dns:etg-ccm02

incomfing called-number .

detmf-relay h245-alphanumeric

fax-relay ecm diable

ip qos dscp cs3 signalling

no vad

incoming called-number 1090

below is the debug of the DP:

*Jun 25 10:47:50.010: //-1/00B4A0362008/DPM/dpAssociateIncomingPeerCore:

Calling Number=3413, Called Number=1090, Voice-Interface=0x0,

Timeout=TRUE, Peer Encap Type=ENCAP_VOIP, Peer Search Type=PEER_TYPE_VOICE,

Peer Info Type=DIALPEER_INFO_SPEECH

*Jun 25 10:47:50.010: //-1/00B4A0362008/DPM/dpAssociateIncomingPeerCore:

Result=Success(0) after DP_MATCH_INCOMING_DNIS; Incoming Dial-peer=1090

*Jun 25 10:47:50.014: //-1/00B4A0362008/DPM/dpAssociateIncomingPeerCore:

Calling Number=3413, Called Number=1090, Voice-Interface=0x0,

Timeout=TRUE, Peer Encap Type=ENCAP_VOIP, Peer Search Type=PEER_TYPE_VOICE,

Peer Info Type=DIALPEER_INFO_SPEECH

DR-VGW(config-dial-peer)#

*Jun 25 10:47:50.014: //-1/00B4A0362008/DPM/dpAssociateIncomingPeerCore:

Result=Success(0) after DP_MATCH_INCOMING_DNIS; Incoming Dial-peer=1090

*Jun 25 10:47:50.014: //-1/00B4A0362008/DPM/dpMatchPeersCore:

Calling Number=, Called Number=1090, Peer Info Type=DIALPEER_INFO_SPEECH

*Jun 25 10:47:50.018: //-1/00B4A0362008/DPM/dpMatchPeersCore:

Match Rule=DP_MATCH_DEST; Called Number=1090

*Jun 25 10:47:50.018: //-1/00B4A0362008/DPM/dpMatchPeersCore:

No Outgoing Dial-peer Is Matched; Result=NO_MATCH(-1)

*Jun 25 10:47:50.018: //-1/00B4A0362008/DPM/dpMatchPeersMoreArg:

Result=NO_MATCH(-1)

2 REPLIES
New Member

Re: Routing between DP

Hello,

you're dp are quite mixed. Separe outbound from inbound.

Also noticed that if you have an voip incoming leg et an voip outbound leg, it can only work with ip to ip gw with something like this :

voice service voip

allow-connections h323 to h323

New Member

Re: Routing between DP

Thanks for your response, I already had the allow-connections done actually, just didnt have a outbound Dp configured to route the call after it had been received inbound ~:)

87
Views
0
Helpful
2
Replies
CreatePlease login to create content