Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

Send fxs calls to voicemail in case of no answer or busy tone

Hi Pros,

Can I set how many time a phone connected to a fxs has to ring?

I am trying to forward this number to a voicemail server. Eventhough I have a dial-peer to forward the call,but the FXS keeps ring.

For example, I want to forward the call to voicemail after 5 rings.

1. Have the remote router which the fxs card. Set the number on the port and a Dial-peer to send the call to the voice gw.

2. Voice gateway with 2 dial-peer with different preference number.First dial-peer send call to the remote router(lower preference number).Second dial-peer with higher pref number send the calls to the voicemail server.

My questions: How can I instruct the fxs card to send the call to voicemail?

There are the dial-peers

1.voice gw

a)

dial-peer voice 2013 voip

preference 1

destination-pattern 6046779391

session target ipv4:x.x.x(remote ID)

dtmf-relay h245-signal

ip qos dscp cs5 media

no vad

!

b)

dial-peer voice 20131 voip

preference 2

destination-pattern 6046779391

progress_ind setup enable 3

translate-outgoing calling 12

no translate-outgoing called 11

voice-class codec 2

session protocol sipv2

session target ipv4:x.x(voice server IP)

dtmf-relay rtp-nte

playout-delay nominal 250

playout-delay mode fixed

ip qos dscp cs5 media

no vad

Remote router dial-peer

dial-peer voice 700 voip

preference 9

destination-pattern 6046779391

translate-outgoing calling 2

translate-outgoing called 2

session target ipv4:x(Voice gw IP)

dtmf-relay cisco-rtp

ip qos dscp cs5 media

no vad

!

dial-peer voice 304 pots

max-conn 1

destination-pattern 604677

port 0/2/0

!

Hope i have enough info,

Thanks in advance,

Crazy

6 REPLIES
Hall of Fame Super Gold

Re: Send fxs calls to voicemail in case of no answer or busy ton

For this, configure CME and FXS port in SCCP mode. You will have an ephone-dn on which confgure call-forward.

New Member

Re: Send fxs calls to voicemail in case of no answer or busy ton

There is no ccm involve, it is just a PRI and remote with a fxs port.

Thanks

Hall of Fame Super Gold

Re: Send fxs calls to voicemail in case of no answer or busy ton

CME is not CCM.

CME is something you configure on the remote and let you have the call-forwarding that you require. It is not possible to do it without, exception perhaps a custom TCL/IVR script.

New Member

Re: Send fxs calls to voicemail in case of no answer or busy ton

Sorry, I bet!Is there a way that i can make this simple, just by configure a max ring in the PRI dial-peer?

Crazy

Hall of Fame Super Gold

Re: Send fxs calls to voicemail in case of no answer or busy ton

You can bet as you like, there is no call-forward capability in standard dial-peers.

New Member

Re: Send fxs calls to voicemail in case of no answer or busy ton

This issue has been solved, I just needed to set timeouts rings 30 in the remote fxs ports and set max-connect to 1 in the first dial-peer in the GW side.

Thank you all for your help, I really appreciate it.

Crazy

248
Views
0
Helpful
6
Replies