Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Community Member

Sending different voice calls to two different e1 channels? how?

What I want to do is, when I call 1111 I want to send these calls from the first ten channel;

when I want to call 9999 I want it to use the channels from 10 to 30. Does it possible? Two dial peer

sends voice traffics from different e1 channels... How can this be implemented?

thx

Serial0/1/0:0 unassigned YES unset down down

Serial0/1/0:1 unassigned YES unset down down

Serial0/1/0:2 unassigned YES unset down down

Serial0/1/0:3 unassigned YES unset down down

Serial0/1/0:4 unassigned YES unset down down

Serial0/1/0:5 unassigned YES unset down down

Serial0/1/0:6 unassigned YES unset down down

Serial0/1/0:7 unassigned YES unset down down

Serial0/1/0:8 unassigned YES unset down down

Serial0/1/0:9 unassigned YES unset down down

Serial0/1/0:10 unassigned YES unset down down

Serial0/1/0:11 unassigned YES unset down down

Serial0/1/0:12 unassigned YES unset down down

Serial0/1/0:13 unassigned YES unset down down

Serial0/1/0:14 unassigned YES unset down down

Serial0/1/0:15 unassigned YES NVRAM up up

Serial0/1/0:16 unassigned YES unset down down

Serial0/1/0:17 unassigned YES unset down down

Serial0/1/0:18 unassigned YES unset down down

Serial0/1/0:19 unassigned YES unset down down

Serial0/1/0:20 unassigned YES unset down down

Serial0/1/0:21 unassigned YES unset down down

Serial0/1/0:22 unassigned YES unset down down

Serial0/1/0:23 unassigned YES unset down down

Serial0/1/0:24 unassigned YES unset down down

Serial0/1/0:25 unassigned YES unset down down

Serial0/1/0:26 unassigned YES unset down down

Serial0/1/0:27 unassigned YES unset down down

Serial0/1/0:28 unassigned YES unset down down

Serial0/1/0:29 unassigned YES unset down down

Serial0/1/0:30 unassigned YES unset down down

!

controller E1 0/1/0

pri-group timeslots 1-31

!

interface Serial0/1/0:15

no ip address

no ip proxy-arp

isdn switch-type primary-net5

isdn protocol-emulate network

isdn incoming-voice voice

no cdp enable

dial-peer voice 100 pots

destination-pattern 1111

port 0/1/0:15

dial-peer voice 101 pots

destination-pattern 9999

port 0/1/0:15

1 ACCEPTED SOLUTION

Accepted Solutions
Hall of Fame Super Gold

Re: Sending different voice calls to two different e1 channels?

Trunk-group under controller listing the TS and reference the TG instead of port under DP.

Hope this helps, please rate pos if it does!

6 REPLIES
Hall of Fame Super Gold

Re: Sending different voice calls to two different e1 channels?

Before entering the details of how it can be done, can you tell us why do you want to do this and what problem are you trying to solve ?

Community Member

Re: Sending different voice calls to two different e1 channels?

The other site wants this to route the calls to outside and inside. He says you must do that for his routing. thx

Hall of Fame Super Gold

Re: Sending different voice calls to two different e1 channels?

Can you confirm with them that they need to route based on the channel number rather than called number on a PRI circuit? That is rather unusual in telecom.

However it is possible to configure trunk-group ranging B-channels on a single pri controller.

So I recommend you try to have them do a regular number-based routing before exploring this other route.

Community Member

Re: Sending different voice calls to two different e1 channels?

Actually they are giving access levels to these channels thats why they need this. So when I call 1111 it should go from the first ten channel. Do you have any config for that situation ?

thx

Hall of Fame Super Gold

Re: Sending different voice calls to two different e1 channels?

Trunk-group under controller listing the TS and reference the TG instead of port under DP.

Hope this helps, please rate pos if it does!

Community Member

Re: Sending different voice calls to two different e1 channels?

thx it seems that it works :)

160
Views
0
Helpful
6
Replies
CreatePlease to create content