06-30-2014 08:31 PM - edited 03-16-2019 11:15 PM
I am unable to receive calls to my IP phones when I dial my DIDs. I can make calls out just fine, just not sure why I can't call in. To test I use my cell phone to place a call to my DID (provided my flowroute) and I just get a disconnect tone a few seconds later.
Attached is my current config (FYI I'm new to VOIP and this is a home setup, so any modes that need to be made won't effect anything important)
Cisco 2821 / C2800NM-ADVENTERPRISEK9-M), Version 15.1(4)M8
CME 8.0
Cisco 7975
Flowroute SIP provider
Thank in advance for the help
Solved! Go to Solution.
07-02-2014 10:44 AM
Can you help me with background too:
CME#dir
Directory of flash:/Desktops/320x216x16/
155 -rw- 184 Jul 2 2014 12:18:30 -05:00 List.xml
49 -rw- 571118 Jul 2 2014 05:51:50 -05:00 7975G-Wallpaper.png
50 -rw- 53964 Jul 2 2014 05:56:04 -05:00 7975G-Wallpaper-Thumb.png
________________________________________________________________
tftp-server flash:/Desktops/320x216x16/7975G-Wallpaper.png
tftp-server flash:/Desktops/320x216x16/7975G-Wallpaper-Thumb.png
tftp-server flash:/Desktops/320x216x16/LIST.xml alias Desktops/320x216x16/List.xml
______________________________________________________________
Jul 2 17:20:27.988: TFTP: Looking for Desktops/320x216x16/List.xml
Jul 2 17:20:31.980: TFTP: Looking for Desktops/320x216x16/List.xml
Jul 2 17:20:35.980: TFTP: Looking for Desktops/320x216x16/List.xml
Jul 2 17:20:39.980: TFTP: Looking for Desktops/320x216x16/List.xml
From what I understand, I have everything configured correctly, but my 7975G isn't loading the xml file... Any ideas.
07-02-2014 10:58 AM
Hi,
It looks like there is a difference in the List.xml
In the below you have entered list in CAPITAL:
tftp-server flash:/Desktops/320x216x16/LIST.xml alias Desktops/320x216x16/List.xml
Kindly change it to list.xml and try again
Thanks
DJ
**Please rate useful posts.
07-02-2014 07:13 AM
07-02-2014 07:11 AM
It messed up the dial-peers configuration, please take a deep breath and have a little walk and then remove other dial peer (10,11 & 12) make sure dial-peer looks like below and then dial 9137129524, currently call is hitting to dial-peer 0 (because there is no dial-peer ocnfigured to receive 19137129524) and again it trying to go out using dial-peer 1..
dial-peer voice 1 voip
translation-profile outgoing addlocal
destination-pattern 1[2-9]..[2-9]......T
no modem passthrough
session protocol sipv2
session target dns:sip.flowroute.com
incoming called-number .
translation-profile incoming GRP_1001_1002
dtmf-relay rtp-nte
no vad
Suresh
07-02-2014 07:23 AM
07-02-2014 07:29 AM
Good to know that, add below translation rules under "voice translation-rule 12" and then check..
rule 4 /^17852465184/ /2000/ rule 5 /17852465184/ /2000/
Suresh
07-02-2014 07:34 AM
You rock!!! That rang through too. Couple of tweeks...
7852465184 I would like only to ring 1002
And is there a way to have the caller ID drop the +1 and only show the 9 digit phone number?
Do I need to clean anything up out of my config, is there any that is in there that needs to be removed?
07-02-2014 07:39 AM
Try this for ringing only on 1002.
voice translation-rule 12
rule 1 /^19137129524/ /2000/
rule 2 /19137129524/ /2000/
rule 3 /9137129524/ /2000/
no rule 4 /^17852465184/ /2000/
no rule 5 /17852465184/ /2000/
rule 4 /^17852465184/ /1002/
rule 5 /17852465184/ /1002/
rule 6 /7852465184/ /1002/
07-02-2014 07:55 AM
That did it...
When I dial out, will 1002 show that 785 # and 1001 show 913?
Later on when I add more phones, do I simply just modify the voice-translation rule to point to the extension I want? For example:
voice hunt-group 1 parallel
list 1001,1002,1003 <---- 1003 being future line
pilot 2000
voice translation-rule 12
rule 1 /^19137129524/ /2000/
rule 2 /19137129524/ /2000/
rule 3 /9137129524/ /2000/
rule 4 /^17852465184/ /1002/
rule 5 /17852465184/ /1002/
rule 6 /7852465184/ /1002/
07-02-2014 08:32 AM
Hi,
Yes that is correct.
Instead if you want all the calls to ring a particular number for instance 2000 which is the pilot for the hunt-group.
you can just use a single translation-pattern
rule 1 /^.*/ /2000/
Which means any number will be matched and will be converted to 2000, which will be the pilot of voice hunt group.
07-02-2014 07:52 AM
ephone-dn 1 number 1001 label Home name Home ! ! ephone-dn 2 number 1002 label Office name Office ! ! ephone 1 device-security-mode none description Home Line mac-address C062.6B62.143A button 1:1 ! ! ! ephone 2 device-security-mode none description Office mac-address E8BA.70FB.36E2 button 1:1 bold replace by 2 !
07-02-2014 07:59 AM
I noticed that, made the correction. Thanks
07-02-2014 07:54 AM
You can put below command as "GRP_1002 & PROVIDER_in" profiles are not associated anywhere.
no voice translation-rule 10
no voice translation-profile GRP_1002
no voice translation-profile PROVIDER_in
As per logs, calling number and called number are +17024011492 & 19137129524 respectively for internal call to CME.What caller ID you are getting on Cisco phone and what you want ? I am asking this because you said 9 digits but there are 10 digits number if we exclude 1.
Suresh
Suresh
07-02-2014 07:57 AM
When I call from my cell I see the +1702401XXXX, I want the +1 dropped and only show the 702401XXX
07-02-2014 07:57 AM
to have the caller ID drop the +1 and only show the 9 digit phone number?
as I told you need
for incoming calling number
1. incoming translation rule
2. incoming traslation profile
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: