Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

SIP Trunk CallManger

I team I am trying to configuring a SIP account for SIP provider on a callmanager ver 6.DOes any body have any experience:

My scenary

Cisco IP-Phone (SCCP) ---> CuCM6.0(H.323) ---> Cisco Router 3825 (12.4) ---> SIP-Trunk to SIP-Provider

I configure the sip-ua on Cisco Router ( Voice Gateway )and its regist OK with the provider.

I add an Route patern on the CCM and a dial-peer on the Gateway, but I am not able to finalize the call

1 ACCEPTED SOLUTION

Accepted Solutions
Green

Re: SIP Trunk CallManger

we dont support SIP account registration in cucm.

If you already did that in router itself,

make sure you are pointing to correct ip address, proper sip binding is configured in router, also incoming and outgoing dial-peers are configured.

which calls r failing? incoming or outgoing?

11 REPLIES
Green

Re: SIP Trunk CallManger

we dont support SIP account registration in cucm.

If you already did that in router itself,

make sure you are pointing to correct ip address, proper sip binding is configured in router, also incoming and outgoing dial-peers are configured.

which calls r failing? incoming or outgoing?

New Member

Re: SIP Trunk CallManger

By now I am just testing the outgoing calls

See in attch a sip call details and the dial-peer configuration

Brgds

New Member

Re: SIP Trunk CallManger

By now I am just testing the outgoing calls

See in attch a sip call details and the dial-peer configuration

Brgds

Re: SIP Trunk CallManger

first make sure u have the follwoing commands in ur gateway

voice service voip

allow-connections h323 to h323

allow-connections h323 to sip

allow-connections sip to h323

allow-connections sip to sip

sip

then can you add the following commands to your dial-peer i mean the one you attached and let me know if t works or not

answer-address .T

incoming called-number .

also make sure there is no other dial-peers match the number you dial in your sip dialpeer becuase i have seen you have preference as 1

if did not work after the above changes do the following to ur dial-peer

ial-peer voice 444 voip

description SIP CALL

translation-profile outgoing SIPCALLCENTRIC

preference 0

destination-pattern 901T

answer-address .T

incoming called-number .

codec g711ulaw

voice-class sip url sip

session protocol sipv2

session target dns:callcentric.com

no vad

u may need to add dtmf for future use but this has not effect to call in or out

dtmf-relay rtp-nte

good luck

New Member

Re: SIP Trunk CallManger

Hi just add ( answer-address .T

incoming called-number . ) and ist working fine from Phone on the CCME but its stil not working from ext on CCM

New Member

Re: SIP Trunk CallManger

Hi Team

ANy body have any idea?

New Member

Re: SIP Trunk CallManger

Hi Team

Problem solved

I create a special SIP Profile and a SIP trunk . I add a route patern using this SIP trunk

Thanks to all

New Member

Re: SIP Trunk CallManger

Hello,

Please, can you post the configuration of your gateway ?

New Member

Re: SIP Trunk CallManger

Hello,

Please, can you post the configuration of your gateway ?

New Member

Re: SIP Trunk CallManger

Hi Driss

See in attac , my dial-peer and some rule

In my case in add a especial SIP trunk in call manager

Any other question please let me now

If you want this is my msn

antoniofragoso@hotmail.com

New Member

Re: SIP Trunk CallManger

Thanks Afragoso.

233
Views
10
Helpful
11
Replies