Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

SRST outbound calling

I am trying to get SRST working.  So far inbound calling works fine but I cannot get any outbound calls to work out the PRI.  Hear is a sample of my dial peers:

dial-peer voice 20 pots
destination-pattern 9[2-9]......
port 0/0/0:23
forward-digits 7
!
dial-peer voice 21 pots
destination-pattern 91[2-9]..[2-9]......
port 0/0/0:23
forward-digits 11

Everyone's tags (4)
6 REPLIES
Cisco Employee

Re: SRST outbound calling

Need little more info to advise...

Is this a MGCP or H323/SIP GW?

Since incoming calls are working, I am assuming

phones are registering fine and PRI L3 is active.

Are u able to share your config and maybe capture

following for one failed outbound call?

deb isdn q931

deb voip ccapi inout

Pl. specify calling/called num.

New Member

Re: SRST outbound calling

Here is the full config

voice translation-rule 1
rule 1 /^86535297\(..\)$/ /76\1/
rule 2 /^865682....$/ /917172708412/
rule 3 /^86534344..$/ /917172708412/
rule 4 /^8653454442$/ /917179710027/

voice translation-rule 2

rule 1 // /86535297/

voice translation-profile toBUFforSRST
translate called 1

voice translation-profile ADD_AREA_OUT

translate calling 2

voice-port 0/0/0:23

translation-profile outgoing ADD_AREA_OUT

dial-peer voice 20 pots
destination-pattern 9[2-9]......
port 0/0/0:23
forward-digits 7
!
dial-peer voice 21 pots
destination-pattern 91[2-9]..[2-9]......
port 0/0/0:23
forward-digits 11
!
dial-peer voice 911 pots
destination-pattern 911
port 0/0/0:23
forward-digits 3
!
dial-peer voice 9911 pots
destination-pattern 9911
port 0/0/0:23
forward-digits 3
!
dial-peer voice 1 pots
translation-profile incoming toBUFforSRST
incoming called-number .
direct-inward-dial
port 0/0/0:23
!
dial-peer voice 10 pots
destination-pattern 4...
port 0/0/0:23
forward-digits all
prefix 91717961
!
d


call-manager-fallback
secondary-dialtone 9
max-conferences 8 gain -6
transfer-system full-consult
timeouts interdigit 5
timeouts busy 30
timeouts ringing 60
ip source-address 172.25.15.254 port 2000
max-ephones 25
max-dn 100 dual-line
system message primary Your System is Jacked
system message secondary FallBack

Cisco Employee

Re: SRST outbound calling

Hi Mike,

Pl. get me some meat to work with :-)

Can u provide the debugs I mentioned?

DK

New Member

Re: SRST outbound calling

Unfortuanety the office is open now and I can put them into SRTS mode to do further debugging at this time.  Does the config look right for the most part?

Cisco Employee

Re: SRST outbound calling

yeah, that looks ok...need to see what is happening when

making an outbound call during SRST where those debugs

will come in handy...

Re: SRST outbound calling

One thing to check also is some providers wont accept a call unless the caller ID being sent is part of the DID block on the PRI. During SRST I dont believe outbound caller ID works, it only sends the 4 digits (or however many digits the extension contains) out to the provider. If this is the case you may need some translation profiles defined for outbound caller ID and apply that profile to the outbound dial-peers.

1663
Views
0
Helpful
6
Replies