Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

T1/PRI

Hi,

I am trying to implement T1/PRI using my 2611xm router connected to MC3800 as PBX.

my problem is that there is no ds0-group in the controller T1 0/1, my ios ver is C2600-SPSERVICESK9-M), Version 12.4(17)

and i had VWIC2-2MFT-T1/E1 installed on the router.

regards

1 ACCEPTED SOLUTION

Accepted Solutions
Cisco Employee

Re: T1/PRI

You don't have any DSP's to support the T1 interface. The voice card in slot 1 can only be used with the analogue voice ports installed locally on the network module.

To make the T1 work, you will need an AIM-VOICE-30 module that clips onto the motherboard socket of the router -

http://www.cisco.com/en/US/products/hw/modules/ps2641/products_data_sheet09186a0080088753.html

If you get one, don't forget to add these commands to make it work properly -

network-clock-participate aim 0

network-clock-select 1 t1 0/1

8 REPLIES
New Member

Re: T1/PRI

Try "pri-group ?" rather than "ds0-group ?"

New Member

Re: T1/PRI

Thanks for your response,

pri-group also is not showing, only channel-group and tdm-group.

Regards

Cisco Employee

Re: T1/PRI

do you have DSPs to use that card???

HTH

javalenc

if this helps, please rate

HTH

java

if this helps, please rate

www.cisco.com/go/pdi
New Member

Re: T1/PRI

how to know that ??

Cisco Employee

Re: T1/PRI

do a sh diag

HTH

javalenc

if this helps, please rate

HTH

java

if this helps, please rate

www.cisco.com/go/pdi
New Member

Re: T1/PRI

mgcp-gw#sh diag

WIC Slot 1:

VWIC2-2MFT-T1/E1 - 2-Port RJ-48 Multiflex Trunk - T1/E1

Hardware Revision : 0.0

Top Assy. Part Number : 800-22629-05

Board Revision : B0

Deviation Number : 0

Fab Version : 04

PCB Serial Number : FOC1147691L

RMA Test History : 00

RMA Number : 0-0-0-0

RMA History : 00

Product (FRU) Number : VWIC2-2MFT-T1/E1

Version Identifier : V01

EEPROM format version 4

EEPROM contents (hex):

0x00: 04 FF 40 03 FC 41 00 00 C0 46 03 20 00 58 65 05

0x10: 42 42 30 88 00 00 00 00 02 04 C1 8B 46 4F 43 31

0x20: 31 34 37 36 39 31 4C 03 00 81 00 00 00 00 04 00

0x30: CB 90 56 57 49 43 32 2D 32 4D 46 54 2D 54 31 2F

0x40: 45 31 89 56 30 31 20 D9 02 40 C1 FF FF FF FF FF

0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

New Member

Re: T1/PRI

here is my sh diag and sh ver

Cisco Employee

Re: T1/PRI

You don't have any DSP's to support the T1 interface. The voice card in slot 1 can only be used with the analogue voice ports installed locally on the network module.

To make the T1 work, you will need an AIM-VOICE-30 module that clips onto the motherboard socket of the router -

http://www.cisco.com/en/US/products/hw/modules/ps2641/products_data_sheet09186a0080088753.html

If you get one, don't forget to add these commands to make it work properly -

network-clock-participate aim 0

network-clock-select 1 t1 0/1

160
Views
0
Helpful
8
Replies