Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
New Member

Time zone

Hello,

I have changed the time zone but all my IP Phone always the old time.

I want to modify the time and put a specific time for all my IP Phone, how to do?

Regards

1 ACCEPTED SOLUTION

Accepted Solutions
Hall of Fame Super Red

Re: Time zone

Hi Pascal,

This is not an uncommon issue that should be quite fixable :)

Troubleshooting Incorrect Time Stamp on IP Phones in Cisco Unified CME

http://www.cisco.com/en/US/docs/voice_ip_comm/cucme/troubleshooting/guide/ts_time.html#wp1053981

After changing the time-zone setting you could follow these steps.

Usage Guidelines

This command works with the vendorConfig section of the Sep*.conf.xml configuration file, which is read by the phone firmware when the Cisco IP Phone is booted up. Certain phones, such as the Cisco Unified IP Phone 7906 , 7911, 7931, 7941, 7942, 7945, 7961, 7962, 7965, 7970 , 7971, and 7975, obtain Coordinated Universal Time (UTC) from the clock of the Cisco router. To display the correct local time, the time display on these phones must be offset by using this command.

This command is not required for Cisco Unified IP Phone 7902G, 7905G, 7912G, 7920, 7921, 7935, 7936, 7940, 7960, or 7985G.

For changes to the time-zone settings take effect, the Sep*.conf.xml file must be updated by using the create cnf-files command and the Cisco IP phones must rebooted by using the reset command.

http://www.cisco.com/en/US/docs/voice_ip_comm/cucme/command/reference/cme_t1ht.html#wp1023398

under the telephony-service -

no create cnf-files

create cnf-files

Then reboot the individual phones :)

This was really covered nicely by Paul in this thread :)

http://forum.cisco.com/eforum/servlet/NetProf?page=netprof&forum=Unified%20Communications%20and%20Video&topic=General&CommCmd=MB%3Fcmd%3Ddisplay_location%26location%3D.2cbf1665/0

Hope this helps!

Rob

6 REPLIES
New Member

Re: Time zone

Did you reset you phones ?

New Member

Re: Time zone

yes

New Member

Re: Time zone

Please provide sreenshots with configutations.

New Member

Re: Time zone

I have just put time-zone 21 on the service-telephony.

I don't know if I must to use the time-zone command to change time.

I want to change the time on the all IP Phone.

Regards

Hall of Fame Super Red

Re: Time zone

Hi Pascal,

This is not an uncommon issue that should be quite fixable :)

Troubleshooting Incorrect Time Stamp on IP Phones in Cisco Unified CME

http://www.cisco.com/en/US/docs/voice_ip_comm/cucme/troubleshooting/guide/ts_time.html#wp1053981

After changing the time-zone setting you could follow these steps.

Usage Guidelines

This command works with the vendorConfig section of the Sep*.conf.xml configuration file, which is read by the phone firmware when the Cisco IP Phone is booted up. Certain phones, such as the Cisco Unified IP Phone 7906 , 7911, 7931, 7941, 7942, 7945, 7961, 7962, 7965, 7970 , 7971, and 7975, obtain Coordinated Universal Time (UTC) from the clock of the Cisco router. To display the correct local time, the time display on these phones must be offset by using this command.

This command is not required for Cisco Unified IP Phone 7902G, 7905G, 7912G, 7920, 7921, 7935, 7936, 7940, 7960, or 7985G.

For changes to the time-zone settings take effect, the Sep*.conf.xml file must be updated by using the create cnf-files command and the Cisco IP phones must rebooted by using the reset command.

http://www.cisco.com/en/US/docs/voice_ip_comm/cucme/command/reference/cme_t1ht.html#wp1023398

under the telephony-service -

no create cnf-files

create cnf-files

Then reboot the individual phones :)

This was really covered nicely by Paul in this thread :)

http://forum.cisco.com/eforum/servlet/NetProf?page=netprof&forum=Unified%20Communications%20and%20Video&topic=General&CommCmd=MB%3Fcmd%3Ddisplay_location%26location%3D.2cbf1665/0

Hope this helps!

Rob

New Member

Re: Time zone

Thank you Rob.

344
Views
0
Helpful
6
Replies
CreatePlease to create content