Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

Transfer analog phone to IP Phone

Hello,

I have a problem to transfer a call to analog phone from an IP Phone. On IP Phone, I can dial only two digit and after hook.

On analog phone, how to enable the transfer key? It's possible to use the "R" key on the phone keyboard?

There no problem of transfer ip phone to ip phone.

Regards

14 REPLIES
New Member

Re: Transfer analog phone to IP Phone

I have add this command, but now the transfer is permit between anlog phone and IP Phone but transfer is not immediate, I must wait 5seconds or more. There are a solution for transfer immediate without time?

How to enable the transfer on analog phone?

CallManager(config-telephony)#transfer-pattern .T

CallManager(config-telephony)#call-forward pattern .T

Bronze

Re: Transfer analog phone to IP Phone

Hi, maybe you could try a specific transfer pattern according to your dial-plan.

CallManager(config-telephony)#transfer-pattern ....

CallManager(config-telephony)#call-forward pattern ....

Or decrease the interdigit timeout (default is 15 sec).

CallManager(config-telephony)#timeout interdigit "value 2 to 120 sec"

Hope this help

David

New Member

Re: Transfer analog phone to IP Phone

I have try that

CallManager(config-telephony)#transfer-pattern 55

CallManager(config-telephony)#call-forward pattern 56

On analog phone I call IP Phone 100 and now I want to transfer the call to the IP Phone 101 but on analog phone if I dial 56 or 55 or other nothing happens

Re: Transfer analog phone to IP Phone

You would need tranfer-pattern 10.

Re: Transfer analog phone to IP Phone

If you want supplementary features for analog phones (such as transfers), you should make this a SCCP controlled FXS port.

Here's the configuration guide:

http://www.cisco.com/en/US/docs/ios/voice/fxs/configuration/guide/fxssccpsplmft.html

hth,

nick

New Member

Re: Transfer analog phone to IP Phone

Sorry, I don't understand.

When you are on an anolog phone how to transfer a call to an another extension?

Re: Transfer analog phone to IP Phone

That is in the document that I sent. You have to register that port with SCCP, and then you have to set up feature codes where you dial *2 and then the number, and things like that.

It's quite a bit of configuration. I suggest reading through the links I sent.

New Member

Re: Transfer analog phone to IP Phone

I have put

Router(config)#stcapp feature access-code

Router#sh stcapp feature codes

stcapp feature access-code

prefix **

call forward all **1

call forward cancel **2

pickup local group **3

pickup different group **4

pickup direct **6

stcapp feature speed-dial disabled

Maybe I have forgot something? But when I dial **1 to tranfer a call nothing it happens.

Regards

Re: Transfer analog phone to IP Phone

Yes, you need the entire sccp configuration.

It will look like:

sccp

sccp ccm group 1

ass ccm 1 pri 1

....

New Member

Re: Transfer analog phone to IP Phone

I have always the same problem, I want to transfer a call from my analog phone but when I dial feature access-code key on my analog keyboad nothing it happens,maybe I have do somting wrong?

See my conf

My FXS phone is on port 0/1/0

stcapp ccm-group 1

stcapp

!

stcapp feature access-code

prefix *#

call forward all 2

call forward cancel 9

voice-port 0/1/0

caller-id enable

sccp local GigabitEthernet0/1

sccp ccm 192.168.0.13 identifier 2

sccp ccm 192.168.0.12 identifier 1

sccp

!

sccp ccm group 1

associate ccm 1 priority 1

associate ccm 2 priority 2

dial-peer voice 76 pots

destination-pattern 250

port 0/1/0

dial-peer voice 78 pots

service stcapp

port 0/1/0

New Member

Re: Transfer analog phone to IP Phone

Nobody have an idea?

Re: Transfer analog phone to IP Phone

check 'show sccp' to see if the analog port is registered

New Member

Re: Transfer analog phone to IP Phone

CallManager#sh sccp

SCCP Admin State: UP

Gateway IP Address: 192.168.0.1, Port Number: 2000

IP Precedence: 5

User Masked Codec list: None

Call Manager: 192.168.0.12, Port Number: 2000

Priority: N/A, Version: 3.1, Identifier: 1

Call Manager: 192.168.0.13, Port Number: 2000

Priority: N/A, Version: 3.1, Identifier: 2

Alg_Phone Oper State: ACTIVE_IN_PROGRESS - Cause Code: TCP_CONN_ERROR

Active Call Manager: NONE

TCP Link Status: NOT_CONNECTED, Device Name: AN2255E60821080

Reported Max Streams: 1, Reported Max OOS Streams: 0

Supported Codec: g711ulaw, Maximum Packetization Period: 20

Supported Codec: g711alaw, Maximum Packetization Period: 20

Supported Codec: g729r8, Maximum Packetization Period: 220

Supported Codec: g729ar8, Maximum Packetization Period: 220

Supported Codec: g729br8, Maximum Packetization Period: 220

Supported Codec: g729r8, Maximum Packetization Period: 220

Re: Transfer analog phone to IP Phone

It's not registered. You will need to go back and check your sccp configuration, as well as your CME configuration.

hth,

nick

610
Views
0
Helpful
14
Replies