Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

transfer not allow in CME 4.2

I have just set conference and transcoding in CME but I can not transfer call, even internal.

sccp local GigabitEthernet0/1

sccp ccm 10.10.10.1 identifier 1 version 4.0

sccp

!

sccp ccm group 1

associate ccm 1 priority 1

associate profile 2 register CFB00170eaf1d20

associate profile 1 register MTP00170eaf1d20

dspfarm profile 1 transcode

codec g711ulaw

codec g711alaw

codec g729r8

codec g729ar8

codec g729abr8

maximum sessions 2

associate application SCCP

no shutdown

dspfarm profile 2 conference

codec g711ulaw

codec g711alaw

codec g729r8

codec g729ar8

codec g729abr8

maximum sessions 2

associate application SCCP

no shutdown

telephony-service

sdspfarm units 5

sdspfarm transcode sessions 2

sdspfarm tag 1 MTP00170eaf1d20

sdspfarm tag 2 CFB00170eaf1d20

***********************************

CME#show dspfarm all

Dspfarm Profile Configuration

Profile ID = 1, Service = TRANSCODING, Resource ID = 1

Profile Description :

Profile Service Mode : Non Secure

Profile Admin State : UP

Profile Operation State : ACTIVE

Application : SCCP Status : ASSOCIATED

Resource Provider : FLEX_DSPRM Status : UP

Number of Resource Configured : 2

Number of Resource Available : 2

Codec Configuration

Codec : g711ulaw, Maximum Packetization Period : 30

Codec : g711alaw, Maximum Packetization Period : 30

Codec : ilbc, Maximum Packetization Period : 60

Codec : g723r63, Maximum Packetization Period : 60

Codec : g723r53, Maximum Packetization Period : 60

Codec : gsmamr-nb, Maximum Packetization Period : 60

Codec : g729ar8, Maximum Packetization Period : 60

Codec : g729abr8, Maximum Packetization Period : 60

Codec : g729r8, Maximum Packetization Period : 60

Dspfarm Profile Configuration

Profile ID = 2, Service = CONFERENCING, Resource ID = 2

Profile Description :

Profile Service Mode : Non Secure

Profile Admin State : UP

Profile Operation State : ACTIVE

Application : SCCP Status : ASSOCIATED

Resource Provider : FLEX_DSPRM Status : UP

Number of Resource Configured : 2

Number of Resource Available : 2

Codec Configuration

Codec : g711ulaw, Maximum Packetization Period : 30 , Transcoder: Not Required

Codec : g711alaw, Maximum Packetization Period : 30 , Transcoder: Not Required

Codec : g729ar8, Maximum Packetization Period : 60 , Transcoder: Not Required

Codec : g729abr8, Maximum Packetization Period : 60 , Transcoder: Not Required

Codec : g729r8, Maximum Packetization Period : 60 , Transcoder: Not Required

Codec : g729br8, Maximum Packetization Period : 60 , Transcoder: Not Required

SLOT DSP VERSION STATUS CHNL USE TYPE RSC_ID BRIDGE_ID PKTS_TXED PKTS_RXED

0 1 21.4.0 UP N/A FREE xcode 1 - - -

0 1 21.4.0 UP N/A FREE xcode 1 - - -

0 12 1.1.137 UP N/A FREE conf 2 - - -

0 12 1.1.137 UP N/A FREE conf 2 - - -

Total number of DSPFARM DSP channel(s) 4

1 ACCEPTED SOLUTION

Accepted Solutions
Hall of Fame Super Silver

Re: transfer not allow in CME 4.2

conferecning and transcoding has nothing to do with transfers (unless you need transcoded calls). Make sure you have the following command under telephony-service

transfer-pattern .T

or somthing similar.

HTH,

Chris

2 REPLIES
Hall of Fame Super Silver

Re: transfer not allow in CME 4.2

conferecning and transcoding has nothing to do with transfers (unless you need transcoded calls). Make sure you have the following command under telephony-service

transfer-pattern .T

or somthing similar.

HTH,

Chris

New Member

Re: transfer not allow in CME 4.2

Hi Chris,

Your right, I forgot that command

now it work the tranfers

thanks for your time

regards

108
Views
0
Helpful
2
Replies