Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

UC520 - E1 R2 - Venezuela (MOVISTAR)

Greetings,

i need configure an e1 card on UC520-24U-8FXO-K9, but the info founded to make it is not complete, i don't sure what is wrong

The e1 is up but i can't send or recive calls,and i don't know how associate the trunk pstn trunks.

that is the info suplied by the PSTN company:

Signal: Q.421 (R2)
-Signal IN: MFC-R2 (7 Lines IN)
-Signal Out: DTMF o MFC-R2 (8 Lines Out)

Header: 2514200000


Numbers: from 2514200000  to 2514200099

This is the configuration that places:

!

card type e1 0 2

network-clock-participate wic 2

!

!

trunk group ALL_T1E1
hunt-scheme longest-idle

!

!

controller E1 0/2/0
framing NO-CRC4
ds0-group 0 timeslots 1-15 type r2-digital r2-compelled ani
ds0-group 1 timeslots 17-31 type r2-digital dtmf dnis
cas-custom 0
  country venezuela
  answer-signal group-a 6
  dnis-complete
process-max-time 50

!

!
voice-port 0/2/0:0
!
voice-port 0/2/0:1
!

Thanks in advance by your help.

Everyone's tags (4)
9 REPLIES
Hall of Fame Super Gold

Re: UC520 - E1 R2 - Venezuela (MOVISTAR)

Begin sending "show controllers E1"

New Member

Re: UC520 - E1 R2 - Venezuela (MOVISTAR)

UC520#sh controllers e1
E1 0/2/0 is up.
  Applique type is Channelized E1 - balanced
  No alarms detected.
  alarm-trigger is not set
  Version info Firmware: 20090408, FPGA: 13, spm_count = 0
  Framing is NO-CRC4, Line Code is HDB3, Clock Source is Line.
  Data in current interval (98 seconds elapsed):
     0 Line Code Violations, 0 Path Code Violations
     1 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
     1 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
  Total Data (last 24 hours)
     0 Line Code Violations, 0 Path Code Violations,
     1033 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,
     1033 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
UC520#

Hall of Fame Super Gold

Re: UC520 - E1 R2 - Venezuela (MOVISTAR)

You need "network-clock-select 1 e1 0/2/0"  to eliminate slip.

The you need the dial-peer configuration, do you know what it means ?

I have a VZ movistar site, but not here, can look into it tomorrow.

New Member

Re: UC520 - E1 R2 - Venezuela (MOVISTAR)

I include the "network-clock-select 1 e1 0/2/0"  and avoid the splits, thanks, and i hope compare to your VZ movistar site configuration, thanks again.

I don´t configure the e1 associates dial-peers yet, nor the trounk group all_t1e1, i don't know how for e1 configuration.

that is the dial-peer configuration:

!
dial-peer cor custom
name internal
name local
name local-plus
name international
name national
name national-plus
name emergency
name toll-free
!
!
dial-peer cor list call-internal
member internal
!
dial-peer cor list call-local
member local
!
dial-peer cor list call-local-plus
member local-plus
!
dial-peer cor list call-national
member national
!
dial-peer cor list call-national-plus
member national-plus
!
dial-peer cor list call-international
member international
!
dial-peer cor list call-emergency
member emergency
!
dial-peer cor list call-toll-free
member toll-free
!
dial-peer cor list user-internal
member internal
member emergency
!
dial-peer cor list user-local
member internal
member local
member emergency
member toll-free
!
dial-peer cor list user-local-plus
member internal
member local
member local-plus
member emergency
member toll-free
!
dial-peer cor list user-national
member internal
member local
member local-plus
member national
member emergency
member toll-free
!
dial-peer cor list user-national-plus
member internal
member local
member local-plus
member national
member national-plus
member emergency
member toll-free
!
dial-peer cor list user-international
member internal
member local
member local-plus
member international
member national
member national-plus
member emergency
member toll-free
!
!
dial-peer voice 1 pots
service stcapp
port 0/0/0
!
dial-peer voice 2 pots
service stcapp
port 0/0/1
!
dial-peer voice 3 pots
service stcapp
port 0/0/2
!
dial-peer voice 4 pots
service stcapp
port 0/0/3
!
dial-peer voice 5 pots
description ** MOH Port **
destination-pattern ABC
port 0/4/0
no sip-register
!
dial-peer voice 50 pots
description ** incoming dial peer **
incoming called-number .%
port 0/1/0
!
dial-peer voice 51 pots
description ** incoming dial peer **
incoming called-number .%
port 0/1/1
!
dial-peer voice 52 pots
description ** incoming dial peer **
incoming called-number .%
port 0/1/2
!
dial-peer voice 53 pots
description ** incoming dial peer **
incoming called-number .%
port 0/1/3
!
dial-peer voice 100 pots
description ** incoming dial peer **
incoming called-number .%
!
dial-peer voice 101 pots
description ** incoming dial peer **
incoming called-number .%
!
dial-peer voice 102 pots
description ** incoming dial peer **
incoming called-number .%
!
dial-peer voice 103 pots
description ** incoming dial peer **
incoming called-number .%
!
dial-peer voice 150 pots
description ** incoming dial peer **
incoming called-number .%
port 0/3/0
!
dial-peer voice 151 pots
description ** incoming dial peer **
incoming called-number .%
port 0/3/1
!
dial-peer voice 152 pots
description ** incoming dial peer **
incoming called-number .%
port 0/3/2
!
dial-peer voice 153 pots
description ** incoming dial peer **
incoming called-number .%
port 0/3/3
!
dial-peer voice 2000 voip
description ** cue voicemail pilot number **
destination-pattern 199
b2bua
voice-class sip outbound-proxy  ipv4:10.1.10.1
session protocol sipv2
session target ipv4:10.1.10.1
dtmf-relay sip-notify
codec g711ulaw
no vad
!
dial-peer voice 54 pots
description ** FXO pots dial-peer **
destination-pattern A0
port 0/1/0
no sip-register
!
dial-peer voice 55 pots
description ** FXO pots dial-peer **
destination-pattern A1
port 0/1/1
no sip-register
!
dial-peer voice 56 pots
description ** FXO pots dial-peer **
destination-pattern A2
port 0/1/2
no sip-register
!
dial-peer voice 57 pots
description ** FXO pots dial-peer **
destination-pattern A3
port 0/1/3
no sip-register
!
dial-peer voice 104 pots
description ** FXO pots dial-peer **
destination-pattern A4
no sip-register
!
dial-peer voice 105 pots
description ** FXO pots dial-peer **
destination-pattern A5
no sip-register
!
dial-peer voice 106 pots
description ** FXO pots dial-peer **
destination-pattern A6
no sip-register
!
dial-peer voice 107 pots
description ** FXO pots dial-peer **
destination-pattern A7
no sip-register
!
dial-peer voice 154 pots
description ** FXO pots dial-peer **
destination-pattern A8
port 0/3/0
no sip-register
!
dial-peer voice 155 pots
description ** FXO pots dial-peer **
destination-pattern A9
port 0/3/1
no sip-register
!
dial-peer voice 156 pots
description ** FXO pots dial-peer **
destination-pattern A10
port 0/3/2
no sip-register
!
dial-peer voice 157 pots
description ** FXO pots dial-peer **
destination-pattern A11
port 0/3/3
no sip-register
!
!
no dial-peer outbound status-check pots
!
!

Hall of Fame Super Gold

Re: UC520 - E1 R2 - Venezuela (MOVISTAR)

You do not have DP for the digital ports, and to muich confusing and unnecessary DPs and cor-list.

Recommend you locate a certified partner or reputable consultant to help you.

Sorry, my coworkers with access to VX site have left for the day.

New Member

Re: UC520 - E1 R2 - Venezuela (MOVISTAR)

its because are the the default configuration make it by the CCA interface, i think will be needed showed,

i can't configrue digital DP until associate the trunk-group to voice-ports i think..

do you know another doc or sample to trunk-group, voice-ports and dps digital? that i founded isn't usefully

please let me know whe you find the VE movistar configuration to compare

thks again

Hall of Fame Super Gold

Re: UC520 - E1 R2 - Venezuela (MOVISTAR)

Below what we use for Movistar. I suspect come coammnds are not needed and could have left to defaults.

You don't need trunk-groups for normal use. If you use CCA, you will never get it working. Study the CLI or hire someone qualified.


Please remember to rate useful post clicking on the stars below.

controller E1 0/1/0
framing NO-CRC4
ds0-group 0 timeslots 1-15 type r2-digital dtmf dnis
ds0-group 1 timeslots 17-31 type r2-digital r2-compelled ani
cas-custom 1
   country venezuela
   debounce-time 10
   release-guard-time 10
   reanswer-time 1000
   answer-signal group-a 6
   dnis-digits min 4 max 4
   answer-guard-time 1

New Member

Re: UC520 - E1 R2 - Venezuela (MOVISTAR)

can you show me the DPs for it?

am try by CLI interface right now

thanks again.

Hall of Fame Super Gold

Re: UC520 - E1 R2 - Venezuela (MOVISTAR)

DP are not specific for Movistar.

You really need to study cisco voice configuration, or give the job to someone that knows.

Otherwise you will only get very poor resultaùs, and an angry customer.

1398
Views
10
Helpful
9
Replies