Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

UC520 Inbound Caller ID

Hi All,

We have a UC520 system installed, it works fine in and outbound calls. All outbound calls show our primary number as the CID, however right now incoming calls only show the calling number.

When I added this line to my PRI port:

interface Serial0/3/0:23

no isdn supp-service name calling

incoming caller ID now shows correctly, however now I am unable to make out bound calls.

I think these are all of the rules for outbound but am not sure why.

Below is what I assume are the pieces of configuration needed ?

voice translation-rule 1111

rule 1 /.*/ /xxxxxxxxxx/

voice translation-profile OUTGOING_TRANSLATION_PROFILE

translate calling 1111

voice translation-profile CALLER_ID_TRANSLATION_PROFILE

translate calling 1111

dial-peer voice 151 pots

corlist outgoing call-local

description ** T1 pots dial-peer **

translation-profile outgoing CALLER_ID_TRANSLATION_PROFILE

preference 5

destination-pattern 9[2-9]......

port 0/3/0:23

forward-digits 7

no sip-register

!

dial-peer voice 152 pots

corlist outgoing call-domestic

description ** T1 pots dial-peer **

translation-profile outgoing CALLER_ID_TRANSLATION_PROFILE

preference 5

destination-pattern 91[2-9]..[2-9]......

port 0/3/0:23

prefix 1

no sip-register

!

dial-peer voice 154 pots

description ** T1 pots dial-peer **-Emergency dial-peer

translation-profile outgoing CALLER_ID_TRANSLATION_PROFILE

preference 5

destination-pattern 9911

port 0/3/0:23

forward-digits 3

no sip-register

!

dial-peer voice 155 pots

description ** T1 pots dial-peer **-Emergency dial-peer

translation-profile outgoing CALLER_ID_TRANSLATION_PROFILE

preference 5

destination-pattern 911

port 0/3/0:23

forward-digits 3

no sip-register

!

dial-peer voice 156 pots

corlist outgoing call-local

description ** T1 pots dial-peer **

translation-profile outgoing CALLER_ID_TRANSLATION_PROFILE

preference 5

destination-pattern 9[2-9]11

port 0/3/0:23

forward-digits 3

no sip-register

Thank You.

Gary

5 REPLIES
Hall of Fame Super Gold

Re: UC520 Inbound Caller ID

Take "debug isdn q931" with "term mon" it the various situations, that will clarify what's going on.

New Member

Re: UC520 Inbound Caller ID

Ok, I get this reject code - guess this is the reason.

268910: Apr 24 01:43:10.264: ISDN Se0/3/0:23 Q931: RX <- RELEASE_COMP pd = 8 callref = 0x820C

Cause i = 0x82B2 - Requested facility not subscribed

Hall of Fame Super Gold

Re: UC520 Inbound Caller ID

Ok, but one should check what exactly is the facility and why the clid is not correct when facility is not used.

New Member

Re: UC520 Inbound Caller ID

Morning,

I have attached the fail log - I tried working my way through it and comparing it against a connection when I don't use the "isdn supp-service name calling" line - wasn't sure what I should be looking for.

Thanks for your help.

Hall of Fame Super Gold

Re: UC520 Inbound Caller ID

Please take the traces with "debug isdn q931" ad indicated above, and nothing else.

515
Views
0
Helpful
5
Replies