Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

Unprocessed CallerID on CME

Hi,

We have a trouble with CallerID. We receive it from the telco, but CallManagerExpress does not process it. Here's the debug log of a test call I made.

ISDN Se0/0/0:23 Q931: RX <- SETUP pd = 8 callref = 0x010D

Bearer Capability i = 0x8090A2

Standard = CCITT

Transfer Capability = Speech

Transfer Mode = Circuit

Transfer Rate = 64 kbit/s

Channel ID i = 0xA98381

Exclusive, Channel 1

Facility i = 0x9F8B0100A11002010102010080084D4F4E415354204A

Progress Ind i = 0x8283 - Origination address is non-ISDN

Calling Party Number i = 0x2183, '450581xxxx'

Plan:ISDN, Type:National

Called Party Number i = 0x80, '2505'

Plan:Unknown, Type:Unknown

013118: Feb 1 20:48:41.921: ISDN Se0/0/0:23 Q931: TX -> CALL_PROC pd = 8 callref = 0x810D

Channel ID i = 0xA98381

Exclusive, Channel 1

ISDN Se0/0/0:23 Q931: TX -> ALERTING pd = 8 callref = 0x810D

ISDN Se0/0/0:23 Q931: TX -> CONNECT pd = 8 callref = 0x810D

ISDN Se0/0/0:23 Q931: RX <- CONNECT_ACK pd = 8 callref = 0x010D

ISDN Se0/0/0:23 **ERROR**: call_progress: DEV_CONNECTED VOICE ERROR: Bearer capability not available(0x3A): b channel 0 call id 0xBA

%ISDN-6-CONNECT: Interface Serial0/0/0:0 is now connected to 450581xxxx N/A

ISDN Se0/0/0:23 Q931: RX <- DISCONNECT pd = 8 callref = 0x010D

Cause i = 0x8090 - Normal call clearing

%ISDN-6-DISCONNECT: Interface Serial0/0/0:0 disconnected from 450581xxxx , call lasted 5 seconds

ISDN Se0/0/0:23 Q931: TX -> RELEASE pd = 8 callref = 0x810D

Feb 1 20:48:47.145: ISDN Se0/0/0:23 Q931: RX <- RELEASE_COMP pd = 8 callref = 0x010D

See...

Facility i = 0x9F8B0100A11002010102010080084D4F4E415354204A

translates into

MONAST J

How can I tell CME to process those messages, and send them to the phones ?

Thank you!

1 ACCEPTED SOLUTION

Accepted Solutions
Hall of Fame Super Gold

Re: Unprocessed CallerID on CME

Ok, I've found your previous message when the IE was not present at all. can you try:

voice service voip

qsig decode

6 REPLIES
Hall of Fame Super Gold

Re: Unprocessed CallerID on CME

Hi, which switchtype have you confgured, and which exact IOS version ?

You should be able to see the name when all is allright.

New Member

Re: Unprocessed CallerID on CME

Cisco IOS Software, 3800 Software (C3845-SPSERVICESK9-M), Version 12.4(11)XJ4, RELEASE SOFTWARE (fc2)

isdn switch-type primary-5ess

As the telco's requirement.

Hall of Fame Super Gold

Re: Unprocessed CallerID on CME

Whoops, I had forgot. Please configure

isdn supp-service name calling

under inteface.

Hope this helps, please rate post if it does!

New Member

Re: Unprocessed CallerID on CME

It's already configured that way.

Hall of Fame Super Gold

Re: Unprocessed CallerID on CME

Ok, I've found your previous message when the IE was not present at all. can you try:

voice service voip

qsig decode

New Member

Re: Unprocessed CallerID on CME

THANK YOU!

It worked !!

155
Views
0
Helpful
6
Replies
CreatePlease to create content