Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

USA Calling UK

Hi,

I have the following setup on my USA Chicago network

CUCM Publisher 7.1.3.20000-2

CUCM Subscriber 7.1.3.20000-2

VG2811 (C2800NM-IPVOICEK9-M), Version 12.4(7d)

Route Pattern: 9.011!#

Calling from Chicago to Australia/Asia/Japan/Middle East via the International Route Pattern works perfectly. When I call UK using the number

9 011 44XXXXXXXXXX# I get a recording "your call cannot be completed as dialed"

My debug q931 below:

000104: Mar 10 2010 23:39:18.419 GMT: ISDN Se0/0/0:23 Q931: TX -> SETUP pd = 8  callref = 0x0084
        Bearer Capability i = 0x8090A2
                Standard = CCITT
                Transfer Capability = Speech 
                Transfer Mode = Circuit
                Transfer Rate = 64 kbit/s
        Channel ID i = 0xA98397
                Exclusive, Channel 23
        Calling Party Number i = 0x2181, '312803XXXX'
                Plan:ISDN, Type:National
        Called Party Number i = 0x91, '01144XXXXXXXXXX'
                Plan:ISDN, Type:International <-- NOTE
000105: Mar 10 2010 23:39:18.503 GMT: ISDN Se0/0/0:23 Q931: RX <- RELEASE_COMP pd = 8  callref = 0x8084
        Cause i = 0x809C - Invalid number format (incomplete number)

The local carrier advises that my device is sending Plan ISDN type "International" to them and will only accept "unknown" call types.

Below is another debug q931 to Australia that connects:

000117: Mar 10 2010 23:41:32.646 GMT: ISDN Se0/0/0:23 Q931: TX -> SETUP pd = 8  callref = 0x0086
        Bearer Capability i = 0x8090A2
                Standard = CCITT
                Transfer Capability = Speech 
                Transfer Mode = Circuit
                Transfer Rate = 64 kbit/s
        Channel ID i = 0xA98397
                Exclusive, Channel 23
        Calling Party Number i = 0x21A1, '312803XXXX'
                Plan:ISDN, Type:National
        Called Party Number i = 0x80, '01161292317417'
                Plan:Unknown, Type:Unknown <-- NOTE
000118: Mar 10 2010 23:41:32.750 GMT: ISDN Se0/0/0:23 Q931: RX <- CALL_PROC pd = 8  callref = 0x8086
        Channel ID i = 0xA98397
                Exclusive, Channel 23
000119: Mar 10 2010 23:41:36.902 GMT: ISDN Se0/0/0:23 Q931: RX <- ALERTING pd = 8  callref = 0x8086
        Progress Ind i = 0x8088 - In-band info or appropriate now available
000120: Mar 10 2010 23:41:37.174 GMT: ISDN Se0/0/0:23 Q931: TX -> DISCONNECT pd = 8  callref = 0x0086
        Cause i = 0x8090 - Normal call clearing
000121: Mar 10 2010 23:41:37.450 GMT: ISDN Se0/0/0:23 Q931: RX <- RELEASE pd = 8  callref = 0x8086
000122: Mar 10 2010 23:41:37.454 GMT: ISDN Se0/0/0:23 Q931: TX -> RELEASE_COMP pd = 8  callref = 0x0086

I have check all settings in CUCM and all set to default or CallManager under Route Pattern and H.323 Gateway.

Help.

Thanks

1 ACCEPTED SOLUTION

Accepted Solutions
Hall of Fame Super Gold

Re: USA Calling UK

Configure;

int Se0/0/0:23

isdn map address . type unknown plan unknown

There are NO adverse consequences and NO risks in doing that, and it can be done at ANY time.

Please remember to rate useful posts clicking on the stars below.

5 REPLIES
Hall of Fame Super Gold

Re: USA Calling UK

Are you using MGCP or h.323 ?

New Member

Re: USA Calling UK

HI,

I'm using H.323. Calling other countries, I connect perfectly. UK, no go.


Thanks

Hall of Fame Super Gold

Re: USA Calling UK

Configure;

int Se0/0/0:23

isdn map address . type unknown plan unknown

There are NO adverse consequences and NO risks in doing that, and it can be done at ANY time.

Please remember to rate useful posts clicking on the stars below.

New Member

Re: USA Calling UK

Thanks.

That works now.

Cheers

Hall of Fame Super Gold

Re: USA Calling UK

Very good, thank you for the nice rating and good luck.

311
Views
0
Helpful
5
Replies
CreatePlease login to create content