Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

Users wants to have their Actual DID on Outgoing Calls

Hi All,

We are using CUCM System version: 8.5.1. we have a Board line number +91 44 4404 4000, the DIDs starts from +91 44 4404 4000 to +91 44 4404 4099.

at present when the user dial an outbound call their number displays as +91 44 4404 4000 (Board line number), but they want their actual DID to be displayed instead.

 

Please assist.

let me know for any clarification.

Thanks in Advance.

SIva.

 

9 REPLIES
New Member

can you post the voice

can you post the voice gateway config

New Member

voice-card 0!!!voice service

voice-card 0
!
!
!
voice service voip
 allow-connections h323 to h323
 allow-connections h323 to sip
 allow-connections sip to h323
 allow-connections sip to sip
 supplementary-service h450.12
 fax protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback none
 h323
  h225 h245-address on-connect
 sip
  registrar server expires max 3600 min 3600
!
voice class codec 99
 codec preference 1 g711ulaw
!
voice class h323 1
  h225 timeout tcp establish 3
!

hw-module pvdm 0/0

!

controller E1 0/0/0
 framing NO-CRC4 
 pri-group timeslots 1-31 service mgcp
!
controller E1 0/0/1
 framing NO-CRC4 
 pri-group timeslots 1-31 service mgcp

!

interface Serial0/0/0:15
 no ip address
 encapsulation hdlc
 isdn switch-type primary-net5
 isdn incoming-voice voice
 isdn bind-l3 ccm-manager
 no cdp enable

!

ccm-manager redundant-host 192.168.1.11
ccm-manager mgcp
no ccm-manager fax protocol cisco
ccm-manager music-on-hold
ccm-manager config server 192.168.1.10 192.168.1.11
ccm-manager config
ccm-manager sccp local GigabitEthernet0/0

!

mgcp
mgcp call-agent 192.168.1.10 2427 service-type mgcp version 0.1
mgcp rtp unreachable timeout 1000 action notify
mgcp modem passthrough voip mode nse
mgcp package-capability rtp-package
mgcp package-capability sst-package
mgcp package-capability pre-package
no mgcp package-capability res-package
no mgcp timer receive-rtcp
mgcp sdp simple
mgcp fax t38 inhibit
mgcp rtp payload-type g726r16 static
mgcp bind control source-interface GigabitEthernet0/0
mgcp bind media source-interface GigabitEthernet0/0
!
mgcp profile default

New Member

in case of MGCP the

in case of MGCP the configuration is in the CUCM

check the transform mask in the dial patterns. also check the translation patterns

Cisco Employee

The easiest way would be to

The easiest way would be to hardcode their own external phone number mask at DN level, and then make sure to check the option in the RP to use it for outbound calls.

HTH

java

if this helps, please rate

www.cisco.com/go/pdi
New Member

Hi Siva, In this case please

Hi Siva,

 

In this case please let us know if the internal extensions have the same mask i.e 4000 to 4099 or different extensions.

 

Regards,
Mohamed Bedawy

Regards, Mohamed Helmy
New Member

Hi Mohamed,Internal

Hi Mohamed,

Internal extensions have different mask 

+91 44 4404 4000 to +91 44 4404 4099   >>  9200 to 9299

 

Regards,

Siva.

New Member

Hi Mohamed,  Any idea..

Hi Mohamed, 

 

Any idea..

 

Thanks,

SIva.

New Member

hi Siva, as the extensions

hi Siva,

 

as the extensions are not in the same range, so the best way will be as our expert Jaime said. hard code each directory number with external phone number musk with his external number.

other ways will take a lot of work.

 

Regards.

 

Regards, Mohamed Helmy
New Member

Go toCall Routing > Route

Go to

Call Routing > Route/Hunt > Route List > (Choose the Route List used by your route pattern then click on it)

After, click on Route List Details (figure 1.png) and make sure that the field Use Calling Party's External Phone Number Mask Required Field is set to Active (figure 2.png)

Hope this helps!

88
Views
5
Helpful
9
Replies