Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

VG 202 MGCP no dialtone

I'm configuring a VG202 using the MGCP protocol. However, I get no dialtone.

CUCM = 192.168.8.11

show running-config (VG202):

VG202-1#show run

Building configuration...

Current configuration : 1764 bytes

!

version 12.4

no service pad

service timestamps debug datetime msec

service timestamps log datetime msec

no service password-encryption

!

hostname VG202-1

!

boot-start-marker

boot-end-marker

!

logging message-counter syslog

!

no aaa new-model

ip source-route

!

!

!

!

ip cef

no ipv6 cef

!

!

!

!

!

!

voice service voip

!

!

!

!

!

!

!

!

!

!

!

!

!

voice-card 0

!

username fcs privilege 15 secret 5 $1$YgWh$LpHoJnoGfLkOCM8sbXO8h.

archive

log config

  hidekeys

!

!

!

!

!

interface FastEthernet0/0

ip address dhcp

duplex auto

speed auto

!

interface FastEthernet0/1

no ip address

shutdown

duplex auto

speed auto

!

ip forward-protocol nd

!

no ip http server

!

!

!

control-plane

!

!

!

voice-port 0/0

cptone BE

!

voice-port 0/1

cptone BE

!

ccm-manager redundant-host 192.168.8.11

ccm-manager mgcp

no ccm-manager fax protocol cisco

ccm-manager music-on-hold

ccm-manager config server 192.168.8.11 

ccm-manager config

!

mgcp

mgcp call-agent 192.168.8.11 2427 service-type mgcp version 0.1

mgcp dtmf-relay voip codec all mode out-of-band

mgcp rtp unreachable timeout 1000 action notify

mgcp modem passthrough voip mode nse

mgcp package-capability rtp-package

mgcp package-capability sst-package

no mgcp package-capability res-package

no mgcp package-capability fxr-package

no mgcp timer receive-rtcp

mgcp sdp simple

mgcp fax t38 ecm

mgcp fax t38 gateway force

mgcp rtp payload-type g726r16 static

mgcp bind control source-interface FastEthernet0/0

mgcp bind media source-interface FastEthernet0/0

!

mgcp profile default

!

!

!

dial-peer voice 900 pots

service mgcpapp

port 0/0

!

dial-peer voice 901 pots

service mgcpapp

port 0/1

!

!

!

line con 0

no modem enable

line aux 0

line vty 0 4

privilege level 15

login

!

exception data-corruption buffer truncate

end

show mgcp:

VG202-1#show mgcp

MGCP Admin State ACTIVE, Oper State ACTIVE - Cause Code NONE

MGCP call-agent: 192.168.8.11 2427 Initial protocol service is MGCP 0.1

MGCP validate call-agent source-ipaddr DISABLED

MGCP validate domain name DISABLED

MGCP block-newcalls DISABLED

MGCP send SGCP RSIP: forced/restart/graceful/disconnected DISABLED

MGCP quarantine mode discard/step

MGCP quarantine of persistent events is ENABLED

MGCP dtmf-relay voip codec all mode out-of-band

MGCP dtmf-relay for voAAL2 is SDP controlled

MGCP voip modem passthrough mode: NSE, codec: g711ulaw, redundancy: DISABLED,

MGCP voaal2 modem passthrough disabled

MGCP voip modem relay: Disabled

MGCP T.38 Named Signalling Event (NSE) response timer: 200

MGCP Network (IP/AAL2) Continuity Test timer: 200

MGCP 'RTP stream loss' timer disabled

MGCP request timeout 500

MGCP maximum exponential request timeout 4000

MGCP rtp unreachable timeout 1000 action notify

MGCP gateway port: 2427, MGCP maximum waiting delay 3000

MGCP restart delay 0, MGCP vad DISABLED

MGCP rtrcac DISABLED

MGCP system resource check DISABLED

MGCP xpc-codec: DISABLED, MGCP persistent hookflash: DISABLED

MGCP persistent offhook: ENABLED, MGCP persistent onhook: DISABLED

MGCP piggyback msg ENABLED, MGCP endpoint offset DISABLED

MGCP simple-sdp ENABLED

MGCP undotted-notation DISABLED

MGCP codec type g711ulaw, MGCP packetization period 20

MGCP JB threshold lwm 30, MGCP JB threshold hwm 150

MGCP LAT threshold lwm 150, MGCP LAT threshold hwm 300

MGCP PL threshold lwm 1000, MGCP PL threshold hwm 10000

MGCP CL threshold lwm 1000, MGCP CL threshold hwm 10000

MGCP playout mode is adaptive 60, 40, 1000 in msec

MGCP Fax Playout Buffer is 300 in msec

MGCP media (RTP) dscp: ef, MGCP signaling dscp: af31

MGCP default package: line-package

MGCP supported packages: gm-package dtmf-package trunk-package line-package

                         hs-package rtp-package atm-package ms-package dt-package

                         mt-package sst-package md-package

MGCP Digit Map matching order: shortest match

SGCP Digit Map matching order: always left-to-right

MGCP VoAAL2 ignore-lco-codec DISABLED

MGCP T.38 Max Fax Rate is DEFAULT

MGCP T.38 Fax is ENABLED

MGCP T.38 Fax ECM is ENABLED

MGCP T.38 Fax NSF Override is DISABLED

MGCP T.38 Fax Low Speed Redundancy: 0

MGCP T.38 Fax High Speed Redundancy: 0

MGCP Fax relay SG3-to-G3: ENABLED

MGCP Fax relay ANSam suppression: DISABLED

MGCP control bound to interface FastEthernet0/0

MGCP media bound to interface FastEthernet0/0

MGCP Upspeed payload type for G711ulaw: 0,  G711alaw: 8

MGCP Dynamic payload type for Cisco fax indication: 96, Cisco fax ack: 97

MGCP Static payload type for G.726-16K codec

MGCP Dynamic payload type for G.726-24K codec

MGCP Dynamic payload type for G.726-32K codec

MGCP Dynamic payload type for G.Clear codec

MGCP Dynamic payload type for NSE is 100

MGCP Dynamic payload type for NTE is 99

MGCP rsip-range is enabled for TGCP only.

MGCP Comedia role is NONE

MGCP Comedia check media source is DISABLED

MGCP Comedia SDP force is DISABLED

MGCP g729 variants use static payload type and contain annexb in SDP

MGCP Guaranteed scheduler time is DISABLED

MGCP Disconnect delay error recovery DISABLED

MGCP DNS stale threshold is 30 seconds

show ccm:

VG202-1#show ccm

MGCP Domain Name: VG202-1.genk.be

Priority        Status                   Host

============================================================

Primary         Registering with CM      192.168.8.11

First Backup    Duplicate of Primary     192.168.8.11

Second Backup   None                    

Current active Call Manager:    None

Backhaul/Redundant link port:   2428

Failover Interval:              30 seconds

Keepalive Interval:             15 seconds

Last keepalive sent:            01:23:38 UTC Mar 1 2002 (elapsed time: 00:08:23)

Last MGCP traffic time:         01:31:47 UTC Mar 1 2002 (elapsed time: 00:00:14)

Last failover time:             None

Last switchback time:           None

Switchback mode:                Graceful

MGCP Fallback mode:             Not Selected

Last MGCP Fallback start time:  None

Last MGCP Fallback end time:    None

MGCP Download Tones:            Disabled

TFTP retry count to shut Ports: 2

Configuration Auto-Download Information

=======================================

No configurations downloaded

Current state: Downloading XML file

Configuration Download statistics:

        Download Attempted             : 1

          Download Successful          : 0

          Download Failed              : 0

        Configuration Attempted        : 0

          Configuration Successful     : 0

          Configuration Failed(Parsing): 0

          Configuration Failed(config) : 0

Last config download command:

FAX mode: disable

Configuration Error History:

On the CUCM the gateway is configured, and has a line associated with the port I want to use. Can anybody point me to what is wrong?

1 ACCEPTED SOLUTION

Accepted Solutions
VIP Super Bronze

VG 202 MGCP no dialtone

VG202-1#show ccm

MGCP Domain Name: VG202-1.genk.be

Priority        Status                   Host

============================================================

Primary         Registering with CM      192.168.8.11

First Backup    Duplicate of Primary     192.168.8.11

Second Backup   None                   

Your vg202 ports are not registered with the CUCM.  The mgcp domain name shows vg202-1.genke.be...is this what is configured in cucm?

Your vg202 hostname doesnt match this...your hostname including if you have ip domain name configured needs to match what ypu have in cucm..

Please rate all useful posts

"opportunity is a haughty goddess who waste no time with those who are unprepared"

Please rate all useful posts "The essence of christianity is not the enthronement but the obliteration of self --William Barclay"
2 REPLIES
VIP Super Bronze

VG 202 MGCP no dialtone

VG202-1#show ccm

MGCP Domain Name: VG202-1.genk.be

Priority        Status                   Host

============================================================

Primary         Registering with CM      192.168.8.11

First Backup    Duplicate of Primary     192.168.8.11

Second Backup   None                   

Your vg202 ports are not registered with the CUCM.  The mgcp domain name shows vg202-1.genke.be...is this what is configured in cucm?

Your vg202 hostname doesnt match this...your hostname including if you have ip domain name configured needs to match what ypu have in cucm..

Please rate all useful posts

"opportunity is a haughty goddess who waste no time with those who are unprepared"

Please rate all useful posts "The essence of christianity is not the enthronement but the obliteration of self --William Barclay"
New Member

VG 202 MGCP no dialtone

Hi aokanlawon.

I had in CUCM put VG202-01.genk.be, so a small typo I was looking over each time. Thanks!

Thanks!

346
Views
0
Helpful
2
Replies