Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

VIC2-2BRI-NT/TE - no voice port

Hi,

I want to use a VIC2-2BRI-NT/TE with a 2811 router for trunking with a PBX but no voice port exists on the router. Do I have to create it somehow? The config looks like this:

show diag:

WIC Slot 0:

VIC2 - BRI-NT/TE Voice daughter card (2 port)

Hardware Revision : 1.1

Top Assy. Part Number : 800-21861-03

Board Revision : B0

Deviation Number : 0-0

Fab Version : 02

PCB Serial Number : FOC11286XWM

RMA Test History : 00

RMA Number : 0-0-0-0

RMA History : 00

Product (FRU) Number : VIC2-2BRI-NT/TE

Version Identifier : V02

CLEI Code : CNUIAVZAAA

EEPROM format version 4

show run:

interface BRI0/0/0

no ip address

isdn switch-type basic-net3

isdn overlap-receiving

isdn protocol-emulate network

isdn layer1-emulate network

isdn incoming-voice voice

isdn sending-complete

isdn skipsend-idverify

show isdn stat:

Global ISDN Switchtype = basic-net3

ISDN BRI0/0/0 interface

******* Network side configuration *******

dsl 0, interface ISDN Switchtype = basic-net3

Layer 1 Status:

ACTIVE

Layer 2 Status:

TEI = 64, Ces = 1, SAPI = 0, State = MULTIPLE_FRAME_ESTABLISHED

Layer 3 Status:

0 Active Layer 3 Call(s)

Active dsl 0 CCBs = 0

The Free Channel Mask: 0x80000003

show ver:

Cisco IOS Software, 2800 Software (C2800NM-IPVOICEK9-M), Version 12.4(24)T, RELEASE SOFTWARE (fc1)

10 REPLIES
Hall of Fame Super Gold

Re: VIC2-2BRI-NT/TE - no voice port

You also need a DSP module, a minimum of PVDM2-8.

New Member

Re: VIC2-2BRI-NT/TE - no voice port

Tanks!

New Member

Re: VIC2-2BRI-NT/TE - no voice port

Same need, same issue,

1751V with wic 1bri S/T +

PVDM-256K-4

Should I use VIC BRI NT/TE card or a different dsp ???

Thanks

Hall of Fame Super Gold

VIC2-2BRI-NT/TE - no voice port

You need VIC card for Voice.

WIC card is for WAN.

New Member

VIC2-2BRI-NT/TE - no voice port

It was a newbie question.....

Tried with a VIC2B-NT/TE , it works like a charm ....

Thanks

Hall of Fame Super Gold

Re: VIC2-2BRI-NT/TE - no voice port

Thank you for the nice rating and good luck!h

New Member

VIC2-2BRI-NT/TE - no voice port

Paolo,

As said my 1751V is now equipped with a VIC 2B NT/TE on slot 0 plus a PVDM-256K-4

All is working fine

I tried to install a VIC 2FXS card on slot 2

The system recognize both cards (show diag) but only voice port 2/0 and 2/1 are present on sh run

voice port 0/0 and 0/1 disappeared (the BRI port)

Why is this ??

Should I upgrade something (PVDM, RAM etc.)

Thanks

Hall of Fame Super Gold

VIC2-2BRI-NT/TE - no voice port

Post "show inventory".

New Member

VIC2-2BRI-NT/TE - no voice port

I've found this in official Cisco web resource :

Part NumberDescriptionNumber of DSPsSupported Voice Ports (Calls)
PVDM-44-channel PVDM12
PVDM-88-channel PVDM24

so a PVDM-4 can manage only two ports

for a further voice card  i need a PVDM-4 more (or replace the current one with a PVDM-8)

Thank you anyway

Hall of Fame Super Gold

Re: VIC2-2BRI-NT/TE - no voice port

That is, as I had mentioned in my first answer above.

1037
Views
10
Helpful
10
Replies