Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

VIC2-2FXO and VIC2-2FXS on cisco 2801

Hello,

I am having Cisco 2801 router with IOS "c2801-ipvoicek9-mz.124-20.T5.bin", i have installed VIC2-FXO on slot 2 [ this slot accepts only WICs and VICs] and VIC2-2FXS on slot0 [This slot only accepts VICs]

but the problem is that they both are not showing in show run and  show voice port summmary command.

i issued command show diag and found the below out for both slot:

VIC Slot 0:

        FXS Voice daughter card (2 port)

        WIC module not supported/disabled in this slot

        Hardware revision 1.1           Board revision B0

        Serial number     27276672      Part number    800-02493-04

        FRU Part Number     VIC-2FXS=

        Test history      0x0           RMA number     00-00-00

        Connector type    Wan Module

        EEPROM format version 1

        EEPROM contents (hex):

          0x20: 01 0E 01 01 01 A0 35 80 50 09 BD 04 00 00 00 00

          0x30: 58 00 00 00 01 12 27 01 FF FF FF FF FF FF FF FF

        WIC/VIC/HWIC Slot 1:

        4 Port FE Switch

        Base MAC Address         : 001a.6d50.cbfc

        MAC Address block size   : 4

        PCB Serial Number        : FOC10484E9S

        Hardware Revision        : 6.0

        Part Number              : 73-8474-06

        Board Revision           : A0

        Top Assy. Part Number    : 800-24193-02

        Deviation Number         : 0

        Fab Version              : 05

        CLEI Code                : IPUIA00RAA

        RMA Test History         : 00

        RMA Number               : 0-0-0-0

        RMA History              : 00

        Product (FRU) Number     : HWIC-4ESW

        Version Identifier       : V01

        Connector Type           : 01

        EEPROM format version 4

        EEPROM contents (hex):

          0x00: 04 FF CF 06 00 1A 6D 50 CB FC 43 00 04 C1 8B 46

          0x10: 4F 43 31 30 34 38 34 45 39 53 40 00 56 41 06 00

          0x20: 82 49 21 1A 06 42 41 30 C0 46 03 20 00 5E 81 02

          0x30: 88 00 00 00 00 02 05 C6 8A 49 50 55 49 41 30 30

          0x40: 52 41 41 03 00 81 00 00 00 00 04 00 CB 89 48 57

          0x50: 49 43 2D 34 45 53 57 89 56 30 31 20 D9 02 C1 40

          0x60: 05 01 FF FF FF FF FF FF FF FF FF FF FF FF FF FF

          0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

        WIC/VIC Slot 2:

        FXO Voice daughter card (2 port)

        Unknown EEPROM ver 16

        EEPROM format version 16

        EEPROM contents (hex):

          0x20: 10 0D 01 01 01 A0 C2 85 50 09 BF 01 00 00 00 00

          0x30: A0 00 00 00 02 01 09 01 FF FF FF FF FF FF FF FF

        WIC/VIC/HWIC Slot 3:

        Serial 2T (12in1)

        Hardware revision 1.0           Board revision D0

        Serial number     35386517      Part number    800-03181-01

        FRU Part Number     WIC-2T=

        Test history      0x0           RMA number     00-00-00

        Connector type    PCI

        EEPROM format version 1

        EEPROM contents (hex):

          0x20: 01 12 01 00 02 1B F4 95 50 0C 6D 01 00 00 00 00

          0x30: 68 00 00 00 00 09 02 00 FF FF FF FF FF FF FF FF

please help!

3 REPLIES
Hall of Fame Super Gold

Re: VIC2-2FXO and VIC2-2FXS

You need IOS version 12.4(20)T.

Cisco IP Communications Voice/Fax Network Module
http://www.cisco.com/en/US/prod/collateral/modules/ps5365/product_data_sheet0900aecd801c595e.html

Please don't forget to rate useful posts.  Thanks.

New Member

Re: VIC2-2FXO and VIC2-2FXS

Hi,

I have managed to arrange the IOS "c2801-ipvoicek9-mz.124-20.T5.bin", but still the same problem.

please help!

New Member

Re: VIC2-2FXO and VIC2-2FXS

experts! i would appreciate the quick response

310
Views
0
Helpful
3
Replies