Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
New Member

vic2-2fxo not supported in 2811?

i have a nm-hdv in slot one and a vic2-2fxo in the module. this 2811 has four hwic slots - can i put the vic2-2fxo in an hwic?

sh diag

Slot 1:

High Density Voice Port adapter

Port adapter is analyzed

Port adapter insertion time unknown

EEPROM contents at hardware discovery:

Hardware Revision : 1.1

Top Assy. Part Number : 800-03567-01

Board Revision : G0

Deviation Number : 0-0

Fab Version : 02

PCB Serial Number : JAE07420BVK

RMA Test History : 00

RMA Number : 0-0-0-0

RMA History : 00

Product (FRU) Number : NM-HDV=WIC Slot 0:

VG - FXO Voice daughter card (2 port)

WIC module not supported/disabled in this slot

Hardware Revision : 5.0

Top Assy. Part Number : 800-21597-01

Board Revision : E0

Deviation Number : 0-0

Fab Version : 04

PCB Serial Number : FOC09301FGD

RMA Test History : 00

RMA Number : 0-0-0-0

RMA History : 00

Version Identifier : V

Product (FRU) Number : VIC2-2FXO=

thanks in advance.

1 ACCEPTED SOLUTION

Accepted Solutions
Hall of Fame Super Gold

Re: vic2-2fxo not supported in 2811?

That is what I was telling you ... The ISR routers are really made to work this way ...

9 REPLIES
Hall of Fame Super Gold

Re: vic2-2fxo not supported in 2811?

Yes, but you need the DSP modules on the router mainboard. The smaller is PVDM2-8 and will support 8 voice channels.

Hope this helps, please rate post if it does!

New Member

Re: vic2-2fxo not supported in 2811?

ok - im configuring this as a 911 line at a remote site. ill dig up DSP's and give it a shot.

thanks for the reply.

New Member

Re: vic2-2fxo not supported in 2811?

i have a pvdm2-64 sitting in a nm-hdv2-2t1/e1 - will this work?

Hall of Fame Super Gold

Re: vic2-2fxo not supported in 2811?

Yes, although hugely oversized.

New Member

Re: vic2-2fxo not supported in 2811?

you said to put the pvdm2 on the motherboard and not on the nm-hdv?

New Member

Re: vic2-2fxo not supported in 2811?

i already have dsp on the motherboard.

PVDM Slot 0:

16-channel (G.711) Voice/Fax PVDMII DSP SIMM PVDM daughter card

Hardware Revision : 4.0

Part Number : 73-8538-05

Board Revision : B0

Deviation Number : 0

Fab Version : 04

PCB Serial Number : FOC1144176Z

RMA Test History : 00

RMA Number : 0-0-0-0

RMA History : 00

Processor type : 00

Product (FRU) Number : PVDM2-16

Version Identifier : V01

EEPROM format version 4

PVDM Slot 1:

48-channel (G.711) Voice/Fax PVDMII DSP SIMM PVDM daughter card

Hardware Revision : 4.0

Part Number : 73-8540-05

Board Revision : B0

Deviation Number : 0

Fab Version : 04

PCB Serial Number : FOC11372FMR

RMA Test History : 00

RMA Number : 0-0-0-0

RMA History : 00

Processor type : 00

Product (FRU) Number : PVDM2-48

Version Identifier : V01

EEPROM format version 4

EEPROM contents (hex):

New Member

Re: vic2-2fxo not supported in 2811?

analog cards are not supported on NM-HDV per the link below.

http://www.cisco.com/en/US/customer/products/hw/routers/ps259/products_tech_note09186a00800e73f6.shtml

i'm going to try a chassis slot.

Hall of Fame Super Gold

Re: vic2-2fxo not supported in 2811?

That is what I was telling you ... The ISR routers are really made to work this way ...

New Member

Re: vic2-2fxo not supported in 2811?

so i ended up removing the nm-hdv from slot 1 in the 2811 and adding the VIC2-2FXO in hwic slot 3 and the router found it - no more errors during a sh diag.

thanks.

873
Views
0
Helpful
9
Replies
CreatePlease to create content