VIC3-4FXO/DID module not detect in 2801 Router.

[MANAS RANJAN BEHERA]

Hi Team,

I have Cisco 2801 router with 2 DSP 16 Channel, 128 MB DRAM and 128 MB flash. I am using IOS c2801-spservicesk9-mz.124-3i but the VIC3-4FXO/DID module is not detected. I tried to upgrade the IOS to 15.0 and 15.1 but the router is not boot up due to insufficient memory.  In that IOS the FXO card is detected.  I checked the data sheet of both router and FXO card it support 12.4T IOS but when I upload the IOS and try to boot same problem I have faced (router not boot due to insufficient memory).  Kindly help me find out the appropriate IOS to resolve the issue.

Thanks in advance.

Regards, 

Manas Ranjan

[Aman Soi]

Hi Manas,

I was trying to find the support for VIC3-4FXO card on 2801 router. What I could find that VIC3 cards require IP Voice image with IOS version 12.4(20)T or 12.4(15)XW. 

even though 12.4(15)XW is not available but 12.4(15)XY  is available but IP voice image requires minimum 192MB DRAM with 64 MB Flash.So , u need to upgrade the DRAM.

http://www.cisco.com/c/en/us/products/collateral/interfaces-modules/ip-communications-voice-fax-network-modules/product_data_sheet0900aecd801c595e.html

regds,

aman

[Tagir Temirgaliyev]

VIC3-4FXO card is not supported in 2801 according to table4 

Table 4. Software and Memory Requirements for Voice/Fax Network Modules and Voice Interface Cards

Product	Cisco 2800 Series	Cisco 3800 Series	Cisco 2900 and 3900 Series
NM-HD-1V NM-HD-2V NM-HD-2VE	• Cisco IOS Software • Release 12.3(8)T4 • "IP Voice" images	• Cisco IOS Software • Release 12.3(11)T • "IP Voice" images	• Cisco IOS Software Release 15.0(1)M • "UC Technology" images
VIC2-2FXO VIC2-4FXO VIC2-2BRI-NT/TE	• Cisco IOS Software • Release 12.3(8)T4 • "IP Voice" images	• Cisco IOS Software • Release 12.3(11)T • "IP Voice" images	• Cisco IOS Software Release 15.0(1)M • "UC Technology" images
VWIC2-xMFT-xx	• Cisco IOS Software • Release 12.3(14)T • "IP Voice" images	• Cisco IOS Software • Release 12.3(14)T • "IP Voice" images	• Cisco IOS Software Release 15.0(1)M • "UC Technology" images
VIC3-2E/M	• Cisco IOS Software • Release 12.4(15)XW or 12.4(20)T • "IP Voice" images	• Cisco IOS Software • Release 12.4(15)XW or 12.4(20)T • "IP Voice" images	• Cisco IOS Software Release 15.0(1)M • "UC Technology" images
VIC3-2FXS/DID VIC3-2FXS-E/DID VIC3-4FXS/DID	• Cisco IOS Software • Release 12.4(15)XZ or 12.4(20)T • "IP Voice" images	• Cisco IOS Software • Release 12.4(15)XZ or 12.4(20)T • "IP Voice" images	• Cisco IOS Software Release 15.0(1)M • "UC Technology" images

[khorheesoo]

If you are running IOS 15.X and above especially for Voice related items dont go for bare minumum. Try at least 384MB or 512MB depending on your load. I dont know what else you maybe running on it.

http://www.cisco.com/c/en/us/products/collateral/ios-nx-os-software/ios-packaging/product_bulletin_c25-557281.html

[Anas Abueideh]

vic2-4fxo is not supported in 2800/3800 series

HTH

Anas

don't forget to rate helpful posts

[Tagir Temirgaliyev]

Anas

vic2-4fxo is  supported in 2800

vic3-4fxo is not supported in 2800