Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

Voice gateway problem Call not receive debug isdn q931 output

Hello , I have a  problem with cisco 2921  voice gateway (PRI) Could you please someone explain me about someting.

Debug and and Dial peers output is below,

Thanks Advance

Jun  1 17:59:16.839: ISDN Se0/0/0:15 Q931: RX <- SETUP pd = 8  callref = 0x17FF

        Bearer Capability i = 0x8090A3

                Standard = CCITT

                Transfer Capability = Speech

                Transfer Mode = Circuit

                Transfer Rate = 64 kbit/s

        Channel ID i = 0xA98392

                Exclusive, Channel 18

        Progress Ind i = 0x8283 - Origination address is non-ISDN

        Calling Party Number i = 0x2181, '05551112223'

                Plan:ISDN, Type:National

        Called Party Number i = 0xC1, '6727498'

                Plan:ISDN, Type:Subscriber(local)

        Sending Complete

Jun  1 17:59:16.847: ISDN Se0/0/0:15 Q931: TX -> CALL_PROC pd = 8  callref = 0x97                                        FF

        Channel ID i = 0xA98392

                Exclusive, Channel 18

Tadim_VG02#

Jun  1 17:59:16.847: ISDN Se0/0/0:15 Q931: TX -> DISCONNECT pd = 8  callref = 0x9                                        7FF

        Cause i = 0x809B - Destination out of order

Jun  1 17:59:16.983: ISDN Se0/0/0:15 Q931: RX <- RELEASE pd = 8  callref = 0x17FF

Jun  1 17:59:17.007: ISDN Se0/0/0:15 Q931: TX -> RELEASE_COMP pd = 8  callref = 0      

Jun  1 18:01:05.467: ISDN Se0/0/0:15 Q931: TX -> SETUP pd = 8  callref = 0x0003

        Sending Complete

        Bearer Capability i = 0x8090A3

                Standard = CCITT

                Transfer Capability = Speech

                Transfer Mode = Circuit

                Transfer Rate = 64 kbit/s

        Channel ID i = 0xA98381

                Exclusive, Channel 1

        Progress Ind i = 0x8083 - Origination address is non-ISDN

        Calling Party Number i = 0x2181, '2626727380'

                Plan:ISDN, Type:National

        Called Party Number i = 0xC1, '03444131834'

                Plan:ISDN, Type:Subscriber(local)

Jun  1 18:01:05.587: ISDN Se0/0/0:15 Q931: RX <- CALL_PROC pd = 8  callref = 0x8003

        Channel ID i = 0xA98381

                Exclusive, Channel 1

Tadim_VG02#

Jun  1 18:01:07.087: ISDN Se0/0/0:15 Q931: RX <- ALERTING pd = 8  callref = 0x8003

        Progress Ind i = 0x8482 - Destination address is non-ISDN

Tadim_VG02#

Jun  1 18:01:11.735: ISDN Se0/0/0:15 Q931: RX <- CONNECT pd = 8  callref = 0x8003

Jun  1 18:01:11.739: ISDN Se0/0/0:15 Q931: TX -> CONNECT_ACK pd = 8  callref = 0x0003

Tadim_VG02#

Jun  1 18:01:16.687: ISDN Se0/0/0:15 Q931: RX <- FACILITY pd = 8  callref = 0x8003

        Facility i = 0x91A112020170020122300AA1053003020101820100

                Protocol Profile = Remote Operations Protocol

                0xA112020170020122300AA1053003020101820100

                Component = Invoke component

                        Invoke Id = 112

                        Operation = AOCDChargingUnit

Tadim_VG02#

Jun  1 18:01:36.071: ISDN Se0/0/0:15 Q931: TX -> DISCONNECT pd = 8  callref = 0x0003

        Cause i = 0x8090 - Normal call clearing

Jun  1 18:01:36.387: ISDN Se0/0/0:15 Q931: RX <- RELEASE pd = 8  callref = 0x8003

        Facility i = 0x91A11102017502012430093007A1053003020101

                Protocol Profile = Remote Operations Protocol

                0xA11102017502012430093007A1053003020101

                Component = Invoke component

                        Invoke Id = 117

                        Operation = AOCECharging Unit

Jun  1 18:01:36.407: ISDN Se0/0/0:15 Q931: TX -> RELEASE_COMP pd = 8  callref = 0x0003

DİAL PEERS

dial-peer voice 120 voip

incoming called-number .T

codec g711ulaw

dial-peer voice 130 pots

destination-pattern 05.........

port 0/0/0:15

prefix 05

dial-peer voice 20 pots

destination-pattern 9[2-9]......

port 0/0/0:15

forward-digits 7

dial-peer voice 21 pots

destination-pattern 90[2-4].........

port 0/0/0:15

forward-digits 11

dial-peer voice 22 pots

destination-pattern 905.........

port 0/0/0:15

forward-digits 11

dial-peer voice 23 pots

destination-pattern 900T

port 0/0/0:15

forward-digits all

1 REPLY
Cisco Employee

Voice gateway problem Call not receive debug isdn q931 output

The first call to 6727498 doesn't match any dial peers and fails.

The second call matches dial peer 130.

What specific info are you looking for?

2046
Views
0
Helpful
1
Replies