Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
New Member

VOIP: I cannot be heard by remote users

Hi all,

I manage a network whereby the branches are connected with VOIP using pots connected to local PABX. All has been well till yesterday when one branch cannot hear callers from the central site. I have tried checking all that i know of VOIP but in vain. Please, i need someone to point me in the right direction.

My background is routing and switching.

"What would make the remote users fail to hear me. I can hear them clearly"

7 REPLIES
New Member

Re: VOIP: I cannot be heard by remote users

In my experience the only time I had this happen is when the Voip phones had somehow gotten an IP that was on the data side of the network instead of in the voice vlan where it belonged. This caused the user to only get audio in one direction.

New Member

Re: VOIP: I cannot be heard by remote users

I'm actually not using VOIP phones. I am using analogue pots connected to local PABX and remote PABX. Normal landline calls are OK currently.

New Member

Re: VOIP: I cannot be heard by remote users

May be worth checking that nobody has messed about with your routing.

I assume that you have done this considering the R&S background but it is very easy to think its something to do with voice, thus overlooking the foundation that the voice requires to run over.

Definitely have route both ways for Voice VLANs? No new access lists blocking Voice subnet for the return leg etc etc....?

Re: VOIP: I cannot be heard by remote users

Here's a little document I've been writing. There's a page in here for one-way audio.

New Member

Re: VOIP: I cannot be heard by remote users

output from "show call active voice brief" both from the gw and the remote site:

VOIP-GW#show call active voice brief

: hs. + pid:

dur hh:mm:ss tx:/ rx:/

IP : rtt:

delay://ms

media inactive detected: media cntrl rcvd: timestamp:

MODEMPASS buf:/ loss /

last s dur:/s

FR [int dlci cid] vad: dtmf: seq:

(payload size)

ATM [int vpi/vci cid] vad: dtmf: seq:

(payload size)

Tele (callID) [channel_id] tx://ms noise: acom: i/o:/ dBm

MODEMRELAY info:// xid:/ total://

speeds(bps): local / remote /

Proxy :

bw: / codec:

tx:

rx:

Telephony call-legs: 1

SIP call-legs: 0

H323 call-legs: 1

Call agent controlled call-legs: 0

SCCP call-legs: 0

Multicast call-legs: 0

Total call-legs: 2

3E7C : 94603 434299274ms.1 +13050 pid:3000 Answer 203293153 active

dur 00:00:03 tx:424/11815 rx:427/8377

Tele 0/3/0:15 (94603) [0/3/0.10] tx:16190/8440/0ms g729r8 noise:-84 acom:45 i/0:-49/-74 dBm

3E7C : 94604 434299274ms.2 +13040 pid:1000 Originate 52 active

dur 00:00:03 tx:427/8377 rx:424/8423

IP 10.206.124.253:16704 SRTP: off rtt:0ms pl:6850/20ms lost:1/1/0 delay:60/60/70ms g729r8

media inactive detected:n media contrl rcvd:n/a timestamp:n/a

Telephony call-legs: 1

SIP call-legs: 0

H323 call-legs: 1

Call agent controlled call-legs: 0

SCCP call-legs: 0

Multicast call-legs: 0

Total call-legs: 2

VOIP-GW#

052R#show call active voice brief

: hs. + pid:

dur hh:mm:ss tx:/ rx:/

IP : rtt:

delay://ms

media inactive detected: media cntrl rcvd: timestamp:

MODEMPASS buf:/ loss /

last s dur:/s

FR [int dlci cid] vad: dtmf: seq:

(payload size)

ATM [int vpi/vci cid] vad: dtmf: seq:

(payload size)

Tele (callID) [channel_id] tx://ms noise: acom: i/o:/ dBm

MODEMRELAY info:// xid:/ total://

speeds(bps): local / remote /

Proxy :

bw: / codec:

tx:

rx:

Telephony call-legs: 1

SIP call-legs: 0

H323 call-legs: 1

MGCP call-legs: 0

Multicast call-legs: 0

Total call-legs: 2

3E97 : 6063 796032798hs.1 +1692 pid:1000 Answer 203293318 active

dur 00:00:14 tx:546/10767 rx:290/5743

IP 172.31.113.111:18042 rtt:34ms pl:0/0ms lost:1/0/0 delay:70/260/10ms g729r8

media inactive detected:n media contrl rcvd:n/a timestamp:n/a

3E97 : 6064 796032799hs.1 +1690 pid:200 Originate 52 active

dur 00:00:14 tx:297/5883 rx:546/10767

Tele 0/3/1 (6064) [0/3/1] tx:31840/10830/0ms g729r8 noise:-55 acom:6 i/0:-56/-79 dBm

Telephony call-legs: 1

SIP call-legs: 0

H323 call-legs: 1

MGCP call-legs: 0

Multicast call-legs: 0

Total call-legs: 2

052R#

New Member

Re: VOIP: I cannot be heard by remote users

Previous post is a command output from both remote and cetral site:

I've treied to figure out what the issue could be in vain. Based at the HQ where the gw is located, i can hear the voice from the remote site, but they cannot hear me. If a call is orinated either from HQ or remote site, the results are the same. The voice gateway has only one ethernet interface and terminates other 31 sites which are working OK. The remote site has multiple interfaces and has been working till last saturday when it failed. Can't quite figure out whta could have changed at that time...if any.

Re: VOIP: I cannot be heard by remote users

From the output it looks like analog problems - either you're not getting audio or possible DSP problems.

You can start by reloading the gateways to see if this temporarily restores audio.

hth,

nick

395
Views
0
Helpful
7
Replies
CreatePlease to create content