Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

Wallmount kit for CP-7931

Hi, Can we use both CP-LCKNGWALLMOUNT(Flat) and CP-LCKNGWALLMNT2(Slanted) with CP-7931?

or, CP-7931 can use with only CP-LCKNGWALLMNT2(Slanted)?

When I see the datasheet of CP-7931,

only CP-LCKNGWALLMNT2(Slanted) is on the sheet.

http://www.cisco.com/en/US/prod/collateral/voicesw/ps6788/phones/ps379/ps7062/product_data_sheet0900aecd80534259.html

Your advice will be appreicated.

1 ACCEPTED SOLUTION

Accepted Solutions
Hall of Fame Super Red

Re: Wallmount kit for CP-7931

Hi Katsukiyo,

The problem with the "older" (CP-LCKNGWALLMOUNT) Wall Mount kit is that it uses the Pin holes from the articulating style "footstand" to mount the phone, which is not avalable on the IP Phone models like the 7931,7911,7912 and 7905 (see step b & c below)

b. On the back of the phone's footstand, push out the pins and remove the stand. You might need to use a screwdriver or other pointed device to push out the pins. The pins are firmly set, so it requires significant force to push them out.

c. Attach the bracket by inserting the pins in the same holes vacated by the footstand. The phone's ports should be accessible through the holes in the bracket

http://www.cisco.com/en/US/docs/voice_ip_comm/cuipph/all_models/wallmount/english/install/guide/ippmount.html

So you must use;

CP-LCKNGWALLMNT2=

Universal locking wall-mounting kit

http://www.cisco.com/en/US/prod/collateral/voicesw/ps6788/phones/ps379/ps7062/product_data_sheet0900aecd80534259.html

7905,7911,7912

CP-LCKNGWALLMNT2=

From this guide;

http://www.cisco.com/en/US/products/hw/phones/ps379/products_data_sheet0900aecd8039de52.html

Hope this helps!

Rob

1 REPLY
Hall of Fame Super Red

Re: Wallmount kit for CP-7931

Hi Katsukiyo,

The problem with the "older" (CP-LCKNGWALLMOUNT) Wall Mount kit is that it uses the Pin holes from the articulating style "footstand" to mount the phone, which is not avalable on the IP Phone models like the 7931,7911,7912 and 7905 (see step b & c below)

b. On the back of the phone's footstand, push out the pins and remove the stand. You might need to use a screwdriver or other pointed device to push out the pins. The pins are firmly set, so it requires significant force to push them out.

c. Attach the bracket by inserting the pins in the same holes vacated by the footstand. The phone's ports should be accessible through the holes in the bracket

http://www.cisco.com/en/US/docs/voice_ip_comm/cuipph/all_models/wallmount/english/install/guide/ippmount.html

So you must use;

CP-LCKNGWALLMNT2=

Universal locking wall-mounting kit

http://www.cisco.com/en/US/prod/collateral/voicesw/ps6788/phones/ps379/ps7062/product_data_sheet0900aecd80534259.html

7905,7911,7912

CP-LCKNGWALLMNT2=

From this guide;

http://www.cisco.com/en/US/products/hw/phones/ps379/products_data_sheet0900aecd8039de52.html

Hope this helps!

Rob

929
Views
0
Helpful
1
Replies