CE Router not picking up IPv6 Prefix-Delegation and inserting a static route...
So I have a series of customers that all have various manufacturers of dual stack home routers. They are picking up both IPv4 and IPv6 addresses from me as well as a PD (prefix delegation) for their internal network (typically a /64, sometimes a /56). I am using the ISC KEA DHCPv4/v6 server on my back end.
I've tested the DHCP server and its correctly analyzing the packet requests and sending both an IPv6 address and IPv6 PD (as well as other information) back to the requesting router. The CE-Router (currently a Cisco 7301 IOS 15.2(4)M11 [c7301-adventerprisek9-mz.152-4.M11.bin]) is giving the correct information to the client however the router is NOT inserting a static route into its routing table for the allocated PD. Same behavior both with and without IPv6 traffic-filters
interface GigabitEthernet0/1.121 description ::Tower CE (v121) encapsulation dot1Q 121 ip dhcp relay information option-insert ip dhcp relay information check-reply ip address xxx.xxx.xxx.2 255.255.254.0 ip access-group CE-inbound in ip access-group CE-outbound out ip helper-address xxx.xxx.xxx.xxx standby version 2 standby 121 ip xxx.xxx.xxx.1 standby 121 priority 105 standby 121 preempt standby 121 track 2 decrement 10
! This is our HSRP link-local address on this interface standby 221 ipv6 FE80::121:1 standby 221 priority 105 standby 221 preempt delay minimum 30 standby 221 track 2 decrement 10 ip ospf cost 10
! Set link-local to indicate VLAN and router number ipv6 address FE80::121:2 link-local ipv6 address tower-sjc ::1/64 ipv6 enable
! Turn off the A flag (but still advertise the prefix) ipv6 nd prefix 2604:xxxx:xxxx:1::/64 no-advertise
! Turn on the M flag (for managed configuration via stateful DHCPv6) ipv6 nd managed-config-flag
! Relay to stateful DHCPv6 server ipv6 dhcp relay destination 2604:xxxx:xxxx:xxxx::FEED:200 ipv6 traffic-filter CE-IPv6-inbound in ipv6 traffic-filter CE-IPv6-outbound out ipv6 ospf 101 area 0 ipv6 ospf priority 0 no keepalive
So I've been experimenting with this and the "ipv6 dhcp iana-route-add" statement is supposed to work based on all the documentation I could find (which then allows for propigation in your IGP) however experimenting and testing shows that its not in fact working. Unless there is an error in the configuration I'd say this is a broken command from Cisco IOS
Re: CE Router not picking up IPv6 Prefix-Delegation and inserting a static route...
Not sure how this would be helpful information as it doesn't give me any new information. I already had that for the 15.0 series (I'm running 15.2 as stated originally) so I have no new references to validate against. Also it appears no one from Cisco IPv6 group actually reads these things either.
This is actually a pretty cool feature, i didn't even know it existed until I was looking for a solution to advertise a subnet (prefix in BGP talk), only if a certain condition existed. This is exactly what conditional advertisements does
j ai une question j ai achete un routeur cisco 887VA-k9 , je le configuré avec la configuration ci- dessous
si je le lier avec mon pc portable sur l un de ses ports directement ça marche toute est bien ( la connexion internet + m...
Attached policy provides CLI access to the Cisco 4G router over text messaging. Two files are in the attached .tar file:
2. PDF with instructions on how to load and use the .tcl file.