Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

Stateless nat64 on Cisco ASR1001

Hello, everybody.

I can't solve simple task: trying to configure stateless nat64.

Topology map is in the attachement.

After configuration:

1) Trying to do ping from PC1 (2.2.2.1) to PC2 (192.168.10.100):

C:\Users\Student1>ping 192.168.10.100

Pinging 192.168.10.100 with 32 bytes of data:
Request timed out.
Request timed out.
Request timed out.
Request timed out.

Ping statistics for 192.168.10.100:
    Packets: Sent = 4, Received = 0, Lost = 4 (100% loss),

C:\Users\Student1>

2) Trying to do ping from PC2 to PC1:

C:\Users\Student1>ping 2001:2:3:4:0:1:0202:0201

Обмен пакетами с 2001:2:3:4:0:1:202:201 по с 32 байтами данных:
Заданный узел недоступен.
Заданный узел недоступен.
Заданный узел недоступен.
Заданный узел недоступен.

Статистика Ping для 2001:2:3:4:0:1:202:201:
    Пакетов: отправлено = 4, получено = 0, потеряно = 4
    (100% потерь)

C:\Users\Student1>

3) Here is IPv4routing table on Cisco Router:

2901_Test#sh ip route
Codes: L - local, C - connected, S - static, R - RIP, M - mobile, B - BGP
       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
       E1 - OSPF external type 1, E2 - OSPF external type 2
       i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
       ia - IS-IS inter area, * - candidate default, U - per-user static route
       o - ODR, P - periodic downloaded static route, H - NHRP, l - LISP
       a - application route
       + - replicated route, % - next hop override

Gateway of last resort is not set

      2.0.0.0/8 is variably subnetted, 2 subnets, 2 masks
C        2.2.2.0/24 is directly connected, GigabitEthernet0/1.15
L        2.2.2.10/32 is directly connected, GigabitEthernet0/1.15
      3.0.0.0/8 is variably subnetted, 2 subnets, 2 masks
C        3.3.3.0/24 is directly connected, GigabitEthernet0/1.14
L        3.3.3.1/32 is directly connected, GigabitEthernet0/1.14
      192.168.1.0/24 is variably subnetted, 2 subnets, 2 masks
C        192.168.1.0/24 is directly connected, GigabitEthernet0/0
L        192.168.1.9/32 is directly connected, GigabitEthernet0/0
S     192.168.10.0/24 [1/0] via 3.3.3.10
2901_Test#


4) Here is IPv4 routing table on Cisco ASR1001:

ASR1000_Test#sh ip route
Codes: L - local, C - connected, S - static, R - RIP, M - mobile, B - BGP
       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
       E1 - OSPF external type 1, E2 - OSPF external type 2
       i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
       ia - IS-IS inter area, * - candidate default, U - per-user static route
       o - ODR, P - periodic downloaded static route, H - NHRP, l - LISP
       + - replicated route, % - next hop override

Gateway of last resort is 3.3.3.1 to network 0.0.0.0

S*    0.0.0.0/0 [1/0] via 3.3.3.1
      3.0.0.0/8 is variably subnetted, 2 subnets, 2 masks
C        3.3.3.0/24 is directly connected, GigabitEthernet0/0/1
L        3.3.3.10/32 is directly connected, GigabitEthernet0/0/1
S     192.168.10.0/24 [1/0] via 0.0.0.4, NVI0
ASR1000_Test#


5) Here is IPv6 routing table on Cisco ASR1001:

ASR1000_Test#sh ipv6 route
IPv6 Routing Table - default - 5 entries
Codes: C - Connected, L - Local, S - Static, U - Per-user Static route
       B - BGP, R - RIP, H - NHRP, I1 - ISIS L1
       I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary, D - EIGRP
       EX - EIGRP external, ND - ND Default, NDp - ND Prefix, DCE - Destination
       NDr - Redirect, l - LISP
       O - OSPF Intra, OI - OSPF Inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2
       ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2
C   2001:2:3:4::/64 [0/0]
     via GigabitEthernet0/0/0, directly connected
L   2001:2:3:4::1/128 [0/0]
     via GigabitEthernet0/0/0, receive
S   2001:2:3:4:0:1::/96 [1/0]
     via ::42, NVI0
LC  2001:8:8:8::8/128 [0/0]
     via Loopback0, receive
L   FF00::/8 [0/0]
     via Null0, receive
ASR1000_Test#


6) Here is tracert from PC1 to PC2:

C:\Users\Student1>tracert -d 192.168.10.100

Tracing route to 192.168.10.100 over a maximum of 30 hops

  1     3 ms    10 ms    <1 ms  2.2.2.10
  2    <1 ms    <1 ms    <1 ms  3.3.3.10
  3     *        *        *     Request timed out.
  4  ^C
C:\Users\Student1>

What am I doing wrong? Please help. Thank you.

 

229
Views
0
Helpful
0
Replies
CreatePlease to create content